Tender For Repair/ Maintenance Of Certain Internal Road Of Zone-I & Ii In Aor Of Age B/R-I Under Ge Panagarh
Tender Value
48 Lakhs
Estimated cost
Bid Submission
08 Jul 2026
1 days left
EMD
96000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Panagarh → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/ Maintenance Of Certain Internal Road Of Zone-I & Ii In Aor Of Age B/R-I Under Ge Panagarh
BOQ
| Sl. No. | Item Description |
| 1 | Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exceeding 400 sqm, depth exceeding 50mm and not. exc 100mm deep (Scarifying include racking over and grading the broken up surface to the proper camber etc. as required) , complete all as specified and directed. |
| 2 | M&L total 7.5cm thick (compacted thickness) Water Bound Macadum (WBM), with coarse aggregates of lime stone, Sand stone, Flint or Quartzite grading 2 (63 to 40mm size) or grading 3 (50 to 20mm size) spread, rolled and consolidated to required gradient and camber with 8 to 10 tonne power roller including preparation of unsurfaced WBM surfaces by brushing with wire brushes for removing caked, mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc, complete all as specified and directed.[Note : (i) The finished surface tolerances to be as per Table 900-1 of MoRTH specifications for Road and Bridge Works 2013.(ii) Stack measurement of WBM materials brought at site shall be entered in MB as \\"Not to be abstracted\\" before payment.(iii) Approved certificate of mixing properties & proportion of qty of WBM materials shall be obtained from GE before execution of work. Payment shall be made only after adherence to the same alongwith submission of road roller register/ log book.(iv) Unit rate quoted by bidder shall inclusive testing charges as above & as per MoRTH & no extra claim against testing charges shall be entertained later on.] |
| 3 | M&L & applying evenly a prime coat of Cationic Bitumen emulsion SS-1 conforming to IS : 8887 at a rate of application of 0.7 - 1.0 kg/sqm on surface of WMM/WBM as specified in Table 500-3 of MoRTH specification for Road and Bridge Works 2013, using mechanical sprayer after cleaning of existing surface, complete all as specified and directed. |
| 4 | M&L premixed bituminous macadam over primed surface of road using paving bitumen VG-30 & temperature as per table 500-1 & 500-2 of MoRTH & as per IS : 73, laid/rolled by 8 to 10 tonne capacity roller and compacted to required gradient and camber (consolidated thickness 75 mm or less) including preparation of area before laying of Macadam with mechanical paver, binder contents of premixed macadam shall be 4% by weight of total mix (Design Mix), complete all as specified and directed.[Note : (i) Work shall be executed after approval of design mix of bituminous macadam by GE.(ii) Calibration of Hot Mix Plant shall be submitted to Engr-in-Charge for approval.(iii) Payment shall be made to Contractor after submission of approved design mix, bitumen extraction report, Road Roller register & calibration report.(iv) Exact qty of binder to be used shall be ascertained by Design Mix.(v) Minimum 4% binder shall be used. However, in case more than 4% of binder content is required as per design mix, the same shall be provided by the contractor at no extra cost to dept(vi) Course aggregate's physical property as per MoRTH table 500-6 & mixing of all aggregates as per table 500-7 of MoRTH.(vii) Unit rate quoted by bidder shall inclusive testing charges as above & as per MoRTH & no extra claim against testing charges shall be entertained later on.] |
| 5 | M&L Bituminous semi dense asphaltic concrete, 40mm consolidated thickness with minimum 5.5% binder with paving bitumen (VG-30) [Mix Design criteria as per SSR Part-I Clause 20.B.2.11, or as per MoRTH by Marshal method (Ref table 500-12 to 500-16)] coarse aggregate, fine aggregate, filler cement (OPC - 43 Gde) as per recommendation of design by weight of total mix from hot mix plant, rolled by with 8 to 12 tonne vibrating (tandom) road roller to confirm uniform surface and compacted to required camber and gradient including preparing black top surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. and applying evenly a tack coat of rapid setting cationic bitumen VG-10 conforming to IS : 73 at a rate of application of 0.3-0.4 kg/sqm on bituminous surface as specified in Table 500-5 of MoRTH Specification for Road and Bridge Works 2013, using mechanical sprayer, complete with mechanical paver, complete all as specified and directed.[Note : (i) Work shall be executed after approval of design mix of semi dense asphaltic concrete by GE.(ii) Calibration of Hot Mix Plant shall be submitted to Engr-in-Charge for approval.(iii) Payment shall be made to Contractor after submission of approved design mix, Bitumen Extraction Report, Road Roller Register & Calibration Report.(iv) Exact qty of binder to be used shall be ascertained by Design Mix.(v) Minimum 5.5% binder shall be used. However, in case more than 5.5% of binder content is required as per design mix, the same shall be provided by the contractor at no extra cost to dept.(vi) All testing charges shall include in unit rate quoted by bidder.] |
| 6 | M&L, applying 25mm thick mastic asphalt consisting of an intermate homogeneous mixture of mineral filler, well graded fine and coarse aggregate, industrial grade bitumen meeting the requirement given in table 500-39 of MoRTH, coarse, fine, filler aggregates shall be as per MoRTH table 500-06, 500-40, 500-41 & prepared by using Mastic cooker, as mentioned in SSR Part-I/ MoRTH specification, quantity of bitumen in the range of 14% to 17% of total mix (without coarse aggregate) as indicated in Table : 500-42 of MoRTH cooked at 170 degree to 210 degree centigrade laid hot in temperature 175 degree to 210 degree centigrade trowelled and floated by means of wooden float laid, bitumen mastic after spreading and while still hot in plastic condition shall spread over with bituminous precoated hard fine aggregate of size 9.5mm or 13.5mm @ 0.005 Cum per 10 Sqm and at an approximate spacing of 10cm centre to centre in both direction, poured into surface when the temperature of surface is not less than 100° C, protruding 3mm to 4mm over mastic surfaces as per clause 515 of MoRTH , mixed with 0.17 Kg per 10 Sqm of bitumen of VG-30 meeting the requirement of IS for anti skidding including all material, labour, tools and plants and over & including a tack coat of rapid setting cationic bitumen emulsion RS-1 conforming to IS : 8887 at a rate of application of 0.3-0.4 Kg/Sqm on bituminous surface ensuring the surface is clear & free from loose materials as specified in Table 500-5 of MoRTH specification for road and bridge works 2013, using mechanical sprayer over prepared base as per Design Mix of IRC-107-2013 after cleaning of existing surface complete all as specified and directed. |
| 7 | [Note : (i) Work shall be executed after approval of design mix of mastic asphalt by GE.(ii) Calibration of Mastic Plant shall be submitted to Engr-in-Charge for approval.(iii) Payment shall be made to Contractor after submission of approved design mix, bitumen extraction report & calibration report.(iv) Exact qty of binder to be used shall be ascertained by Design Mix.(v) Unit rate quoted by bidder shall inclusive of testing charges as indicated above & as per MoRTH.] |
| 8 | S&F in repairs Cat Eyes pavement marker compliant to IRC:67 (latest edition) having two way reflective of minimum size (100 to 110)mm x (100 to 130)mm x (24 to 30) mm with aluminium alloy body with micro prismatic lens type technology with reflective lens to be fixed epoxy resin adhesive after cleaning the surface and reflective panels Amber/Red/White the help adhesive and screws, complete all as specified and directed. |
| 9 | S&F in repairs sparkle Solar Road Studs 100% water protection (IP-68), automatic, unbreakable made out of heavy duty weather proof Aluminium Alloy shell di-cast housing with UV-resistant polycarbonate lens mat finished anti twisted ribs on the bottom anchor of size 125mm x 125mm x 25mm (including shank 65mm) both side reflector, rechargeable Ni-MH (Nickel-Metal Hydride)(1600 mA/ 1.2V to 2.4V, view distance upto 10000 to 18000 mcd (milicandela), bearable weight 10 tonne (approx) with bright LEDs as light source complete with integrated battery, sensor optics and stainless solar cell to ensure enerty saving stand along operations including one steel pipe of 20mm dia and 30mm long and 2 component epoxy (hardener & resin), quartz sand for fixing the road stud surface, complete all as specified and directed. |
| 10 | S&F in repairs for Polycarbonate Convex Mirror Outdoor type 800 mm dia made out of fibre along with bracket, Pole mounted and fixed to 80 mm bore Medium Grade MS Pipe of required length, mirror thickness - 3mm, mirror material - polycarbonate, mirror weight - 4 Kg, shape - circular, mirror angle - 130°, fully pipe length - minimum 600mm of black powder coated paint, back holding, plate material - fibre reinforced plastic, body material - ABC plastic complete and embedded in PCC 1:3:6, Type C-1 including necessary earthwork required for post holes, complete all as specified and directed. |
| 11 | S&F in repairs metal retro-reflective Tubular Delineator made out of ABS round body fitted with 2 Nos 100 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe/ post of 1010 mm height duly powder coated (minimum 40 micron) and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including supply and providing of embedding in Plain Cement Concrete 1:2:4 (150 x 150 x 300mm) type B1, complete all as specified and directed.[Note : Delineators shall be made from Class-C full cube corner, micro-prismetic, non metallic, retro-reflective sheets, should meet the reflective value requirement of type XI sheeting specifications as per IRC-67 & meeting the Co-efficient of retro-reflection values as per ASTMD 4956 table specification.] |
| 12 | M&L preparing bituminous surfaces of road by cleaning and preparing the road surface and making good the road marking location and marking / applying 2.5 mm thick white or golden yellow reflective hot thermoplastic road marking paint (Hot application) for centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements confirming to BS 3262-1989 laid down through modern propelled road marking machine with special applicator machine through modern propelled road marking machine in a layer all as per manufacturers instruction and use of all ingredients such as binder, glass beads, titanium dioxide, calcium carbonate, interfiller thermoplastic required for glass beads per sqm by incorporating the white/ yellow beads for reflectivity in 100 mm width, complete all as specified and directed. |
| 13 | M&L Moorum/ red bajri filing in roadside berms laid in layers not exceeding 15cm thickness spread, levelled and rolled including watering using vibratory roller of capacity 8 to 12 tonne static weight and consolidated & compacted to required gradient and camber & compacted 88% to 90% of maximum dry density at optimum moisture content, complete all as specified and directed.[Note : Stack measurement of moorum to be entered in MB as \\"Not to be abstracted\\" for claiming of payment.] Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 15, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayJul 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender