|
| 1 | Providing,laying, jointing and testing Gl pipe confirming to ISI specification i/c commissioning complete in all respect of following dia in distribution (earth work in trenches shall be measured and paid for separately) including all leads and lifts as per the direction & satisfaction of E-in-charge with butt welding. |
| 2 | 100 mm dia (M) |
| 3 | Cutting of MS pipe complete in all respect with all leads and lifts as per the satisfaction of E-in-charge. |
| 4 | GI Pipe 100 mm dia |
| 5 | Welding of MS. pipe with circumferential butt welding joint welded sockets at both end with double/ triple layer as per IS 816-1965(according to wall thickness of pipes) The work shall be done as per entire satisfaction of Engineer-in-Charge within all leads and lifts. |
| 6 | GI Pipe 100 mm dia |
| 7 | Providing and fixing double flanged cast steel aluice valve of Kirloskar/KSB/ Leader make and of class-150 for rising main and capable of with standing normal seat pressure as per relevant IS specifications with upto date amendments including rubber, gaskets, nuts and bolts complete in all respect and to thte entire statisfaction of Engineer-in Charge (100 mm dia) |
| 8 | Providing, welding, and fixing M.S. plate flanges of various dia (nominal bore) of following Flange tables confirming to IS 6392-1971 or latest with up to date amendments after every 100 m pipe or as per site requirement including cutting of pipes wherever required, welding in three layers (leak proof) confirming to specifications as prescribed in relevant I.S. Code Le. IS 816-1969 or latest as applicable with up to date amendments with nuts, bolts and washers and specials etc. confirming to IS-1963 or latest with up to date amendments including packing sheet i.e. asbestos fibre sheet minimum 3 mm thick and painting with anticorrosive paints complete in all respects in all leads, lifts and carriage of material at site and as directed by Engineer-In-Charge. (100 mm dia Table-5) |
| 9 | Excavation in foundation, trenches etc. earth work in all type of soil such as pick work, jumper work, blasting work kankar, moorum singles including decomposed soft and hard rock etc. upto all heights stacking the excavated earth not more than 3 metres clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinths and sides of foundation etc.consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth upto all leads and lifts as directed by the Engineer in charge complete in all respects. |
| 10 | Providing and laying cement concrete 1:4:8 (1 cement: 4 sand: 8 graded stone aggregate 40mm nominal size) excluding cost of centring & shuttering in. Foundation and Plinth |
| 11 | Providing and laying cement concrete 1:14:3 (1) cement: 1½ sand: 3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in.: Foundation and plinth |
| 12 | Providing and laying cement conc 1:5:10 (1 cement 5 sand,10 graded aggregate water bone aggregate 40mm nominal size)with 15% plum and curring complete excluding cost of formwork in retaning walls brest wall, the size of plum shall usually be 150mm to 300mm as per H.P.W.D specification with in all lead and lift and as per direction and satisfaction of Engineer in charge. |
| 13 | Providing form work with steel plates 3.15mm thick welded with angle iron 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden batten and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4 metres and removal of the same for insitu reinforced concrete & plain conrete work in. |
| 14 | Vertical surfaces such as walls (any thickness) partition and the like including attached pillasters, buttresses, plinth and string courses and the like. |
| 15 | Providing mild steel/tor steel reinforcement for RCC work including bending, binding and placing in position complete upto floor two level. |
| 16 | Providing fixing including cutting, hoisting, fixing, in position and applying a priming coat of red lead paint including all lead and lift and as per direction and satisfaction of Engineer in charge. 1-Section of Size ISMB 150 |
| 17 | Providing, supplying, transporting to site, erecting and fixing 25 mm dia 7×19 construction galvanized steel wire rope suspension cable of approved make conforming to relevant IS specifications, complete with all accessories such as turn buckles, wire rope thimbles, U-clamps, shackles, eye bolts, anchor plates, saddles and other fittings as required for supporting 100 mm dia G.I. pipeline (Medium Class) across khads, ravines or other crossings, including stretching, tensioning, fixing in position, testing and commissioning complete in all respects as per the directions of the Engineer-in-Charge.The rate includes carriage of all materials to site, labour, tools and plants, handling, loading/unloading and all incidental charges complete. Please Enable Macros to View BoQ information |
