|
| 1 | Material and labour for Collecting of drinking water sample all as directed by Engineer-in-charge, handling and transportation of samples to NABL accredited laboratory as approved by authorities ,carrying out the analysis of PH value, total alkalinity, aluminium, total residual chlorine, TDS, turbidity complete as per latest IS of swimming pool waterfor the following Note:- i)The Rate deemed to include collecting of samples and transportation to lab . ii) The testing and analysis of water collected and its transportation is considered as one job. iii) The contractor shall submit the test report of water samples once in a month. |
| 2 | Swimming pool |
| 3 | Diving pool |
| 4 | URU swimming pool |
| 5 | Material and Labour for opening and servicing/overhauling the monoblock pumpset of following capacity, greasing and replacing the worn-out gland rope, studs, nuts, bolts, washers ,air releasing valve,rubber gasket ,metal filling and balancing the shaft, checking winding insulation resistance etc complete all as specified and as directed at site. |
| 6 | 10 HP pumpset |
| 7 | 7.5 HP pumpset |
| 8 | Supply only aluminium sulphate (Inorganic soluble powder, non-ferric) for swimming pool water treatment complete all as specified and directed. |
| 9 | Supply only calcium hypochlorite 65-70% purity Chlorine Granules disinfectant for water treatment complete all as specified and directed. |
| 10 | Supply only sodium hypochlorite solution as disinfectant agent complete all as specified and as directed. |
| 11 | Supply only bleaching powder commercial Grade 1 superior quality around the pools/pump houses complete all as specified and directed. |
| 12 | Supply only soda ash for swimming pool water as pH stabiliser complete all as specified and as directed. |
| 13 | Supply only copper sulphate powder as disinfectant agent complete all as specified and as directed.Make:- As approved by E-in-C branch / confirming to generic BIS specification as approved by GE.Note for item No.03 to 08:- The contractor has to bring' chemicals in batches as intimated by Engineer-in-Charge not in a single batch. |
| 14 | Material and Labour to carryout the suction sweeping of cadets swimming pool and diving pool for removing the sediment slits/dirt and cleaning the walls, over flow channel, and channel grills etc complete all as specified and as directed for the following.Note:- Sweeping shall be carried out once in a week. In special case, due to un-hygienic conditions, the frequency of sweeping to be increased as directed by Engineer in charge. |
| 15 | Swimming pool (50x20x2m) |
| 16 | Diving pool (18x18x6m) |
| 17 | URU swimming pool (20x10x2m) |
| 18 | Material and Labour in replacement of old unserviceable deep leaf net of medium size with 5 Mtr Extension handle complete all as specified and directed. |
| 19 | Material and Labour in replacement of old unserviceable Algae brush with 3 mtr handle complete all as specified and directed. |
| 20 | Material and Labour for Dismantling the Electrical connection from monoblock pumpset, taking out the burnt motor of following capacity from beds ,transporting to civil work shop , opening the motor and removing the burnt/old defective winding carefully cleaning the inner parts, rewinding the motor with same gauge supper enamelled copper wire of good insulation, varnishing, heating/drying and reassembling the motor and transporting to site , refixing on the existing beds ,connecting the electrical connection ,testing and commissioning for the following all as directed. |
| 21 | 10 HP pumpset |
| 22 | 7.5 HP pumpset |
| 23 | 3 HP pumpset |
| 24 | Material and Labour for replacement of bearings of 3 phase, monoblock pumpset of following capacity by disconnection of electric cable from the terminal box of pump set, remove the pump set from the foundation bed and transport to authorised work shop, decoupling rotor/impeller shaft from pump set, dismantling worn out ball bearing - 2 no, remitting the shaft by lathe work and welding work for correct alignment for fixing of bearing, replacement of ball bearing - 2 Nos, reassembling of pumpset after replacing bearings and replacement of gland rope, water seal, bushes, Transporting the pump set to the site re-fixing on foundation channel with new bolts and nuts, apply grease and connecting electrical connections and testing |
| 25 | 10 HP pumpset |
| 26 | 7.5 HP pumpset |
| 27 | 3 HP pumpset |
| 28 | Supply and replacement of old unserviceable PVC Flexible Vacuum hose pipe of size 50mm dia complete all as specified and directed. |
| 29 | Supply and replacement of old unserviceable Stainless steel Suction sweeping brush vacuum Head, 36 inch made out of SS 304 with 50mm hose collar complete all as specified and directed. |
| 30 | Material and labour for preparing the surface by scrapping with wire brush and emery paper and painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of existing shade including writing MES NO of size 2.5cm height and length depend upon number of letters 'Outgoing' and 'Incoming' electric supply, marking the water flow direction for the following equipment's all as directed at site and as specified. |
| 31 | Monoblock pump set 10 HP/7.5 HP |
| 32 | Panel boards of size 2mx1.5mx0.5M |
| 33 | Cu-Ag dual ionization plant |
| 34 | Material and labour for Cleaning of Swimming pool of size 50mx20mx2m by acid solution complete all as specified and directed. |
| 35 | Material and labour for Cleaning of Diving pool of size 18mx18mx6m by acid solution complete all as specified and directed. |
| 36 | Material and labour for Cleaning of URU Swimming pool of size 20mx10mx2m by acid solution complete all as specified and directed. |
| 37 | Material and Labour for re-fill Chlorine test kit with coloured sample complete with all testing fitment and 100 ml residual chlorine reagent-1 (RC-1) in rexine finish wooden box/rexin box confirming to IS specification complete all as specified and directed. |
| 38 | Supply and fixing in replacement of old unserviceable centric Butterfly Valves of Class PN-1.6 and of following sizes to be fixed on the Pressure filters/PVC Pipe lines etc by taking down the existing unserviceable Butterfly valves complete all as specified and directed by the Engineer-in-Charge for the following:- |
| 39 | 200mm Bore |
| 40 | 150mm Bore |
| 41 | 100mm Bore |
| 42 | 80mm Bore |
| 43 | 65mm Bore |
| 44 | 50mm Bore |
| 45 | Supply & fix in replacement of old unserviceable UPVC pipes, Class-5, 10 Kg/Cm2 on open/wall as specified by Engineer-In-Charge for the following:- |
| 46 | 110 mm dia |
| 47 | 160 mm dia |
| 48 | 200mm dia |
| 49 | Material and Labour for drain out/pumping mud settled inside the sump by using suction pump and removing the dirts, sediments, silts etc from the bottom and wall inside the sumps /reservoir. Cleaning the surface using wire brush, bleaching powder and other cleaning materials as required. Applying one coat of lime wash inside and acrylic emulsion paint on outside surface of the following capacity of sump/reservoir including writing the details of sump, capacity, date of cleaning and due date out side visible place by using enamel paint of suitable colour on black background including complete all as directed Note :- 1. The contractor shall make his own arrangement for electrical backup supply incase of any power failure 2. The contractor has to get approval from Engr-In-Charge after cleaning the surfaces before applying white wash of inside walls. 3. The contractor has to handover sumps after cleaning with in the time period as directed by Engr-In-Charge,In case of failure an amount of Rs. 3000/- per hour will be deducted. 4. The undermentioned sumps has to be cleaned as directed by Engineer-In-Charge |
| 50 | RL-30/RL-92 of storage capacity 3,10,000 Ltrs |
| 51 | RL-127(S4) of storage capacity 7,50,000 Ltrs |
| 52 | RL 146(S2) of storage capacity 14,00,000 Ltrs |
| 53 | RL 197(S3) of storage capacity 13,00,000 Ltrs |
| 54 | Filtration plant treated water sump of storage capacity 5,00,000 Ltrs |
| 55 | Filteration plant FF sump of storage capacity 3,00,000 Ltrs |
| 56 | RL 80 (S5) of storage capacity 2,00,000 Ltrs |
| 57 | Sump Near Well No-02/Fighter sqdn sump of storage capacity 1,00,000 Ltrs |
| 58 | Sumps Near Eagle squadron/Vatika Pond - 2 NoSupply and Fixire station of storage capacity 50,000 Ltrs |
| 59 | Near light house of storage capacity 40,000 Ltrs |
| 60 | Material and Labour for Drain out water from apprx 3 Mtr dia of shallow well by means of pumping out water up to bottom level up to not more than 10 mtr depth from ground level , removing dirts, sediments ,silts and mud etc from bottom, cleaning of bottom and side walls of inside with wire brush for cleaning the way of holes/pores for maintain natural spring including spraying required quantity of bleaching powder and applying one coat of acrylic emulsion paint on outside surface upto 1 mtr height above ground level complete all as specified and as directed. |
| 61 | Material and Labour for Drain out water from apprx 8 Mtr dia of well by means of pumping out water up to bottom level approx 8 mtr depth from ground level , removing dirts, sediments ,silts and mud etc from bottom ,cleaning of bottom and side walls of inside with wire brush for cleaning the way of holes/porous for maintain natural spring including spraying required quantity of bleaching powder complete all as specified and directed. |
| 62 | Material and Labour for cleaning of moolasthan well (approximate size of 25mx 16mx3m depth) by draining out water from well by means of pumping out water up to bottom level approx 3 mtr depth from ground level, removing dirts, sediments, silts, alagae and mud etc from bottom by using manually, cleaning of bottom and side walls of inside with wire brush for cleaning the way of holes/porous to maintain natural spring including spraying required quantity of bleaching powder complete all as specified and as directed. |
| 63 | Material and labour for removing vegetation around the wells/ sumps/pump houses including cutting of tree branches complete all as specified and directed by Engineer-In-Charge.Note:- The rate quoted is deemed to include cutting tools etc. |
| 64 | Supply and Fix Nylon net as per the sample for covering top of well including remove the old net complete all as specified and directed. |
| 65 | Material and Labour for removing of old damaged sign board and Supply and fix acrylic new acrylic sign board of size 1.0mx0.75m along with necessary supports and steel poles with 50mm dia for fixing complete all as specified and directed by Engineer-In-Charge.Note:- The contractor shall write the installation name and installed capacity in white colour with blue back ground complete all as specified and directed. |
| 66 | Material and Labour for servicing of heavy duty chlorine/Alum/Lime dosing system, 25 LPH, 10 kg/cm2 including repairs to 0.5 HP, 1440 RPM, 3 phase induction motor if required, replacement of gear oil, PVC NRVs, clearing blockage, testing with necessary CPVC piping arrangement not more than 1.5 mtrs complete all as specified and as directed by Engineer-In-Charge. |
| 67 | Supply and Fix in replacement of main transformer suitable for CU-AG ionisation unit of following capacity including taking down old unserviceable item complete all as specified and directed by the Engineer-in-Charge. |
| 68 | 2 LLPH |
| 69 | 1 LLPH |
| 70 | 0.5 LLPH |
| 71 | Supply and Fix in replacement of drive transformer suitable for CU-AG ionisation unit of capacity 2 LLPH, 1 LLPH & 0.5 LLPH including taking down old unserviceable item complete all as specified and directed by the Engineer-in-Charge. |
| 72 | Material and Labour for scrapping & painting of one coat of primer and two coats of epoxy paint of suitable colour on wire mesh/angle irons fitted on 3 mtr dia wells complete all as specified and as directed by Engineer-In-Charge. |
| 73 | Supply and Fix in replacement of old u/s round submersible 3 core copper conductor PVC insulated and PVC sheathed cable of size 6 Sqmm complete all as specified and directed by Engineer-in-Charge. |
| 74 | Supply and Fix in replacement of old U/s digital voltmeter/Ammeter/MFM in existing LT panels complete all as specified and directed by Engineer-In-Charge. |
| 75 | Supply and Fix in replacement of old u/s MCCBs 415V, 16 KA, 4 Pole,63A-100A variable thermal setting complete all as specified and directed. |
| 76 | Supply and Fix in replacement FASD (Fully Automatic Star Delta starter) 3 phase 415 Volts 50 Hz relay range 9-14A including taking down old material complete all as specified and directed by Engineer-in-Charge. |
| 77 | Supply and Fix DOL starter (Direct on line) 3 phase 415 Volts 50 Hzsuitable for 7.5HP Monoblock pumpset and relay range 13-22A complete all as specified and directed by Engineer-in-Charge. |
| 78 | Supply and Fix in repair LT control cable of copper conductor, XLPE insulated, PVC innersheathed, armoured 1100 V grage of 6 core 1.5 sqmm complete all as specified and directed. |
| 79 | Supply and Fix in repair copper conductor cable of 1100V grade, PVC insulated, round sheathed (flexible) un-armoured industrial cable of size 70Sqmm x 3 core with proper saddles & lugs complete all as specified and as directed by Engineer-in-charge |
| 80 | Material and Labour for Cleaning of internal walls of fiber glass and polyester resin pressure filters at Swimming pool of size 2 mtr dia and 1.5 mtr height of capacity 125000ltrs/hrs after removing the filter media by brushing with nylon brush and using bleaching powder and cleaning of existing pipe holes complete all as directed by Engineer in -charge.NOTE: The quoted is deemed to be inclusive for removal of the old filter media from filter, cleaning the filter and clearance of unusable media from site The media will be measured and paid separately under relevant items. |
| 81 | Supply and Fix in replacement of unserviceable manifold arm assembly lateral set 3/4\\" consists of laterals in length 225mm, 160mm, extends 100mm and bushes suitable to existing 2.5 kg/cm2 astral pool make sand filter of 2 mtr dia complete all as specified and as directed. Note : The contractor has to brought laterals same as exisitng sample provided by Engineer-In-Charge |
| 82 | Material and Labour for filling filter media sand of size 1-2 mm in the pressure filters complete all as specified and directed by Engineer in -charge. |
| 83 | Material and Labour for filling filter media sand of size 0.4-0.8mm mm in the pressure filters complete all as specified and directed by Engineer in -charge. |
| 84 | Material and Labour for filling pebbles in sand filters as support media complete all as specified and as directed Note for Item No. 43 to 45 : Rate quoted is for filling the media in pressure filters of Swimming pool Please Enable Macros to View BoQ information |
