|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. all kind of soil |
| 2 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. Slab |
| 3 | Demolishing R.B. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge. |
| 4 | Boring 300 mm dia piles with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of 300 mm dia diameter and 3 mtr length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) . |
| 5 | Eathwork filling of soil upto 9km. as par direction Enngier |
| 6 | Supply and laying of local sand/stone dust Tank |
| 7 | Rainforced cement concrete 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) work in walls (any thickness) including attached pilasters buttresses, plinth and string courses fillets, columns, pillars, piers, abutments posts nad struts etc. above plinth level up to floor five level excluding cost of centering shuttering finishing and reinforcement. |
| 8 | Centring and shuttring in Plinth beams including strutting, propping etc. and removal of form work. |
| 9 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-lll) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) |
| 10 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) Tank |
| 11 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) |
| 12 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1 :4 (1 cement : 4 coarse sand) |
| 13 | Rainforced cement concrete 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) work in walls (any thickness) including attached pilasters buttresses, plinth and string courses fillets, columns, pillars, piers, abutments posts nad struts etc. above plinth level up to floor five level excluding cost of centering shuttering finishing and reinforcement. |
| 14 | Centring and shuttring in Columns strutting, propping etc. and removal of form work. |
| 15 | Reinforced cement concrete work in beams, suspended floors roofs having slope up to 15 landings, balconies, shelves chajjas, lintels bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level,excluding the cost of centering shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 16 | Centring and shuttring in Lintel including strutting, propping etc. and removal of form work. |
| 17 | Reinforced cement concrete work in beams, suspended floors roofs having slope up to 15 landings, balconies, shelves chajjas, lintels bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level,excluding the cost of centering shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 18 | Centring and shuttring in Lighter Beam propping etc. and removal of form work. |
| 19 | Reinforced cement concrete work in beams, suspended floors roofs having slope up to 15 landings, balconies, shelves chajjas, lintels bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level,excluding the cost of centering shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 20 | Centring and shuttring in slab including strutting, propping etc. and removal of form work. |
| 21 | 12mm cement plaster or mix 1:4(1 cement: 4 coarse sand) |
| 22 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. |
| 23 | Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with machine cut edges of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately). Red sand stone - 30mm thick gang saw cut stone |
| 24 | Providing and laying vitrified tiles in different size of tile 600 x 600 (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S 15622, of approved make in all colours & shade in skirting riser of steps over 12 mm thick bed of cement mortar 1:3 (1 cement: 3coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grounting the joint with white cement & matching pigments etc. complete. W/C |
| 25 | Tile work in skirting, risers of steps and dado up to 2 m hight over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm,including pointing in white cement mixed with pigment of matching shade complete. 8 mm thick |
| 26 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as permanufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture Caretaker Room |
| 27 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Caretaker Room |
| 28 | Steel reinforcement for R.C.C work including starightening, cutting, bending, placing in position and binding all complete upto plinth level Therom-Mechanically Treated bars of grade Fe-500D or more |
| 29 | Providing and fixing with 15 x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) T-iron frames for doors, window and ventilators of mild steel Tee- sections joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, |
| 30 | Providing and fixing M.S. grill of required pattern in frames of steel window windows etc. with M.S flast square or round bras etc. including priming coat with approved steel primer all complete. |
| 31 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Using R4 series with frame (115mm & above) x (45mm & above) & both glazed and fly screen sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. Using R4 series with frame (115mm & above) x (45mm & above) & both glazed and fly screen sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. Using R4 series with frame (115mm & above) x (45mm & above) & both glazed and fly screen sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. Using R4 series with frame (115mm & above) x (45mm & above) & both glazed and fly screen sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. Using R4 series with frame (115mm & above) x (45mm & above) & both glazed and fly screen sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. Using R4 series with frame (115mm & above) x (45mm & above) & both glazed and fly screen sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. |
| 32 | Finshing in steel/Wood work with Deluxe Multi surface paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over and under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture for interious and exteriours using Primer as per manufacturers specifications. |
| 33 | Providing and fixing G.I. pipes 25 mm dia nominal bore complete with G.I. fittings including treching and refilling |
| 34 | Providing and fixing G.I. pipes 15 mm dia nominal bore complete with G.I. fittings including treching and refilling |
| 35 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets. 40 mm flush bend overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid |
| 36 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white Vitreous china Orissa pattern W.C. pan of size 580 x 440 mm with integral type foot rest P.V.C flushing cistem, including flush pipe with manually controlled device (handle lever) conforming to IS 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. |
| 37 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin with 5 litre white P.V.C automatic flushing cistern of 430 x 260 x 350 mm and 340 x 410 x 265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete including painting of fittings and brackets cutting and making good the walls and floors wherever required. |
| 38 | Providing and fixing wash basin with C.I. brackets 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 39 | P/F of of Nahani trap i/c all complete |
| 40 | Providing and fixing soil Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS :3989 West and vent pipe . |
| 41 | Providing and fixing soil Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS :3989 West and vent pipe . |
| 42 | Providing and laying cement concrete 1:5:10(1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) all round 150 mm diameter S.W. pipe including bed concrete as per standard design. |
| 43 | Providing and laying cement concrete 1:5:10(1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) all round 100 mm diameter S.W. pipe including bed concrete as per standard design. |
| 44 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) 25 mm nominal dia pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1:00 m spacing This includes jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work including cutting chases and making good the walls etc. |
| 45 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) 20 mm nominal dia pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1:00 m spacing This includes jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work including cutting chases and making good the walls etc. |
| 46 | Providing and fixing PTMT bib cock 15mm nominal bore, 86 mm long, weighing not less then 88 gms of approved quality and colour. |
| 47 | Providing and fixing PTMT stop cock 15 mm nominal bore 86 mm long, weighing not less then 88 gms of approved quality and couler. |
| 48 | Providing and fixing PTMT angle stop cock 15 mm nominal bore weighing not less then 85 gms . |
| 49 | Providing and fixing mirror of superior glass (of approved quality) and of required Rectangular shape and size 1500 x 450 mm with plastic moulded frame of approved make and shade with 6 mm thick hard board backing. |
| 50 | S/F Granite Stone all complete work as per Directed by E/I |
| 51 | Providing and placing on terrace(at all floor levels) polyethylene water stroge tank IS : 12701 maked, with cover and suitable locking arrangment and making necessary holes for inlet outlet and overflow pipes but without fittings and the base support for tank. |
| 52 | Providing and fixing fo C.P. brass toilet peper holder. |
| 53 | Providing and fixing PTMT liquid soap container 109 mm wide 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and coulur weighing not less then 105 gms. |
| 54 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fitting arrangement of approved quality and colour weighing not less than 88 gms. |
| 55 | 18mm thkHDMR board with laminate sheet on both sides (as/approval) and approved hardware including legs, hinges, handles, channels and latches |
| 56 | Fixing and cartage of Item no |
| 57 | With ss hardware, 12mm toughened glass 4'x2' size. |
| 58 | Witing for twin control light point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm PRLS PVC insulated copper counductor single core cable etc. as required. |
| 59 | Wiring for light point fan point/call bell point with 1.5 sq.mm FRLS PVC insuilated copper conductor single core cablein surface/recessed medium class PVC conduit with plano type switch phenolic laminled sheet suitable size M.S. box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc as required. |
| 60 | Supply and writing of 4 number 10 sq.mm FRLSH PVC insulated 1100 V grade sngle core copper 32 mm dia heavy gauge rigid PVC conduit on surface with 2 number 6 sq.mm single copper conductor cable as earth continully wire drawn in condiit complete in all respect. |
| 61 | Installation, testing and commissioning of celling fan including wiring the down road of standard length (upto 30cm) with 1.5 sq.mm FRLS PVC insylated, copper conductor, single core cable etc, as required. |
| 62 | Instalation of exhaust fan in the existing opening including making good the damage connection lesting commissioning etc. DSR No. 1.50 |
| 63 | S/F of single light wall bracket on matching M.D.F.E.G board baseetc complete in all respects. category AAA |
| 64 | Earthing with G.I earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with cover plate having locking arrangment and watering pipe of 2.7 meter long etc.with charcoal/coke and salt as required. |
| 65 | Supply & Laying of 25 mm x 3mm G.I. strip from earth lectrode directly in the ground as required complete in all respects. |
| 66 | Supply and fixing of with two number 8 SWG G.I. wire in 15mm dia G.I. pipe for earthing, laid in ground or in wall duly concealed including the cost of cement, sand, labour, T&P other material required for proper completion of the work as directed at site. |
| 67 | Supply, Installation, Testing and Commissioning of 1200 mm sweep. BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos, canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS: 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 egree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 68 | Supply and erection of A.C. 230 /250 volts 50 Hz exhast fan including providing nuts bolts, mounting frame and other accessaries including connection etc. complete as required 450 mm sweep |
| 69 | Supply and fixinf of IP 20 Front lite Mid power SMD type LED light recess/Surface mounting round 6 watt to 9 watt, cut out min 125 mm Height min 40 mm LED Down Lighter having Powder coated dia cast aluminium housing with heat sink, High purity/ transmisivity UV Stabilized non yellowish diffuser/Reflector for uniform light distribution detachable driver set suitable for 24 Hr Continuous Operation Complete in All respect 660-990 system lumens>110Lm/W, PF>0.95, THE<10%at full load CRI> 80 with 3 years warrantee. SI No. 23.01 CAT-AA |
| 70 | Supply and fixinfg of IP 20 Front Lit Mid power SMD type LED Light recess/Surface mounting round 18 watt to 20 watt cut out min 150mm Hight min 40 mm LED Down Lighter having Powder coated die cast aluminium housing with heat sink, High purity/transmisivity UV stabilized Non yellowish diffuser/Reflector for uniform light distribution detachable driver set suitable for 24 Hr Conlinuous Operation Complete in All Respect. 1980-2200 System lumens, > 110 Lm/W PF>0.95 THE<10% at full load CRI>80, with 3 years warrantee. SI No. 23.03 CAT-AA |
| 71 | Providing and fixing following capacity 32 A TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections. Etc as required. |
| 72 | Supplying and fixing Single pole and neutral 5A to 32 A rating, 240/415 V, 10 ka, \\"C\\" curve miniature circuit breaker suitable for load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. |
| 73 | Add 18% GST Please Enable Macros to View BoQ information |
