|
| 1 | Labour |
| 2 | Constructing Transformer plinth of size 1.5x1.5x1.5mon 1.8x1.8x0.75 m basement inclusive of cost of all materials. [Excavation 1.8x1.8x0.75m, Random Rubble in CM(1:6) 1.8x1.8x0.75m + 1.5x1.5x1.5m, concrete (1:2:4, 20mm) 1.5x1.5x0.10 m, plaster CM (1:3) 12mm, 1.5x1.5m, Pointing CM (1:3) 1.5x1.5mx 4 sides] |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan ), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 4 | Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. - Ordinary rock |
| 5 | Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. Hard rock (blasting prohibited) |
| 6 | Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials-All kinds of soil |
| 7 | Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.-Ordinary or hard rock |
| 8 | Close timbering over areas including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered): Depth not exceeding 1.5 m |
| 9 | Close timbering over areas including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered): Depth exceeding 1.5m but not exceeding 3m |
| 10 | Bailing out water Using 5HP Pump- Bailing out water with 5HP engine and pump set including conveyance to site anderection,cost of fuel, lubrication oil and other stores, pay of staff etccomplete |
| 11 | De watering manually. |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns |
| 13 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up toplinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 14 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete and Medium Tensile steel bars |
| 15 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size |
| 16 | Additional rate for excavation of one Earth Pit (2.5m depth) in Laterite. |
| 17 | Additional rate for excavation of one Earth Pit (2.5m depth) in HardLaterite. |
| 18 | Additional rate for excavation of one Earth Pit (2.5m depth) in Soft Rock. |
| 19 | Additional rate for excavation of cable trench of appropriate size (normally 1.2m deep and 0.35m /0.5m wide for single/double run) in exceptionally hard conditions (like in ordinary rock). * (As per the PWD Standard Data book ,ordinary rock is defined as any material which can be quarried or split withcrowbars or wedges). |
| 20 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cmin depth, consolidating each deposited layer by rammingand watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 21 | Additional rate for excavation of Pit for A type pole in Laterite. |
| 22 | Additional rate for excavation of Pit for A type pole in Hard Laterite |
| 23 | Additional rate for excavation of Pit for A type pole in Soft Rock |
| 24 | Filling with Quarry Muck Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, levelingthe top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade |
| 25 | Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as perdirection of Engineer - in Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 26 | Excavation of cable trench of appropriate size ( normally 1.2m deep and 0.35m /0.5m wide for single/double run) in all classes of soil including breaking clods, watering, ramming and sectioning of soil bank etc. and back filling the soil after cable laying and layers of 75cm (excluding laying of cable). |
| 27 | Supplying and laying RCC (Pre-cast) slab of size 0.5mx0.3m with height sloping from 0.08m to 0.05m using cement concrete 1:2:4,20mm metal (Nominal size) and reinforced as per accompanying sketch, engraving KSEB 33 kV CABLE, suitably and adequately cured etc complete as per the standard specifications and direction of Board staff at site |
| 28 | Surveying one km 11kV line using Theodolite. |
| 29 | Dismantling (without damage) one V cross arm/Channel cross arm from existing Pole and bringing back to section store. |
| 30 | Fitting and providing one HT Fly stay for 11kV pole usingHT PSC pole including digging and back filling pits in ordinary soil, drawing sufficient length of GI earth leads to the ground for earthing (excluding provision of earthing). |
| 31 | Fitting Knee bracing or suitable support on existing HT or LT post |
| 32 | Fitting one LT 2 line cross arm on HT or LT existing poles including fitting insulators and binding the same with LT Line |
| 33 | Fitting one LT 4 line cross arm on HT or LT existing poles including fitting insulators and binding the same with LT Line |
| 34 | Dismantling one section fuse from structure and bringing back to section store. |
| 35 | Fitting one No. Section fuse on LT line with dropping cables, crimping sockets, connecting with bolt & nut etc |
| 36 | Drilling oval shaped hole of various sizes on existing hannel/Cross Arm/GI/MS cleat etc |
| 37 | Providing/Inserting 2 line spacer on the existing LT OH line. |
| 38 | Providing/Inserting 3 line spacer on the existing LT OH line |
| 39 | Dismantling one damaged HT TW/RSJ/Rail Strut pole including removal of clamps and stacking |
| 40 | Dismantling (without damage) one HT TW/RSJ/Rail Strut poleincluding removal of clamps and stacking. |
| 41 | Dismantling one LT 2 line cross arm with clamp from existing pole and stacking. |
| 42 | Dismantling one LT 4 line cross arm with clamp from existing pole and stacking. |
| 43 | Numbering of Tree (marking for cutting the tree) using yellow enamel paint as specified including cost of paint. |
| 44 | Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. (cost index(e) : 1.3132 included in Rate) |
| 45 | Dismantling (without damage) one km LT three phase 4 wire OH line conductor by dismantling cross arms, insulators andstacking the conductors in rolls properly. |
| 46 | Dismantling (without damage) one km LT additional conductor line by dismantling cross arms, insulators and stacking the conductors in rolls properly. |
| 47 | Stringing, shackling, fitting cross arms, insulators and binding, giving jumper connection etc. using ACSR Rabbit for Phase and Neutral, for one km LT single phase 2 wire line including cuttingand removing tree branches wherever necessary andconveyance of all materials (except poles) from stackingplace. |
| 48 | Stringing, shackling, fitting cross arms, insulators and binding, giving jumper connection etc. using ACSR Rabbit for Phase & Neutral and ACSR Weasel for street main, for one km LT singlephase 3 wire line including cutting and removing tree branches wherever necessary and conveyance of all materials (except poles) from stacking place |
| 49 | Stringing, shackling, fitting cross arms, insulators and binding, giving jumper connection etc. using ACSR Rabbit for Phase and ACSR Weasel for Neutral, for one km LT three phase 4 wire line including cutting and removing tree branches wherever necessary and conveyance of all materials (except poles) from stacking place. |
| 50 | Stringing, shackling, fitting cross arms, insulators and binding, giving jumper connection etc. using ACSR Rabbit for Phase and ACSR Weasel for Neutral & Street Main, for one km LT 3ph 5 wire line including cutting and removing tree branches wherever necessary and conveyance of all materials (except poles) from stacking place. |
| 51 | Reshackling one span LT single phase 2 wire OH line including pin binding, jumpering, replacing insulators/cross arms/shackle,tightening stay, cutting tree branches etc. wherever necessary including conveyance of all materials. |
| 52 | Fitting and providing one Strut using A type pole, including digging and back filling pit in ordinary soil. |
| 53 | Erection of one set 33KV Bus Isolator on the already erected structure including opening crates and conveyance of all accessories from the place of storage to the place of erection to lines and levels including erection of mechanism box checking operation and aligning properly as per the direction of departmental officers. |
| 54 | Fitting one Additional V cross arm in existing single pole including conveyance of materials |
| 55 | Drilling hole of various sizes on existing Channel/Cross Arm. |
| 56 | Filing of holes |
| 57 | Cutting Channel/Cross Arm/Angle Iron into two pieces. |
| 58 | Welding charge for welding on iron parts using arc welding as per standards |
| 59 | Providing Bucket type cradling for one span 11kV line using 8 SWG GI wire including provision of two stays and drawing sufficient length of GI earthing leads to the ground for earthing,excluding provision of earthing. |
| 60 | Additional rate for providing one HT Pin with insulator, complete on any type of HT pole. |
| 61 | Fitting one Additional 2.4m Channel cross arm in existing single pole including conveyance of materials. |
| 62 | Fitting one Additional 75x40mm, 1.8m Channel cross arm in existing single pole including conveyance of materials. |
| 63 | Fitting one Additional 2.4m/3m Channel cross arm 100x50x6mm), in existing 11kV DP including conveyance of materials. |
| 64 | Re-Tensioning one span 11kV line including replacing pin insulators, pin binding, jumpering, replacing insulators cross arms disc, tightening stay, cutting tree branches etc. wherevernecessary, including conveyance of all materials complete. |
| 65 | Disconnecting and lowering down the single phase WP service connection with guy wire from the OH line and reconnecting the same after completing the line work. |
| 66 | Disconnecting and lowering down the three phase WP service connection with guy wire from the OH line and reconnecting the same after completing the line work. |
| 67 | Dismantling (without damage) one 11kV A type pole after disconnecting stays, strut etc. attached thereon and stacking thesame. |
| 68 | Dismantling one damaged 11kV A type pole after disconnecting stays, strut etc. attached thereon and stacking the same. |
| 69 | Dismantling one damaged 11kV PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stackingthe same. |
| 70 | Dismantling (without damage) one 11kV PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking thesame. |
| 71 | Dismantling one damaged 11kV TW/RSJ/Rail pole after disconnecting stays, strut etc. attached thereon and stackingthe same. |
| 72 | Dismantling (without damage) one km 11kV line (three conductors) including dismantling cross arm, insulators, disc,disconnecting jumper connection, rolling the conductor and stacking the materials. |
| 73 | Stringing of one km 11kV line with ACSR Raccoon (3 conductors) after fittinginsulators and giving jumper connections including cutting and removing tree branches wherever necessary excluding cut point works |
| 74 | Additional rate for refitting/redoing one Disc set while renewing any type of11kV cut pole. |
| 75 | Additional rate for providing one disc set, PG clamp etc. complete, on any type of HT pole for making cut point. |
| 76 | Dismantling (without damage) one km LT single phase 2 wire OH line conductor by dismantling cross arms, insulators and stacking the conductors in rolls properly. |
| 77 | Reshackling one span LT three phase 4 wire OH line including pin binding, jumpering, replacing insulators/cross arms/shackle, tightening stay, cutting tree branches etc. wherever necessary including conveyance of all materials. |
| 78 | Reshackling one span LT OH Additional conductor including pin binding, jumpering, replacing insulators/cross arms/shackle, tightening stay, cutting tree branches etc. wherever necessary including conveyance of all materials complete |
| 79 | Transferring LT single phase 2/3 wire OH line to newly erected HT/LT pole including dismantling existing cross arm and insulators, refitting the same on the new pole, binding etc. complete |
| 80 | Transferring LT three phase 4/5 wire OH line to newly erected HT/LT pole including dismantling existing cross arm and insulators, refitting the same on the new pole, binding etc. complete |
| 81 | Dismantling one ordinary street light/CFL/LED fitting from existing pole and refitting the same on newly erected pole including disconnecting and reconnecting wires. |
| 82 | Additional rate for refitting/redoing one Shackle Set, including reshacling one span, while renewing any type of LT pole |
| 83 | Dismantling one Sodium Vapour/Mercury Vapour/Metal Halide lamp fitting from the existing pole and refitting the same on newly erected pole including disconnecting and reconnecting wires (without using aerial lift). |
| 84 | Dismantling (without damage) one LT PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking the same |
| 85 | Dismantling (without damage) one HT stay including digging pit in all classes of soil and backfilling, and bringing back to section store |
| 86 | Renewal of existing damaged/old 11kV Stay with new stay in place including excavation & backfilling of pit, dismantling, refitting of all items and conveyance of all materials |
| 87 | Dismantling (without damage) one Channel cross arm from existing DP structure and bringing back to section store. |
| 88 | Providing barbed wire anti climbing protection (2.5m height) for one 11kV pole. |
| 89 | Fabrication of structures for erecting equipments. The GI & MS angles will be supplied departmentally |
| 90 | Fitting and erecting one HT PSC Single Pole in position, including fitting cross arm, digging and back filling pit in ordinary soil (as per standards), drawing sufficient length of GI earthing leads from F clamp through V cross arm to the ground for earthing (excluding provision of earthing) |
| 91 | Fitting and erecting one HT Double Pole Structure using PSC pole in position including fitting 2 channel cross arms, digging and back filling pit in ordinary soil, drawing sufficient length of GI earthing leads through all cross arms to the ground for earthing (excluding provision of earthing) |
| 92 | Fitting and erecting one HT Double Pole Structure using A type pole in position including fitting 2 No. channel cross arm, digging and back filling pit in ordinary soil, drawing sufficient length of GI earthing leads through all cross arms to the ground for earthing (excluding provision of earthing) |
| 93 | Stringing of one km 3 PH 11kV line with XLPE m 43.49 2300 100027. 00 CONTR Insulated ACSR Raccoon or equivalant (3 conductors) after fitting insulators, binding conductors to pin insulators using suitable tie and anchoring with wedge type anchoring clamps including cutting and removing tree branches wherever necessary excluding cut point works |
| 94 | Providing bridging at Cut points for 3 PH 11kV line with XLPE Insulated ACSR Raccoon or equivalent (1 conductors) using IPC and respective conductors |
| 95 | Renewal of existing damaged/old 11kV PSC/RCC Pole with new PSC pole in place including excavation, erection of new pole, backfilling pit and refitting of all items etc. and conveyance of all materials except pole. |
| 96 | Renewal of existing damaged/old 11kV PSC/RCC Pole with new A type pole in place including excavation, erection of new pole, backfilling pit and refitting of all items etc. and conveyance of all materials except pole |
| 97 | Renewal of existing damaged/old 11kV PSC/RCC Pole with new Four legged lattice structure in place including excavation, erection of new pole, backfilling pit and refitting of all items etc. No 9348.45 5 46742.2 5 CONTR and conveyance of all materials except pole |
| 98 | Renewal of existing damaged/old 11kV TW/RSJ/Rail Pole with new A type pole in place including excavation, erection of new pole, backfilling pit and refitting of all items etc. and conveyance of all materials except pole |
| 99 | Renewal of existing damaged/old 11kV TW/RSJ/Rail Pole with new Four legged lattice structure in place including excavation, erection of new pole, backfilling pit and refitting of all items etc. and conveyance of all materials except pole. |
| 100 | Renewal of existing damaged/old LT Strut of any type with new PSC strut in place including excavation of pit, erection of new strut, backfilling, consolidating, dismantling and refitting of all items and conveyance of all materials except pole |
| 101 | Replacing holder, fused bulb/CFL, changing wires, giving connection etc. of street light including conveyance of all materials. |
| 102 | Dismantling one 1x40W fluorescent tube fitting from the existing pole and refitting the same on newly erected pole including disconnecting and reconnecting wires. |
| 103 | Dismantling (without damage) one AB switch from existing structure and bringing back to section store. |
| 104 | Dismantling one HT pin insulator with pin and bring back to section store |
| 105 | Dismantling bridging at Cut points for 3 PH 11kV line with XLPE Insulated ACSR Raccoo |
| 106 | Dismantling one km LT Sph 3 wire line XLPE Insulated ACSR Rabbit or equivalent, incl. fitting cross arm etc. removing touchings and conveyance of materials. |
| 107 | Erection of tower superstructures above the ground level including erection of normal and special hill side members, wherever necessary, providing insulators, cross arms tower accessories etc for 14m A, B, C type lattice towers, 14 m A poles etc (including fitting cross arms) as per approved drawing and direction of the departmental staff at site |
| 108 | Fitting and erecting 1 No. double pole using 14/12m 'A' type poles in line and level including fixing of angles to connect the two poles by using clamps, bolts & nuts and earthing etc. but excluding cost of materials. |
| 109 | Providing temporary stay during the line stringing work wherever found necessary and as directed. |
| 110 | Stringing of 33 kV, 159 sq mm XLPE Covered Conductor including fitting all accessories( like V cross arms, Channel cross arms, Hardware fittings suitable for 159 Sq.mm Covered Conductor, insulators etc) providing end terminations, midspan joints, Jumpering, Binding to Insulators, Installing insulated piercing connectors, Connecting to LA, Isolator etc. |
| 111 | Dsimantling one km 3 PH 11kV line with XLPE Insulated ACSR Raccoon |
| 112 | Dismantling of suspension clamp suitable for LT AB cable |
| 113 | Dismantling of Anchor clamp / dead end clamp for LT AB cable |
| 114 | Dismantling of 1.1 kV Aerial bunched cable of size 3 x 70 + 1 x 16 (Street Light) + 1 x 50 Sq.mm. (Insulated Messenger) |
| 115 | Dismantling of 1.1 kV Aerial bunched cable of size 3 x 50 + 1 x 35+1x 17 sqmm with bare/insulated Messenger from poles With out damage and stacking |
| 116 | Stringing of 1.1 kV Aerial bunched cable of size 3 x 70 + 1 x 16+1x 50 sqmm with bare/insulated Messenger through existing poles |
| 117 | Stringing of 1.1 kV Aerial bunched cable of size 3 x 50 + 1 x 35 + 1 x 16 sqmm with bare/insulated Messenger through existing poles |
| 118 | Installing One No. 4 way Satellite Connector of size Main :16 to 95, Tap:4 to 35 Sq.mm to the LT AB cable of Standard size |
| 119 | Erection of Anchor clamp / dead end clamp for LT of any size |
| 120 | Erection of suspension clamp for LT ABC of any size |
| 121 | Installation of Pre-insulated straight through joints for 16sqmm cable |
| 122 | Installation of Pre-insulated straight through joints for 50sqmm cable |
| 123 | Installation of Pre-insulated straight through joints for 70sqmm cable |
| 124 | Laying 3 x 300 sq mm 33kV XLPE cables in trench including drawing through pipes wherever necessary. |
| 125 | Doing outdoor/indoor cable termination of 3x300 mm2 33KV XLPE cable very carefully observing directions of manufactures and departmental staff including crimping of socket |
| 126 | Doing straight joint of 3x300 mm2 33KV XLPE cable very carefully observing directions of manufactures and departmental staff including crimping of socket |
| 127 | Mounting one 3x300 mm2 XLPE outdoor cable termination of structures very carefully without causing any E 1651.80 86 4 6607.23 CONTR damage to the drilling holes wherever necessary as directed by the departmental officers |
| 128 | Supply of HDPE Pipe PE 100 (IS 4984/1995), 8kg, 160mm Outer Dia |
| 129 | Dismantling one Transformer (upto and including 160kVA) from existing structure and loading to any vehicle directly, including disconnecting HT/LT/Earth connections. |
| 130 | Erecting one 100kVA Transformer to existing DP and giving connections, including loading from TMR/SRS/other stacking place & unloading at site but excluding cost for transporting transformer. |
| 131 | Dismantling one damaged AB switch from existing structure and bringing back to section store. |
| 132 | Fitting one set AB switch on existing DP, giving connection and drawing sufficient length of GI earthing leads to the ground for earthing, excluding provision of earthing. |
| 133 | Dsimantling one km 3 PH 11kV line with XLPE Insulated ACSR Raccoon |
| 134 | Dismantling one Sodium Vapour/Mercury Vapour/Metal Halide lamp fitting from existing pole, cleaning, rewiring, repairing/replacing holder, tube, bulb, igniter, choke, capacitor etc. and refitting the same in position and giving connection (without using aerial lift) |
| 135 | Laying HDPE pipes (IS : 4984) on land portion including conveying within initial lead and aligning the pipes, electro-fusion welding using automatic or semi automatic electrofusion machines, testing the pipeline thus fabricated to suit the hydraulic working pressure and after testing, aligning the pipeline, lowering the pipe in position into the trenches already made, testing the line to suitable pressure with potable water before back filling and levelling the trenches including all labour charge, hire for appliances etc., complete but excluding cost of pipe and fittings: 110mm Nominal Outer Diameter Pipes. |
| 136 | Loading HT A type pole of all sizes to Hand cart from the stacking place and unloading the same at work site (excluding transportation). |
| 137 | Loading HT PSC pole to Hand cart from the stacking place and unloading the same at work site (excluding transportation). |
| 138 | Loading LT PSC pole to Hand cart from the stacking place and unloading the same at work site (excluding transportation). |
| 139 | Transporting poles by hired vehicle to a distance upto 5km and carrying upto 4 numbers of poles excluding loading& unloading charges. |
| 140 | Transporting poles by hired vehicle to a distance beyond 5km and carrying upto 4 numbers of poles. (Running km |
| 141 | Transporting A type pole of all sizes by Head load- for an average distance of one km where transportation by hand cart is not possible. (normally limited to 0.3km). |
| 142 | Transporting Four legged lattice structure of all sizes by Head load- for an average distance of one km where transportation by hand cart is not possible. (normally E*km limited to 0.3km) |
| 143 | Transporting UG Cable |
| 144 | Transportation of materials issued departmentally for the work from departmental stores and distribution to locations for erection including storage if necessary, loading and unloading charges with lead of 50 m by head load and initial lift of 1.5m at each end etc. - Manual labour for 1km for Insulators and accessories, power conductor accessories and earth conductor accessories etc |
| 145 | Transportation of materials issued departmentally for the work from departmental stores and distribution to locations for erection including storage if necessary, loading and unloading charges with lead of 50 m by head load and initial lift of 1.5m at each end etc. - Manual labour for 1km for Tower extensions and other structures and all other materials including earthing materials |
| 146 | Transporting one HT PSC pole by Head load- for an average distance of one km where transportation by hand cart is not possible. (normally E*km limited to 0.3km). |
| 147 | Transporting one HT TW/RSJ/Rail pole by Head load - for an average distance of one km where transportation by hand cart is not possible. (normally limited to 0.3km). |
| 148 | Transport of materials issued departmentally for the works form departmental stores and distribution to locations for erection including storage if necessary, loading and unloading charges etc as directed by Board staff. from Angamali to Kozhinjampara general area Towers, extensions and other structures and all other materials including earthing materials etc |
| 149 | Clearing touchings on 33kV lines, cutting branches of trees, bamboo clusters, coconut cudjans etc. from above the lines for a distance of 2.0m from the outer conductor as specified by dept. (Rural/Remote). |
| 150 | Felling trees including cutting of trunks and branches completely , without removing root and stacking serviceable materials without damaging private, public, KSEBL properties- Beyond 30cm and upto 60cm girth |
| 151 | Felling trees including cutting of trunks and branches completely, without removing root completely and stacking serviceable materials without damaging private, public, KSEBL properties- Beyond 60cm and upto 120cm girth |
| 152 | Felling trees including cutting of trunks and branches completely , without removing root completely and stacking serviceable materials without damaging private, public, KSEBL properties Beyond 120cm and upto 240cm girth |
| 153 | Providing one Earth using GI No earth pipe of size 38.1mm dia, 2.5m length including digging separate pit (0.45x0.45x2.5m) at a minimum distance of 1.5m away from the pole/structure and maintaining standard distance between different earth pipes in ordinary soil & backfilling. |
| 154 | supply of materials |
| 155 | 33kV XLPE, CCSX 159sqmm, AAAC Covered Conductor |
| 156 | Tension Insulator 33 kV Class Polymeric with special string hardware & accessories |
| 157 | Pin Insulator 33 kV Composite Polymeric |
| 158 | Pre formed metallic cable tie |
| 159 | 33KV Grade, 159sqmm Join Kit |
| 160 | Surge Arrestors Polymeric 30kV Class 1, 10kA |
| 161 | Insulation Piercing Connector (IPC) for connecting Surge Arrestors |
| 162 | Heat shrinkable outdoor termination kit for 33 Kv Covered Conductor Please Enable Macros to View BoQ information |
