|
| 1 | 2.2 Clearing and Grubbing Road LandClearing and grubbing road land including uprooting rankvegetation, grass, bushes, shrubs, saplings and trees having girth up to 300 mm, removal of stumps of trees cut earlier and disposal ofunserviceable materials and stacking of serviceable material up to a lead of 1000 metres including removal and disposal of top organicsoil not exceeding 150 mm in thickness. |
| 2 | 10.1 Repair to pot holes and removal of loose material, trimming of sides, cleaning of surface by providing tack coat with bitumen emulsion, 20mm thick pre-mix carpet using catonic bitumen emulsion @ 21.5 kg per 10 sqm and seal coat type B with bitumen emulsion @ 10kg per 10 sqm as per technical specification and compacting with three wheeled 80-100 kN Static Roller |
| 3 | 10.19 Crack stitching with inclined tie bar (cross Stitching) used for cracks in reasonably good condition in order to arrest movement of slab and slabs pieces by making primer verticals holes,, alternative inclined hole, cleaning the hole through oil free compressor and filled with epoxy resin in enough quality that will coat HYSD bar confirming IS 1786 of 12 mm dia in every hole also groone shall be made along with line cracks display spalling and filled with a low viscocity resin or fire epoxy mortar following the method specified IRC SP 83:2008. |
| 4 | 10.13 Repair of joint Grooves with Epoxy MortarRepair of spalled joint grooves of contraction joints, construction joint, longitudinal joints and expansion joints in concrete pavements using epoxy mortar or epoxy concrete. |
| 5 | 10.14 Repair of old Joints SealantRemoval of existing sealant and re-sealing of contraction, construction longitudinal or expansion joints in concrete pavement with fresh sealant material |
| 6 | 10.12 Repair to cement concrete road by providing laying & Fixing mortar-based patch master & Liquid rapid harding chemical including cleaning of concrete surface and applying of special bounding liquid |
| 7 | 4.2 Crusher Run Macadam Sub Base/Base CourseProviding crushed stone aggregate, depositing on a prepared surface by hauling vehicles, spreading and mixing with a motor grader, watering and compacting with a vibratory roller as per clause 410 to form a layer of sub-base/Base in accordance to Table No. 400-14, 400-15 and as per clause of section 407 of specifications. |
| 8 | 4.3 Wet Mix MacadamProviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density in accordance to Table No. 400-12, 400-13 and as per clause of section 406 of specifications. |
| 9 | 5.1 Prime coatProviding and applying primer coat with bitumen emulsion on prepared surface of granular Base including cleaning of road surface and spraying primer at the rate of 0.75 kg/sqm using mechanical means as per clause 502 of specifications. |
| 10 | 5.3 Providing and applying tack coat with catonic bitumen emulsion (RS-1) using emulsion pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom and as per relevant clauses of section-503 of specifications.(i) @ 0.25 kg per sqm (normal bituminous surfaces) |
| 11 | 5.3 Providing and applying tack coat with catonic bitumen emulsion (RS-1) using emulsion pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom and as per relevant clauses of section-503 of specifications.(ii) @0.30 kg per sqm (dry & hungry bituminous surfaces /Granular surfaces treated with primer) |
| 12 | 5.9 Open - Graded Premix SurfacingProviding, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or cut-back or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a smooth wheeled roller 8-10 tone capacity, finished to required level and grades all complete as per clause 510 of specification.(i) Case - I: Mechanical method using Penetration grade Bitumen VG 30 and HMP of appropriate capacity not less than 75 tones/hour. |
| 13 | 5.11 Seal CoatProviding and laying seal coat, sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A and B seal coats, all complete as per clause 511 of Specification.(ii) Case - II: Type B (Providing and laying of premix sand seal coat using HMP of appropriate capacity not less than 75 tonnes/ hours using crushed stone chipping (aggregate shall pass 2.36mm sieve and retained to 180-micron sieve) and penetration bitumen VG 30 of suitable grade all complete as per clause 511 of specification. |
| 14 | 8.3 Retro- reflectorised Traffic signsProviding and fixing of retro-reflectorised cautionary, mandatory and informatory sign board as per IRC 67-2012 made of high intensity Micro-Prismatic Grade Sheeting (Type XI) vide IRC: 67:2012 clause 6.7.3.2 and clause 801.3.3 of MoRT&H fixed over Aluminum composite material sheet with thermoplastic core of Low density polyethylene (LDPE) between two thick skins/sheets of aluminum with overall thickness of 4mm and aluminum skin of thickness 0.3 on both side, the ACM shall conform to Table 6.1 of IRC:67:2012 and Table 800-1 of MoRT&H specification and High Intensity Micro Prismatic Grade Sheeting shall conform to Table 6.6 of IRC:67:2012 and Table 800-3 of MoRT&H specification of in the clause IRC 6.8 of the IRC 67-2012 and clause 801.3.7 of MORTH message legend numerical letter etc. and borders shall be screen printed on high intensity micro prismatic sheeting shall conform to clause 801.3.7 with digital printing ink or of cutout from transparent durable overlay or cutout from the same type of reflecting sheeting for cautionary/ mandatory/ signs, supported on MS sign post of size 75mm x75mm x 6mm of 3.60 meter over all length and fix to ground by means of properly designed foundation of dimension 450x450x600mm with M20 grade concrete. The ACM sheet shall be fixed to the post with four minimum four number breakaway bolts. & supported with a back support frame of 25mmx25mmx3mm angle. 10 years warranty for Retro Reflection Sheeting to be provided from the original sheeting manufacture as per clause 6.9 of IRC: 67:2012 & a certified copy for three years for outdoor exposure report from an independent test lab as per clause 6.7 of IRC: 67:2012 for the product offered shall be submitted by the contractor.i) 90 cm equilateral triangle |
| 15 | ii) 60 cm equilateral triangle |
| 16 | iii) 60 cm circular |
| 17 | iv) 80 mm x 60 mm rectangular |
| 18 | v) 60 cm x 45 cm rectangular |
| 19 | 8.5 Direction and Place Identification signs more than 0.9 sqmsize board.Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign board as per IRC 67-2012 made of high intensity Micro-Prismatic Grade Sheeting (Type IV) vide IRC: 67:2012 clause 6.7.3.2 and clause 801.3.3 of MoRT&H fixed over Aluminum composite material sheet with thermoplastic core of Low density polyethylene (LDPE) between two thick skins/sheets of aluminum with overall thickness of 4mm and aluminum skin of thickness 0.3 on both side, the ACM shall conform to Table 6.1 of IRC:67:2012 and Table 800-1 of MoRT&H specification and High Intensity Micro Prismatic Grade Sheeting shall conform to Table 6.6 of IRC:67:2012 and Table 800-3 of MoRT&H specification of in the clause IRC 6.8 of the IRC 67-2012 and clause 801.3.7 of MORTH message legend numerical letter etc. and borders shall be screen printed on high intensity micro prismatic sheeting shall conform to clause 801.3.7 with digital printing ink or of cutout from transparent durable overlay or cutout from the same type of reflecting sheeting for cautionary/ mandatory/ signs, supported on MS sign post of size 75mm x75mm x 6mm of 3.60 meter over all length and fix to ground by means of properly designed foundation of dimension 450x450x600mm with M20 grade concrete. The ACM sheet shall be fixed to the post with four minimum four number breakaway bolts. & supported with a back support frame of 25mmx25mmx3mm angle. 7 years warranty for Retro Reflection Sheeting to be provided from the original sheeting manufacture as per clause 6.9 of IRC: 67:2012 & a certified copy for three years for outdoor exposure report from an independent test lab as per clause 6.7 of IRC: 67:2012 for the product offered shall be submitted by the contractor. |
| 20 | 8.22 Supplying and installation of delineators (road way indicators,hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide stripes, fitted with 80 x100 mm rectangular or 75 mm dia circular reflectorised panels at thetop, buried or pressed into the ground and confirming toIRC-79 and the drawings. |
| 21 | 8.36 Kilo Metre StoneReinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting andprinting etc(i) 5th kilometre stone (precast) |
| 22 | (ii) Ordinary Kilometer stone (Precast) |
| 23 | (iii) Hectometer stone (Precast) |
| 24 | 10.32 Providing painting, figuring and numbering as per IRC specifications complete with Synthetic Enamal Paint for 5th Km. Stone. (i) Two coats on new work. |
| 25 | 10.32 Providing painting, figuring and numbering as per IRC specifications complete with Synthetic Enamal Paint for 5th Km. Stone. (ii) One coat on old work. |
| 26 | 10.33 Providing painting, figuring and numbering as per IRC specifications complete with Synthetic Enamal Paint for ordinary Km. Stone. (i) Two coats on new work. |
| 27 | 10.33 Providing painting, figuring and numbering as per IRC specifications complete with Synthetic Enamal Paint for ordinary Km. Stone. (ii) One coat on old work. |
| 28 | 10.34 Providing painting, figuring and numbering as per IRC specifications complete with Synthetic Enamal Paint for 0.2 Km. Stones or Boundary Stones..(i) Two coats on new work. |
| 29 | 10.34 Providing painting, figuring and numbering as per IRC specifications complete with Synthetic Enamal Paint for 0.2 Km. Stones or Boundary Stones..(ii) One coat on old work. |
| 30 | 10.26 Providing painting to angle Iron posts of road sign boards complete with Synthetic Enamel Paint |
| 31 | 4.13 Construction of Shoulders with approved material/selected soili/c excavation all lifts & leads i/c grading to required slope &camber of 4% and compacting using vibratory roller of 80 to 100kN static weight to meet requirement as per relevant clause of400(B) Hard Shoulders (CBR value >12) |
| 32 | 8.17 Type - A, \\"W\\" : Metal Beam Crash Barrier (Providing and erecting a \\"W\\" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, however 5 spaces of 600mm each between vertical post and 5 spaces of 900mm each between vertical post will be kept adjacent to RCC parapet/ concrete crash barrier in accordance to figure 9.14 of the IRC-SP: 73-2018, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811) and treatment for metal beam cresh barrier on approach shall be modified eccentric loader terminal arrangement as shown in figure 9.12 of IRC- SP : 73-2018 End portion of metal beam crash barrier shall be flared outside by1.25 mtr. Distance in last section of 8 mtr. Length. Departure side it shall be trailing terminal (TT) arrangement as shown in figure 9.13 of the IRC SP-73- 2018. End portion of metal beam crash barrier shall be flared outside by 0.35 mtr. Distance in last section of 8 mtr. length |
| 33 | 10.61 The maintenance of all type of drains including erosion, repair,clearing, cleaning, reshaping, regrading, deepening of side drainsas well as catch water drains as per technical specification including all material, labour, etc. complete. |
| 34 | 16.5 Providing and laying suitable designed Filter material underneath pitching in slopescomplete as per drawing and Technical specification |
| 35 | 14.4 Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specificationsA. Stone/Boulder |
| 36 | 17.6 Patching of damaged concrete surface with polymer concrete and curing compounds, initiator and promoter, available in present formulations, to be applied as per instructions of manufacturer and as approved by the Engineer. |
| 37 | 17.7 Sealing of crack/porous concrete with Epoxy Grout by injection through nipples complete as per clause 2803.1. |
| 38 | 17.8 Applying epoxy mortar over leached, honey combed and spalled concrete surface and exposed steel reinforcement complete as per Technical specification |
| 39 | 17.9 Removal of defective concrete, cleaning the surface thoroughly, applying the shotcrete mixture mechanically with compressed air under pressure, comprising of cement, sand, coarse aggregates,water and quick setting compound in the proportion as per clause 2807.1., sand and coarse aggregates conforming to IS: 383 and table 1of IS: 9012 respectively, water cement ratio ranging from 0.35 to 0.50, density of gunite not less than 2000 kg/cum, strength not less than 25 Mpa and workmanship conforming to clause 2807.6. |
| 40 | 10.1 Repair to pot holes and removal of loose material, trimming of sides, cleaning of surface by providing tack coat with bitumen emulsion, 20 mm thick pre-mix carpet using catonic bitumen emulsion @ 21.5 kg per 10 sqm and seal coat type B with bitumen emulsion @ 10kg per 10 sqm as per technical specification and compacting with three wheeled 80-100 kN Static Roller |
| 41 | 5.9 Open - Graded Premix SurfacingProviding, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or cut-back or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant,laying and rolling with a smooth wheeled roller 8-10 tone capacity, finished to required level and grades all complete as per clause 510 of specification.(i) Case - I: Mechanical method using Penetration grade Bitumen VG 30 and HMP of appropriate capacity not less than75 tones/hour. |
| 42 | 5.11 Seal Coat Providing and laying seal coat, sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A and B seal coats, all complete as per clause 511 of Specification(ii) Case - II: Type B (Providing and laying of premix sand seal coat using HMP of appropriate capacity not less than 75 tonnes/ hours using crushed stone chipping (aggregate shall pass 2.36mm sieve and retained to 180- micron sieve) and penetration bitumen VG 30 of suitable grade all complete as per clause 511 of specification. |
| 43 | 8.38 Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beeds on Bituminous surface. Providing and applying (Cleaning of Bituminous surface) thermoplastic compound having composition of binder (Resin)minimum 18 %, titanium dioxide minimum 10 % and intermixed glass beed, minimum 30% of brand like Asian, Burger or equivalent make of 2.5 mm thick including drop down reflectorizing, glass beeds @ 250 gms per sqm area thickness of2.5 mm is exclusive of surface applied glass beeds as per IRC:35.The finished surface to be level, uniform and free from streaks and holes, all complete as per clause 803 of specifications |
| 44 | 8.39 Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beeds on Concrete surface. Providing and applying (Cleaning of concrete surface and afterapplying Concrete primer) thermoplastic compound having composition of binder (Regin) minimum 18 %, titanium dioxide minimum 10 % and intermixed glass beed, minimum 30% of brand like Asian, Burger or equivalent make of 2.5 mm thickincluding drop down reflectorizing, glass beeds @ 250 gms per sqm area thickness of 2.5 mm is exclusive of surface applied glassbeeds as per IRC:35 along with concrete primer. The finishedsurface to be level, uniform and free from streaks and holes, all complete as per clause 803 of specifications. |
| 45 | 4.16 Construction of Shoulders with approved material/selected soili/c excavation all lifts & leads i/c grading to required slope &camber of 4% and compacting using vibratory roller of 80 to 100kN static weight to meet requirement as per relevant clause of400(A) Hard Shoulders (CBR value >12) |
| 46 | Emergency Provision for works during flood/earthquake etc. to be utilised during 5years if required Please Enable Macros to View BoQ information |
