|
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 2 | M/L for Virified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed inwhite or coloured cement to match, including 15mm thick screed bed in CM 1:6 laying floor finishesed complete all as specified and directed. |
| 3 | . --Ditto-- all as per above but as in skirting over & including 10mm thick backing coat of CM 1:4 all as specified. |
| 4 | S&F Non Skid (coloured) ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over & including 15 mm thick screed bed in cement mortar (1:6) complete all as specifed and as directed. |
| 5 | S&F glazed ceramic coloured tiles (300mmx 450mmx7 mm) in vertical surfaces jointed in neat cement slurry and pointed in white cement. Incl cutting the tiles to the required size whereven required incl mitring the corners etc over 10 mm thick backing coats of cement plaster in CM (1:4) complete all as specified and directed. |
| 6 | Taking down aluminium door/ windows incl frames and complete fittings of area exc 1.50 sqm but n. exc 4 sqm complete. |
| 7 | M&L for Powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.29mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below middle/lock rail and 5mm thick tinted glass above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and incl mortice lock with duplicate keys etc complete all as specified and directed approved by Engr-In-Charge including supply and fixing the following items:(a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf.(b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf(c) Powder Coated Aluminium Handles 150 mm - 2 nos per leafMake (Aluminium Sections) : Jindal/Valco/Galco/Hindalco or equivalent as approved by Engr-In-Charge |
| 8 | Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified. |
| 9 | S & F solid PVC door frames of size 50x47mm made out of 5mm plain colour PVC sheet supplying and fixing in opening as per specification and drawing shown in SSR complete all as specified and as directed. As approved by Accepting Officer |
| 10 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification incl the fwg S & F As approved by Accepting Officer(a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 Nos per leaf(b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf |
| 11 | Dismantling wrought iron or mild steel work of any description not othervise provided for |
| 12 | S&F Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165 |
| 13 | S&F MS hollow rectangular/square/circular tubes/pipes of YST 310 Grade as in frame work for roofs/rafters/purlins/chajjas/trusses/ columns/ struts etc and like similar items etc. complete all as specified |
| 14 | M&L for mild steel framed work as in doors or gates of angle Gde-Fe-290( Gde-E-165) or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete |
| 15 | M&L for preparation of new surfaces of steel of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide complete. |
| 16 | Dismantling of plain or corrugated steel sheets in roof coverings any type complete all as specified & directed by Engineer in charge. |
| 17 | S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting, 0.50 mm thick, of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed. |
| 18 | S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 19 | S & F Steel ventilator with top hung shutter including hinges, steel peg stay, complete as specified complete all as specified and directed. |
| 20 | Dismantling wall and ceiling boarding of any description, thickness including cover fillets complete al as specified and directed. |
| 21 | M&L Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions all as specified and directed |
| 22 | S&F for Anodised aluminium snap grid of size of grid 605 x 605mm frame work for false ceiling all as specified and directed. Note :- (i) Main tee, cross tee shall be 35x25x1.5mm & 25x25x1.5mm respectively. Angle at end all along the walls shall be 40x25x2mm. (ii) Rate quoted by the contractor shall deemed to inclusive of frame work complete. |
| 23 | S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified |
| 24 | S & F for Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete . |
| 25 | S & F in repair Ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to dia of pipe 20mm as in repairs complete all as specified and directed. |
| 26 | Supply & Fixing in repair chromium plated shower rose 125mm round shape fancy type fixed to 15mm bore pipe all as specified and directed by Engr-in-charge. |
| 27 | S & F in repair Angular Stop Cock, CP, fency type with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete fixed as in repair in all respect all as specified. |
| 28 | S & F in repair Bib taps, CP, fency type long nose with wall flanage screwed for 15mm bore of iron pipe or for brass ferrule and fixed in position complete fixed as in repair in all respect all as specified.Make : Jaquar / Hindware / Cera / Prayag or equivalent as approved by Engr-In-Charge |
| 29 | Supply & Fixing in repair Brass CP wall Mixer 3 in 1 System with provision for overhead and hand shower suitable 15mm bore of pipe complete all as specified and directed. |
| 30 | Supplying and laying in repair of CPVC pipes 16mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified including taking down or up existing GI tubing & connections all as specified and directed by Engr-in-Charge. |
| 31 | Supplying and laying in repair of CPVC pipes 20mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified including taking down or up existing GI tubing & connections all as specified and directed by Engr-in-Charge. |
| 32 | Supply & Fixing in repair stainless steel Towel Rack with lower hanger size 24'' (600 mm) fixed to walls with hook etc. |
| 33 | S & F in repair Vitreous china premium/1st quality wash basin (under counter), white, size 550x400 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified including all Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, Make : Hindware / Parryware/Cera or equivalent as approved by Engr-In-ChargeNote : The items for counter will be measured and paid separately. |
| 34 | Supply and fixing in repair of fancy type pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shank supply and fixing ly nuts for iron pipe of 15mm bore fancy type. |
| 35 | S & F in repair Flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified.Make : Hindware / Parryware/Cera or equivalent as approved by Engr-In-Charge |
| 36 | S & F in repair Vitreous china premium/1st quality urinal bowl type of white colour, of size 330x300x450mm incl providing and fixing plugs/brackets, bedding urinal against wall in CM 1:2, securing urinals to plugs with and incl S&F of all accessories for fixing as recommended by manufacturer like 60mm long brass secrews/fasteners/rag bolts etc, pointing urinal back in white cement; connecting for disCharge pipe incl necessary packing, union complete all as specified.Make : Hindware/Parryware/Cera/Jaquar as approved by Engr-In-Charge |
| 37 | S&F in repairs Tubular towel rail brass chromium plated 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete. |
| 38 | S&F in repairs CP Cockroch trap (127x127mm) with waste holw as per cat no FT-25 make Prayag including taking out old one and setting new one in CM 1:3 complete |
| 39 | S & F PVC mirror cabinet of size 300x450mm of selected quality glass fixed in PVC cabinet all as specified and directed. |
| 40 | M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement etc complete, fixed in repair. |
| 41 | M&L for machine cut Granite (of any type) t 20mm thick for kitchen platform over and including bedded and jointed with grey cement slurry/backing coat 15 mm thick in CM (1:6) and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types |
| 42 | M & L for Rounding to edges of stone slabs on edge, such as in steps, cooking platform, and other similar situations |
| 43 | S & F in repair Vitreous china squatting pan of Orissa patten size 580 x 440 white colour including CI S/P trap long size as directed joint run and lead front or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in repair complete and making good to floor in PCC 1:2:4 all as directed and specified. Make : Cera / Parryware / Hindware or equivalent as approved by Engr-In-Charge |
| 44 | Demolition and breaking up drain PVC(SWR) pipes single socketed in any length with rubber joints all as specified |
| 45 | PVC (SWR) pipes single socketed, in any length with rubber ring joints, as in floors or fixed to walls 75 mm bore |
| 46 | PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or fixed to walls 110 mm bore |
| 47 | PVC (SWR) bends any radius 75 mm bore |
| 48 | PVC (SWR) bends any radius 110 mm bore |
| 49 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. |
| 50 | M & L for Cement plastering 15mm( thick in two layers -first layer 10mm thick with ready mix plaster and outer layer 5mm thick ready mix water proof plaster) on outer walls by adding potable water by weight of material as mentioned by manufacture ready mix plaster shall comply with IS- 1661-1972, IS-2402-1963, IS- 2250-1981 and shall confirm 28 days compressive strength 10-15 MPA, bulk density 1600-1800 kg/M and pull out bond strength->0.5 MPA complete all as specified and directed |
| 51 | M&L for preparation of new plastered surfaces on walls, chajjas,filling of hair line cracks with white cement and applying two coats of 100% anti fungal weather resistant acrylic paint over a coat of acrylic primer in approved shade and as per manufacturer's instructions including necessary scaffolding complete all as specified and as directed. |
| 52 | Complete removal of existing water proofing treatment incl bedding if any n exc. 50mm thick etc. on any type of roof, cleaning with wire brushers etc. and removal of debris out side MD land complete all as specified and directed. |
| 53 | M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate for levelling course for consolidated thickness shall be varied from 40 mm as per the requirements all as directed by Engr-in-Charge. |
| 54 | M&L for 10mm thick screed plaster on roof for laying in CM 1:4 waterproofing treatment, with using WPC (WPC will be measured and paid separately as supply only) |
| 55 | Supply only integral Waterproofing compound. |
| 56 | M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt not less than 150 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltr/Sqm by forced and sealing all the over laps of 75 mm in length side and 100 mm on the width side of membrane all as speficied and directed. |
| 57 | Demolition of plain cement concrete (Un reinforced) in benching and surface channels,bedding etc. below or above ground level. |
| 58 | Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar as in concrete bed, haunching set in cement mortar of 150 mm Dia complete all as specified. |
| 59 | Excavation in trenches n.exc 1.5m deep and n.exc 1.5m wide in manholes,etc. and getting out any type of Soil complete all as specified. |
| 60 | M&L for plain cement concrete 1:4:8 Type D2 using 40mm graded aggregateas in foundation, filling in mass concrete for manholes & drains. |
| 61 | M&L for plain Cement concrete 1:2:4 Type B1 using 20 mm graded aggregate as in benching and surface channel of Manholes. |
| 62 | M&L for plain cement concrete 1:3:6 Type C1 using 20mm graded aggregate as in coping including form work etc complete. |
| 63 | Demolition of stone masonry built in cement or cement lime mortar all as specified and directed. |
| 64 | M&L for squared rubble walling, Jodhpur type brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed. |
| 65 | M&L for squared rubble walling, Jodhpur type brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed. but except stone |
| 66 | M&L for squared rubble walling, brought upto coursed Jodhpur type well bonded bedded laid dry complete |
| 67 | Ditto as above but except stone complete. |
| 68 | Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified & directed by Engineer-in-Charge. |
| 69 | M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement incl, forms mould, mi-tred/stopped ends etc. |
| 70 | M&L for rendering 15mm thick in CM 1:4 on stone masonary sufaces including finished even and smooth using extra cement. |
| 71 | M&L for reinforced concrete pipes class NP-2 ,150 mm dia laid and jointed complete with collars and including demolition and breaking up Existing SGSW/RCC pipes concrete bed including packing under and haunching jointed in cement mortar and taking out of trenches if required etc, complete all as specifed and directed. |
| 72 | supply only water proofing compound |
| 73 | M&L for Concrete bed to drain pipes including packing under haunching against the sides of pipe after they are laid and tested; in cement concrete 1:4:8 type D-2 for 150mm dia pipe |
| 74 | M&L for reinforced concrete NP2 drain pipes 200 mm Dia pipes confirming to IS laid in trenches and jointed in CM 1:2 all as specified & directed by EIC |
| 75 | M&L for Concrete bed to drain pipes including packing under haunching against the sides of pipe after they are laid and tested; in cement concrete 1:4:8 type D-2 for 200mm dia pipe |
| 76 | M & L for cutting in to existing manhole for connectiing new drain 150 mm bore , making good to pipe & rendering cutting out existing benching for & forming branch channel in cement concrete ( 1:2:4) type B1 smooth finished & reforming benching as requierd. |
| 77 | Returning filling in soil including spreading, levelling and well ramming in layers n.exc 25cm thick in layer etc all complete. |
| 78 | Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point |
| 79 | Dismantaling Stone slabs and tiles of any description or thickness in floors, aprons etc. |
| 80 | M&L for jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted, set, jointed and grouted in lime mortar 1:3 or cement mortar 1:6 complete complete all as specified and as directed by the Engineer-in-Charge |
| 81 | M&L for 5cm thick Sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc.n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4. completecomplete all as specified and as directed by the Engineer-in-Charge |
| 82 | Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removal of rubbish/ demolished materials out of MD land complete all as specified and directed. |
| 83 | M&L for 100mm thick PCC ype D-2, 1:4:8 using 40mm graded stone aggregate as in sub bases all as specified. |
| 84 | Providing and laying Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors With grey pigment cement and pigments including 20 mm thick screed in cement mortar (1:6) over and pointed complete all as specified. |
| 85 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified. |
| 86 | Taking down carefully aluminium point wiring any type ,surface/concealed/ PVC capping or tubing ( including light,fan,s/socket, or power)complete fittings such as switches,ceiling rose,pendents,regulators,sockets etc complete |
| 87 | Taking down old unserviceable main switch board, DB of any type and any capacity from its location with accessories MCCB's/MCB/SP/SPN/TPN cpmplete. |
| 88 | Taking down old unserviceable tube light/cfl light/recessed mlounted lighht of any type of light fittings complete all as directed. |
| 89 | Taking down and refixing ceiling fan/air circulating fan with cleaning & paingting of ceiling fan complete with two coat of syntthetic enamel paint of white colur by sparying including filling cavities with filler complete all as specified by E-in-charge after minor repairs |
| 90 | Taking down and refixing exhaust fan with cleaning & painting of exhaust fan complete with synthetic two coat of enamel paint of black colour by sparying including filling cavities with filler complete all as directed by E-in-Charge after minor repair. |
| 91 | M & L for point wiring with two single core 1.5 Sqmm cabel (nominal area) stranded copper conductor, PVC insulated unsheathed FRLSH cable, 1100 V grade, conforming IS:694 & colour code in conduit system of wiring, drawn in and including concealed rigid PVC Conduit not less than 20 mm dia with galvanised modular metal flush box, thickness as per OEM suitable of suitabe size and modular white cover plate with frame of suitale module and wiring to be terminated in pressed steel sunken boxes including all accessories fixed with chromium plated screws and washers and using single core 1.5 Sqmm (nominal area) stranded copper conductor, PVC insulated unheated FRLSH cable as in earth wire (green colour) connecteedd to common earth only complete all as specified and directed for following:- (a) One light, C/Fan, E/Fan, bell point controlled by one switch. |
| 92 | (b) All as per item no. 4 above here in before but with copper conductor cable of size 1.5 Sqmm for one 3 pin socket outlet, 5 amp on same board. |
| 93 | (c) All as per item no. 4 above here in before but with copper conductor cabe of size 2.5 Sqmm for one 3 pin socket outlet, 5 amp on independent board. |
| 94 | All as per item no. 4 above here in before but with copper conductor cabe of size 4 Sqmm for one 3 pin socket outlet, 16 amp on independent board. |
| 95 | S & F for Modular switch, flush button, 1 way, 6A, 1 module, complete as specified and directed by Engineer- in- charge. |
| 96 | M & L For modular socket outlet 2/3pin, 2 module, 6Amps, 230 Volts AC, complete all as specified and directed by Engineer-in-charge. |
| 97 | M & L For modular socket outlet 2 in 1, 6 pin, 2 module, 6/16Amps, 230 Volts AC, complete all as specified and directed by Engineer-in-charge. |
| 98 | S & F for Modular switch, flush button, 1 way, 16A, 1 module, complete as specified and directed by Engineer- in- charge. |
| 99 | S & F ceiling rose surface backlite 65x50mm 3 terminals complete. |
| 100 | Supply and fix in repair LED tube light fitting capacity 20 watt fixed on wall/surface / ceiling with all accessories tube,driver,with surge protector completerewired with multistranded copper cable & connecting to ceiling rose with 3 core ,multistranded flexible copper cable including taking out existing one u/s. |
| 101 | Supply and fix in repair LED tube light fitting(mirror type) capacity 10 watt fixed on wall/surface / ceiling with all accessories tube,driver,with surge protector completerewired with multistranded copper cable & connecting to ceiling rose with 3 core ,multistranded flexible copper cable including taking out existing u/s. |
| 102 | M&L in repair Modular white cover plate with frame ( both inner & outer plate cover) 3 module |
| 103 | M&L in repair Modular white cover plate with frame ( both inner & outer plate cover) 8 module |
| 104 | Supply, fix, connecting and testing factory made, MCB distribution board (MCB DB), IP 38, SPN, 8 way, 415 Volts, flush type made out of 1.2mm thick CRCA sheet metal, Phosphatised, duly powder coated and conforming to IS 13032 with 200 Amps rated bus bar, neutral link, earth bar and din rail etc. complete fixed in switch board/ wall complete all as specified and directed. Note: MCBs shall be measured and paid separately. |
| 105 | S&F MCB SPN 40 A rating 240 V, 10KA, C series fixing in DB's including connecting with bottle type copper thimble complete all as specified and directed by Engr-in-Charge |
| 106 | S&F connecting and testing MCB Single pole (MCB SP) 6-32 Amps , 240 Volts of rupturing capacity 10 KA, C Curve type including taking out existing u/s one complete all as specified and directed. |
| 107 | S & F in repair 15 Watt LED Bldg security light with a nominal system . The luminaire housing should be made of pressure die cast aluminimum. The total power consumption should not exceed 15W (including driver) pre wired fitted on and including two Nos PVC block of suitable l size and connection up to tube light fitting with connecting up with copper 3 core flexible cord of minimum size 0.5 Sqmm size and testing complete including LED lamp, including taking down old unserviceable fitting any type complete all as specified and as directed. |
| 108 | Earthing with galvanised iron earth plate electrode 600 x 600 mm & 6 mm thick burried directly in ground (earth pit not less than 2.25 metre deep below normal GL) with top of earth plate not less than 1.5 metre below GL connected to GI earth lead wire 4 mm dia connected to earth plate electrode by means of GI nuts, bolts & washers earth wire protected with & including 15 mm dia medium grade ISI marked GI pipe not less than 7.5 metre long all as shown in electrical plate No. 3 MES Schedule Part 1, with & including ; PCC 1:3:6 B1 reinforced with welded steel wire fabric not less than 4 Kg per Sq M, watering arrangements with 20 mm GI medium grade pipe ISI marked , GI funnel with GI mesh, filling with mixture of common salt & charcoal, necessary excavation and earth works in any type of soil, including test point, testing & commissioning, complete. (Note :- GI earth wire with GI pipe protection beyond 7.5 metre measured & paid separatelyand it includes taking down old existing earthing.) including taking out existing u/s earthing. |
| 109 | Excavation in trenches not exc 1.5 mtr wide and n.exc 1.5 mtr in deep and getting out in Hard/Dense soil laying of cables etc. |
| 110 | Returning filling in including spreading, leveling watering and well ramming in layers n.exc 25cm thick using excavated soil |
| 111 | Removing excavated surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5mtr above from the starting point |
| 112 | Supply and laying Jodhpur stone patti for cable protection of lenth between 55 to 60 cm but width between 25 to 30 cm thicknes not less than 5 cm complete as per site requirement incl removing old unsv patti and direction of engineer in charge. |
| 113 | Supply and spread approved dry river sand for foundations/Cable duct including watering and consolidation, cushioning of cable laid in trenches complete all as directed by Engineer-in-Charge Note:- Punned thickness will be measured for payment purpose |
| 114 | Supplying and laying GI pipe Light grade (ISI marked) 50mm bore with connecting accessories, laid under road/ drain/fixed on wall etc for protection of cables complete all as specified and directed |
| 115 | Supply and laying & testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of the under mentioned type and sizes complete all as specified and directed (a) 10 Sqmm x 2 core Please Enable Macros to View BoQ information |
