|
| 1 | Dismantling roofing including ridges, hips, valleys and gutters etc. and stacking the material within 50 metres lead of 15.25.1 GS Sheet. |
| 2 | Earth work in excavation by mechanical means (Hydraulic Excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m. including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2.8.1 All kinds of soil. |
| 3 | Providing and laying damp-proff course 40mm thick with cement concrete 1:2:4 1cement:2 coarse sand : 4 graded stone aggregate 12.5mm nominal size). |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level: 1:2:4 ( 1 Cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). |
| 5 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. 5.20.1 Thermo-Mechanically treated bar. |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form for (5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 7 | Reinforced cement concrete work in beams, suspended floors, roofs having stope upto 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level upto floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 5.3 (1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size). |
| 8 | Brick work with 1st class common burnt clay F.P.S. (non-modular) bricks in foundation and plinth in: 6.1.1Cement mortar 1:4 (1 cement : 4 coarse sand). |
| 9 | Half brick masonry with 1st class common burnt clay F.P.S. (non-modular) bricks in superstructure above plinth level upto floor V level in: 6.9.2Cement mortar 1 : 4 (1 cement : 4 coarse sand). |
| 10 | 12mm cement plaster of mix1:4 (1cement:4 coarse sand). |
| 11 | Repairing to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints & preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead. 14.1.1) With cement mortar 1:4 (1 cement : 4 fine sand). |
| 12 | Steel work in built up tubular (round, square or rectangular tubes etc.) trusses etc., including cutting. hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc. complete. 10.16.3 Electric resistance or induction butt welded tubes. |
| 13 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required In grating, frames, guard bar, railing, brackets, gates and similar works. |
| 14 | Providing and fixing pre-coated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self-drilling itself tapping screws ot size (5.5x 55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with: 12.46.2 Pre-coated galvanised iron profilo sheets 0.40 mm thick. |
| 15 | Providing and fixing pre-coated galvanised steel sheet roofing accessories , Zinc coating 120gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self-drilling/ self-tapping screws or with polymer coated J or L hooks, bolts and nuts and or C.I. seam bolts and nuts, G.l. plain and bitumen washers complete: Ridges Plain (500-600mm) 12.47.1.2 Pre-coated galvanised iron profile sheets 0.40 mm thick. |
| 16 | Providing and fixing pre-coated galvanised steel sheet roofing accessories , Zinc coating 120gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self-drilling/ self-tapping screws or with polymer coated J or L hooks, bolts and nuts and or C.I. seam bolts and nuts, G.l. plain and bitumen washers complete: Gutter (600 mm over all girth) 12.47.6.2 Pre-coated galvanised iron profile sheets 0.40 mm thick. |
| 17 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.13.63.3 with water thinnable cement primer on wall surface having VOC less than 50grams /litres. |
| 18 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. 13.43.1 Two or more coats on new work. |
| 19 | Finishing wall with Acrylic smooth exterior paint of required shade :- New work ( Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing. |
| 20 | Providing wood work in frames of doors, windows, clerestory windows and other frames. Wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately. 9.1.3) Local best quality Tolhao wood. |
| 21 | Providing & fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling or panelled or panelled and glazed shutters 25 mm to 40 mm thick: 9.5.1 Local best quality Teak wood. |
| 22 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. |
| 23 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 x 600 mm. |
| 24 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in alt colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (I cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 25 | Cement concrete flooring 1:2:4 (I cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.11.2.140mm thick with 20mm nominal size stone aggregate. |
| 26 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand :6 graded stone 20 mm nominal size over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 27 | Add EPF @ 3.25% |
| 28 | Add CESS @ 1% |
| 29 | Add GST @ 18.00% Please Enable Macros to View BoQ information |
