|
| 1 | Excavating in trenches n exc 1.50m in width and n exc 1.50m in depth for foundation, manholes etc as well as n exc 10 sqm on plan area and getting out in soft/loose soil all as specified and directed. |
| 2 | M&L for PCC 1:5:10 type E-2, using 40mm graded crushed stone aggregate in foundation, filling and mass concrete complete all as specified and directed. |
| 3 | M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6m radius, built in CM in 1:6 all as specified and directed. |
| 4 | Returning, filling in including spreading, watering & well ramming in layers n exc 25 cm thick complete all as specified and directed. |
| 5 | Removal of surplus soil to a distance n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as speficied and directed by Engr-in-Charge. |
| 6 | M&L for broken stone hard core of gauge n. exc 63mm, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface all as specified and directed. |
| 7 | M&L for RCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate in lintel upto 1.5m clear span, cills, steps, coping and similar work all as specified and directed. |
| 8 | M&L for RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in foundation including rafts, footing, foundation beams, bases for columns, etc and mass concrete all as specified. |
| 9 | M&L for RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in columns, pillars, piers, posts and struts all as specified. |
| 10 | M&L for RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in beams, cantilevers, bressumers, lintels,plinth beam etc complete all as specified and directed. |
| 11 | S&F 10mm dia and above TMT bars cut to length, bend to shape as required including cranking, hooking ends & binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 12 | S&F mild steel deformed bars, 6mm to 8mm dia cut to length, bent to shape required including cranking and binding with & including mild steel wire (annealed) not less than 0-.90mm dia complete all as specified and directed. |
| 13 | All as item No 12 here in before but 5mm dia and over upto & including 10mm dia in stirrups, spaces & binder complete all as specified and directed. |
| 14 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed. |
| 15 | Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete complete all as specified and directed. |
| 16 | M&L for rendering 10 MM thick in cement mortar (1:6) finished even smooth complete all as specified on brick or concrete surface of fair faces complete all as specified and directed. |
| 17 | M&L 15mm thick cement plaster in CM 1:4, finishing fair & even on brick or concrete surfaces of other than fair faces complete all as specified and directed. |
| 18 | M&L for preparation of newly plastered surfaces and applying two coats of cement base paint over a coat of chalk whiting complete all as specified and directed. |
| 19 | M&L for preparation of new plastered surfaces of walls /RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc and applying 02 coats of interior emulsion paint (light shade) by using roller over & including a coat of wall primer and over a coat of acrylic wall care putty to make the surfaes smooth complete all as specified and directed. |
| 20 | M & L 75mm thick PCC 1: 4: 8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed. |
| 21 | S&F MS work in tubular/pipe/angle sections for frame work for roof, vertical poles, s rafters and purlins including washer etc complete all as specified and directed. |
| 22 | S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed. ( Design of sheet as mangalore tiles pattern in Red colour ). |
| 23 | M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enameled paint over a coat of red oxide primer all as specified and directed. |
| 24 | M&L for 75 mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection/floors complete all as specified and directed. |
| 25 | M&L for single charge, vitrified, stain & scratch resistant, premium quality coloured tiles area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc and 8-10 mm thick, in any pattern of light & dark tiles as approved, laid over 15 mm thick screed in CM (1:6) Epoxy Cartridge tile Grout using fill the joint of tiles complete all as specified.Note- Epoxy Black,Golden Colour,complete all as specified and directed. |
| 26 | All as per item no 25 above but as in skirting over 10 mm thk rendering in CM 1:4 complete all as specified and directed. |
| 27 | M&L for ceramic glossy finish, joint free premium quality coloured tiles 600 X 1200 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. |
| 28 | M & L for 15 mm thick Artificial Granite (of any type) work steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. including Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes complete all as specified. |
| 29 | S&F for UPVC pipe fixed on wall/ceiling or laying in floor of 15mm bore fittings complete all as specified and directed. |
| 30 | S&F for UPVC pipe fixed on wall/ceiling or laying in floor of 20mm bore fittings complete all as specified and directed. |
| 31 | S&F for Angle stop cock with wall flange 15mm cast copper alloy, screwed for iron pipe or for brass ferrule long body.Make: Jaquar Cat Part No-FON-40053PM or equivalent /Hindware/Kohlar. |
| 32 | S&F 15 mm bore bib cock with wall flange, cast copper alloy, chromium plated, fancy type with screwed down, screwed for iron pipe or for brass ferrule long body.Make: Jaquar Cat part No OPP-15037PM or per equivalent /Hindware/Kohlar. |
| 33 | S&F brass chromium plated Basin mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore all as specified and as directed. Make: Jaquar Cat Part No ORP-10011BPM or per equivalent /Hindware/Kohlar |
| 34 | S&F 15mm CP connection 600mm long including washer and brass nuts all as specified. |
| 35 | S&F vitreous china rimless single piece WC of Size: 385x720x710 mm, Single Piece WC with PP Soft close Seat cover, Hinges, Fixing Accessories, Accessories Set, and Cistern fittings, S trap-300mm complete all as specified and directed Make Jaquar cat part No ONS-WHT-10853P300UFSM or equivalent in kohlar, grohe and Roca |
| 36 | S&F toilet Roll holder stainless steel flap all as specified. Make- Jaquar Cat Part No CAN-1153S or per equivalent /Hindware/Kohlar |
| 37 | S&F towelRack 600mm long with lower hanger (stainless steel) all as specified.(Make: Jaquar Cat Part No ACN -1181S or equivalent /Hindware/Kohlar |
| 38 | S&F Soap Dispenser with glass bottle (stainless steel) all as specified. Make- Jaquar Cat Part No ACN -1135N or equivalent /Hindware/kohlar |
| 39 | S&F Soap Dish holder with glass (stainless steel) all as specified. Make- Jaquar Cat Part No AKP -35731P or equivalent /Hindware/kohlar |
| 40 | S&F towel ring Square with round flange (stainless steel) all as specified. Make- Jaquar Cat Part No ACN -1121N or per equivalent /Hindware/Kohlar |
| 41 | S&F healthfaucet with 1mtr long easy flex tube in chrome Finish and wall hook of 15 mm bore with CP pipe complete set of make -Jaquar cat part No ALD - 565 or equivalent, parryware/Prayag |
| 42 | S&F in repair looking mirror 5mm thick size 3.5x3.5 feet incl stud and finishing all as specified. |
| 43 | S&F in Double Arm wall mounted reversible plain/Magnifying (X3) pivotal Mirror all as specified. Jaquar Cat Part No ACN -1193N or per equivalent /Hindware/Kohlar |
| 44 | S&F glass shelf corner with bracket of size 225mm x 225mm thickness of glass 6mm) with CP brass railing and brass screws.Make- Jaquar Cat Part No ACN -1173 or equivalent /Hindware/kohlar |
| 45 | S&F grating doom 125mm of PTMT. |
| 46 | S & F Vitreous China urinal half stall type white (excluding flushing cistern ) including waste fitting, waste pipe Complete all as specified.Make-Jaquar/Hindware/kohlar |
| 47 | M& L for 25mm thick PCC 1:2:4 type BO using 12.5 mm graded stone aggregate as in floor complete as specified and directed. |
| 48 | S&F factory made UPVC black colour(Matt Finish) door shutter made of extruded profile with wall thickness of 2.3mm(+-0.2mm) door profile with hollow section with multy chamber. Frame (60x62mm),sash(42mmx67mm).sliding interlock(one verticle length in each shutter)(45.5mmx28mm).Glazing bead(24.5mmx16mm)will be mittred cut and fusion welded at all corner.including drilling holes for fixing hardware and drainge of water etc am,.making arrangement for fixing of hardware.EPDM gasket,1.2+0.2 mm thick galvanised steel frame(30mmx21.5mm).sash (30mmx18mm)profile to be inserted in required profile.frame will be finshed to the wall with 8mmx100mm long fasteners.hardware touch lockof zinc alloyed(brown powder coated)steel roller system including 5mm thick glazing with selected quality glass ,aluminium track and bottom rail for two track sliding fram,wool pine for sliding sash and interlock. Note.The unit rate coated by contractor includes cost of glass and all other conncted accessories,net opening will be measured for purpose. |
| 49 | S&F 10- 12mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required including all necessary fittings (patches, connectors, brackets etc) complete all as specified and directed. |
| 50 | M&L of false ceiling in step(s) comprising of 12mm thick Gyp board including GI frame work for seamless ceiling made of GI perimeter channel 0.55mm thick with two unequal flange of 20 to 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screw at 450 mm centre to centre intermediate channel 0.9mm thick having two equal flange of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleats and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thicknesshaving kurledweb of 50mm and flangeof 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre with and including two coats of plastic emulsion paint complete all as specified and directed. (Note:- The measurement shall be made from wall to wall without considering step(s). |
| 51 | S&F for powder coated aluminium ventilator shutters with frame not less than 0.55 Kg/Rm, half bottom portion fixed with 4mm thick glass with fixed type shutter and top half portion lower type with 4mm thick glass and outer side fixed with stainless steel wire mesh, shutters aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, necessary aluminium fittings etc complete all as specified and directed. Note: Minimum thickness of powder coating shall be 55 microns. Please Enable Macros to View BoQ information |
| 52 | S&F for powder coated aluminium ventilator shutters with frame not less than 0.55 Kg/Rm, half bottom portion fixed with 4mm thick glass with fixed type shutter and top half portion lower type with 4mm thick glass and outer side fixed with stainless steel wire mesh, shutters aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, necessary aluminium fittings etc complete all as specified and directed. Note: Minimum thickness of powder coating shall be 55 microns. Please Enable Macros to View BoQ information |
