|
| 1 | Part (A) BuildingEarth work in excavation in foundation, trenches manholes, road side chambers etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe / foundation and disposal of surplus excavated material at a lead up to 50 m suitable site as per direction of Engineer for following depths, below natural ground / Road top level. In all type soils such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc. depth up to 1.5m. |
| 2 | Dismantling of existing structures like culverts, bridges, retaining walls, CC road and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 50 metres as directed by Engineer.Cement Concrete Grade M-15 and above and PCC blocks |
| 3 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 4 | Carriage of Materials by mechanical transport including loading, unloading and stacking : EARTH 5KM |
| 5 | Random rubble masonry with hard stone in foundation and plinth. Cement mortar 1:6(1 cement : 6 coarse sand) |
| 6 | Extra for random rubble masonry with hard stone in superstructure above plinth level and upto two stories. |
| 7 | Centring and shuttering with plywood or steel sheet upto two stories ( each story of height upto 3.5 metre from floor level) including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete |
| 8 | Suspended floors, roofs, landings, balconies and access platform |
| 9 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 10 | Reinforcement for R.C.C work at all levels including straightening cutting , bending , placing in position and binding all complete. Cold twisted bars. |
| 11 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level :1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 12 | Brick work with FPS bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 13 | Half brick masonry with brick of class designation 75 in foundations and plinth in : cement mortar 1: 4 (1 cement : 4 coarse sand) |
| 14 | Providing and fixing horizontal chajja of stone 40 mm thick and upto 80 cm projection in cement mortar 1:4 (1 cement : 4 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade: Red sand stone |
| 15 | Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 20 mm cement plaster of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar1:6 (1 cement : 6 fine/ coarse sand) |
| 16 | Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 12 mm cement plaster of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar1:4 (1 cement : 4 fine/ coarse sand) |
| 17 | Random rubble dry stone Kharanja (soling) under floor. |
| 18 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:1½:3 (1 Cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). |
| 19 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded 20mm nominal size stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar40mm thick |
| 20 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.South (Red) Above 3601 Cm2 Slabs |
| 21 | Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite Work |
| 22 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 23 | Providing and fixing 1st quality MAT finished ceramic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 24 | & F 1st quality Vitrified Porcelain Polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufacture) with water absorption less than 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1 : 4 including grouting the joints with white cement and matching pigment etc complete.Size 600 mm X 600 mm |
| 25 | Precast terrazzo tiles 20mm thick with graded marble chips of size upto 12mm laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete with precast tiles on 20mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Light shade using white cement |
| 26 | Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges :Sand or other approved stone 50mm thick |
| 27 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 28 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : Old work (one or more coats) |
| 29 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 30 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) : With float glass panes of 5.50 mm thickness |
| 31 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 32 | Providing and fixing False Ceiling Tiles of approved materials of size 595x595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections ( galvanized @ 170 gsm/sqm.) consisting of main \\"T\\" runner suitably spaced at joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200mm center to center and cross \\"T\\" of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main \\"T\\" at 600mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats fixed to ceiling with 6 mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanised level clips spaced at 1200m center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-Charge. (The rate is excluding cost of tiles which will be paid separately ). |
| 33 | Providing and fixing Stone jali 40mm thick Red/Pink sand stone throughout in cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali patterns to be cut square to jali slab without any chamfers etc: |
| 34 | Kota stone slab flooring 25mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :Area of each slab 900 to 2000 sqcm |
| 35 | Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.80mm thick with zinc coating not less than 275gm/m² |
| 36 | Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.80mm thick with zinc coating not less than 275gm/m² |
| 37 | Part (B) Sanitary Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. |
| 38 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps. |
| 39 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 40 | Providing and Fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. internal work-exposed on wall 15mm diameter nominal bore. |
| 41 | 20mm diameter nominal bore. |
| 42 | 25 mm dia. nominal bore |
| 43 | Providing and Fixing C.P. brass long nose bib cock of approved quality confirming to IS standard and weighting not less than 690gms. 15mm nominal |
| 44 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore. |
| 45 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore |
| 46 | Providing and fixing PTMT bib cock of approved quality and colour 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 47 | 15 mm nominal bore, 122mm long. Weighing not less than 99 gms |
| 48 | 15 mm nominal bore, 165mm long. Weighing not less than 110 gms. |
| 49 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe :- 32 mm dia |
| 50 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 51 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements. Weighing not less than 106 gms. |
| 52 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. :- 450MM long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170gms. |
| 53 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design:500 litres capacity. |
| 54 | Brass full way valve with C.I. wheel (screwed end) 25 mm dia |
| 55 | Brass full way valve with C.I. wheel (screwed end) 32 mm dia |
| 56 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in-charge. Internal work - Exposed on wall15 mm nominal outer dia .Pipes |
| 57 | 20 mm nominal outer dia .Pipes. |
| 58 | 25 mm nominal outer dia .Pipes |
| 59 | 32 mm nominal outer dia .Pipes. |
| 60 | Providing, lowering, laying in trenches, aligning, fixing in position and jointing socketed rubber gasket type ISI marked uPVC pipes of Class III (6 Kg/sqcm) suitable for potable water with rubber ring joints (as per IS 4985-2000) of following outer dia with all accessories (excluding specials) complete including all material, labour, hydraulic testing and commissioning as per Technical Specifications and as per direction of Engineer. Note : E/w to be measured and paid separately.110 mm dia |
| 61 | 125mm dia |
| 62 | Double/Single socketed 90 degree long bend (single piece welded with socket) :- 110 mm dia |
| 63 | 125mm dia |
| 64 | Double/Single socketed 45/22.5/11.25degree long bend (single piece welded with socket)110 mm dia |
| 65 | 125mm dia |
| 66 | uPVC End Cap110 mm dia |
| 67 | 125mm dia |
| 68 | Center table glassCENTRE TABLE - Size- (L)1100mmx(D)600mmx(H)440mmSupplying and placing in position of Waiting Room center table as per photograph.Center Table glass shall be10- 12mm thick toug+B46hened, edge beveled and in rectangular shaped. Another glass attached with chrome plated metal rods with UV welding and using as a bookshelf. The product should be from BIFMA certified company. |
| 69 | Side Tables Size 2'-2' |
| 70 | Non revolving Visitor ChairVisitor Chair shall be of dimensions (560mm W x 670mm D x 1020 mm H ) Seat & Back Assembly : The seat & back shall be made of 12 mm thick hot-pressed plywood upholstered with Mesh type fabric cover & moulded polyurethane foam. The polyurethane foam density shall be of 45+/-2 kg/m3, The back foam shall be designed with contour lumber support for extra cushioning, Under structure shall be of MS elliptical/oblong pipe (40x20x1mm thick) chrome plated frame. All work complete including Fabrication, nailing, screwing, pasting, transporting, loading, unloading, placing, finishing, setting, etc complete in all due respect as per technical specifications, standards, directions and satisfaction of Engineer Incharge. |
| 71 | Sofa set Single seater SOFA SET Providing and placing of Sofa's with Seat Height of 450mm. Slab stock foam with density 60+/-2Kg/m3 at seats and cushions. Seats and Cushion is also provided with 100% hollow recron fillers for extra comfort. Sofa structure consists of Tropical 12mm ply frame at the bottom on which S-Springs and Tie bars are provided then the complete structure is provided with layers of Non woven fabric, 2 Layers of Slab Stock Foam 80-100mm and finally recron is assembled together to form the final sofa. Seat and Cushions is upholstered with PVC Leatherite (shade should be approved from buyer) upholstery, Spring assembly of 4mm Dia is mounted in understructure for support and additonal cushioning purpose. Legs shall be provided made of Stainless Steel (Grade SS 202). It is a welded assembly made by the combination of Tube and Plate. |
| 72 | Sofa set02 seater SOFA SET Providing and placing of Sofa's with Seat Height of 450mm. Slab stock foam with density 60+/-2Kg/m3 at seats and cushions. Seats and Cushion is also provided with 100% hollow recron fillers for extra comfort. Sofa structure consists of Tropical 12mm ply frame at the bottom on which S-Springs and Tie bars are provided then the complete structure is provided with layers of Non woven fabric, 2 Layers of Slab Stock Foam 80-100mm and finally recron is assembled together to form the final sofa. Seat and Cushions is upholstered with PVC Leatherite (shade should be approved from buyer) upholstery, Spring assembly of 4mm Dia is mounted in understructure for support and additonal cushioning purpose. Legs shall be provided made of Stainless Steel (Grade SS 202). It is a welded assembly made by the combination of Tube and Plate. |
| 73 | Sofa set03 seater SOFA SET Providing and placing of Sofa's with Seat Height of 450mm. Slab stock foam with density 60+/-2Kg/m3 at seats and cushions. Seats and Cushion is also provided with 100% hollow recron fillers for extra comfort. Sofa structure consists of Tropical 12mm ply frame at the bottom on which S-Springs and Tie bars are provided then the complete structure is provided with layers of Non woven fabric, 2 Layers of Slab Stock Foam 80-100mm and finally recron is assembled together to form the final sofa. Seat and Cushions is upholstered with PVC Leatherite (shade should be approved from buyer) upholstery, Spring assembly of 4mm Dia is mounted in understructure for support and additonal cushioning purpose. Legs shall be provided made of Stainless Steel (Grade SS 202). It is a welded assembly made by the combination of Tube and Plate. |
| 74 | Providing and fixing storage unit in Librarary sizes of 600 mm deep and 2100 (h), made out of 18mm thk. Plyboard and back made up of 8mm ply, unit is provided with vertical and horizontal divisions as per design with drawers and shutters, lockable, with all hardware like hinges, tower bolt, magnetics catcher, lock of approved quality. The cabinet shoould be raised 75/100mm above ground. Inside exposed surfaces should be finished with putty , wood primer coats and finished with 3 coats of oil base colour paint with specified shade. exposed outside surfaces should be Teak wood finished laminated (Golden Wange) with standard grade laminate of approved design and make. all exposed edges should be finished with first quality T.W. beadings of same finish (Golden Wange) to be finished with malemine polish as per design and specifications and instructions given by interior designer & as per drawing. Please Enable Macros to View BoQ information |
