Tender For Repair / Painting Of Steel Furniture And Repair / Polishing Of Wooden Furniture At Bso Avadi Under Ge Avadi, Avadi-Tamil Nadu

TDR : 55961600

Tender Notice
BOQ

19 Days Left

Avadi , Tamil Nadu

Tender Brief : Tender For Repair / Painting Of Steel Furniture And Repair / Polishing Of Wooden Furniture At Bso Avadi Under Ge Avadi

Document Fees
₹ 500 /-

EMD
₹ 78000.0 /-

Tender Value
₹ 39 Lakhs /-

Submission Date
02-07-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Repair / painting of steel furniture
2	REWEAVING OF CHAIR VARANDAH WITH CANE PLASTIC (DRG NO.FD-19, FD-256):-
3	Removing of existing old unserviceable cane plastic from chair verandah and reweaving the same with new cane plastic (white colour) 6mm width of approved quality including painting with synthetic enamel paint white all as shown on drawing.
4	REPAIRS TO CHAIR VERANDAH FOR THE FOLLOWING (DRG NO.FD/MAP-II/06):-
5	SEATRemoving of old unserviceable PVC seat from from its existing position and replace the same with new PVC seat 4mm thick and grooves 90X10mm 10 Nos on seat. Make: of PVC sheet : Brite/Cello/Supreme/Neel Kamal/AMKO
6	BACKRemoving of old unserviceable PVC back from from its existing position and replace the same with new PVC back 4mm thick. Make: of PVC sheet : Brite/Cello/Supreme/Neel Kamal/AMKO
7	HARD RUBBERRemoving of old hard rubber unserviceable hard rubber from from its existing position and replace the same with new hard rubber all as shown on drawing.
8	PAINTINGS OF CHAIR VERANDAH M&L after removing of existing old worn out paint by any means with proper treatment from chair verandah and applying spray painting two coats with synthetiic enamel white paint over a coat of red oxide primer complete all as dircted and shown on drawings.
9	REPAIRS TO TEAPOY VERANDAH FOR THE FOLLOWING (DRG NO.FD-35, FD-383, FD-208):-
10	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (Exterior grade) Grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick well seasoned second class hard wood beading allround the edging provide middle stiffener at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.
11	HARD RUBBER SHOERemoving of each decayed hard rubber shoe from its existing position of Teapoy Verandah (FD-35, FD-283, FD-208), Chair CB Steel with arm (FD-75M), Chair CB without arm (FD-75M) and replace the same with new hard rubber shoe all as shown on drawing and directed by Engineer-in-Charge.
12	PAINTING TO TEAPOY VERANDAHM&L for applying two coats of synthetic enamel (white) paint with spray gun to frame of teapoy verandah including preparation of surfaces complete all as specified and directed.
13	REPAIR TO ALMIRAH LARGE AND MEDIUM STEEL FOR THE FOLLOWING (DRG NO.FD-67, FD-1032, FD-1033, FD-1031, FD-1034)
14	LEGSS&F for new leg made out from MS sheet 1.6mm thick and applying one coat of red oxide zinc chrome primer over two coats of synthetic enamel paint with spray painting by the spray gun after removing of each old worn out legs from its existing portion of Almirah large steel with shelves and Almirah medium steel with shelves and replace the same complete all as specified and directed and as shown on drawing.
15	HANDLESS&F for new handle made out from mild steel over chromium plated of size 150mm size and weight of each handle should not be less than 185gm of existing pattern after removing of old unserviceable / broken handle from its existing position of almirah large steel with shelves and almirah medium steel with shelves and replace same complete all as specified and directed and as shown on drawing.
16	LOCKSS&F for new brass, six lever (Make : Godrej) lock with steel CP duplicate keys, weight of each lock should not be less than 260gm after removing of old unserviceable lock from its existing position of almirah large steel with shelves and almirah medium steel with shelves and replace same complete all as specified and directed and as shown on drawing.
17	SHELVES FOR ALMIRAH LARGE STEEL WITH SHALVES (DrgNo. FD-67(M), FD-1031 & FD-1032).S&F for new shelf made out of MS Sheets of 1.00mm thick and applying one coat of red oxide zinc chrome primer over two coats of synthetic enamel paint with spray painting by spray gun after removing of old worn out shelf from its existing portion of almirah large steel with shelves and replace same complete all as specified and directed and as shown of drawing.
18	SHELVES FOR ALMIRAH MEDIUM STEEL WITH SHALVES (DrgNo. FD-67(M), FD-1031 & FD-1032).S&F for new shelf made out of MS Sheets of 1.00mm thick and applying one coat of red oxide zinc chrome primer over two coats of synthetic enamel paint with spray painting by spray gun after removing of old worn out shelf from its existing portion of almirah medium steel with shelves and replace same complete all as specified and directed and as shown of drawing.
19	PAINTINGS OF ALMIRAH LARGE STEEL WITH SHALVES (DrgNo. FD-67(M), FD-1031 & FD-1032).M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from almirah large steel with shelves complete all as directed shown drawings.
20	PAINTINGS OF ALMIRAH MEDIUM STEEL WITH SHALVES (DrgNo. FD-67(M), FD-1031 & FD-1032).M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from almirah medium steel with shelves complete all as directed shown drawings.
21	PAINTINGS OF BOOK SHELF OPEN LARGE STEEL (Drg No.FD-69)M & L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from book self open large steel complete all as directed shown drawings.
22	PAINTINGS OF BOOK SHELF OPEN SMALL STEEL (Drg No.FD-69)M & L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from book self open small steel complete all as directed shown drawings.
23	PAINTINGS OF TABLE OFFICE CLERK STEEL (Drg No.FD-84)M & L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from Table office clerk steel complete all as directed shown drawings.
24	PAINTINGS OF CHAIR CB STEEL WITH ARMS [Drg No.FD-75(M)]M & L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from Chair CB steel with arm complete all as directed shown drawings.
25	PAINTINGS OF CHAIR CB STEEL WITHOUT ARMS [Drg No.FD-75(M)]M & L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from Chair CB steel without arms complete all as directed shown drawings.
26	PAINTINGS OF LOCKER STEEL (GE/BKP/02/07)M & L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from Locker steel complete all as directed shown drawings.
27	REPAIR TO CHARPOY GI PIPE FOR THE FOLLOWING DRG NO : FD220)
28	LEGSM&L 32mm bore (medium grade) GI tubing leg (ISI marked) of charpoy after removing of old unserviceable leg of charpoy GI pipe from its existing position all as shown on drawing.
29	LONG RAILM&L 32mm bore (medium grade) GI tubing of long rail (ISI marked) size of 1884 mm long of charpoy GI after removing of old unserviceable long rails of charpoy GI pipe from its existing position all as shown on drawing cut to required length of and threading at both ends all as shown on drawing.
30	SHORT RAILM&L 32mm bore (medium grade) GI tubing of short rail (ISI marked) cut to required length of 900mm long and threading at both ends all as shown on drawing.
31	ELBOW GIM&L 32mm bore 3 way GI elbow weight of each GI elbow should not less than 480gms as per ISI specification all as shown on drawing.
32	CHECK NUTS&F for check nut for fixing the top with charpoy GI all as shown on drawing.
33	MIDDLE STIFFENERRemoving of old unserviceable stiffener from its existing position and replace the same with new stiffener made out of 25mm GI pipe (medium grade) 900mm long all as specified and shown on drawing.
34	PLY TOP 12MM THICKS&F 12mm thick ply BWR grade, type BB, both sides commercial ply wood (7 Nos ply) with 6mm thick well seasoned teak wood duly polished found at round the edging of the top and beading required 4mm dia 65mm long counter shank machine nut, bolt, washer on top including removing of existing top all as directed by Engineer in charge. Make of Ply wood : Archid/Greenply/National ply/Kit ply as approved
35	REPAIRS TO CHAIR CB STEEL WITH ARMS FOR THE FOLLOWING [DRG NO.FD-75(M)]
36	WOODEN FRAME SEATS&F of canned with wooden seat frame made out from well seasoned teak wood duly canned as per Godrej pattern with new plastic cane of 2mm to 2.5mm wide half round oval shape for caning and 4mm wide of half round oval shape cane for bedding & applying two coats of black polish after removing of unserviceable /decayed seat frame from existing portion from chair CB steel with arm as replaced all as directed and shown on drawing.
37	WOODEN FRAME BACKS&F of canned with wooden back frame made out from well seasoned teak wood duly canned as per Godrej pattern with new plastic cane of 2mm to 2.5mm wide half round oval shape for caning and 4mm wide of half round oval shape cane for bedding & applying two coats of black polish after removing of unserviceable /decayed back frame from existing portion from chair CB steel with arm as replaced all as directed and shown on drawing.
38	WOODEN ARM FOR CHAIR CB STEEL WITH ARMSS&F the new arm made out from well seasoned teak wood and apply two coats of black polish including removing broken arm from its existing portion of chair CB steels with arm all as directed and shown on drawing.
39	STIFFENER FOR CHAIR CB STEEL WITH ARMS&F with new MS flat of stiffener size 520mmx15mmx4mm by welding including two coats of synthetic (Olive Green) paint over one coat of red oxide zinc chrome primer including removing of old worm out MS cleat from its existing position from chair CB steel with arm complete all as directed and shown on drawing.
40	REPAIRS TO CHAIR CB STEEL WITH OUT ARMS FOR THE FOLLOWING [DRG NO.FD-75(M)]
41	WOODEN FRAME SEAT FOR CHAIR CB STEEL WITHOUT ARMS&F for canned with wooden seat frame made out from well seasoned teak wood duly canned as per Godrej pattern with new plastic cane of 2mm to 2.5mm wide half round oval shape for caning and 4mm wide of half round oval shape cane for bedding & applying two coats of black polish after removing of unserviceable /decayed seat frame from existing portion from chair CB steel without arm as replaced all as directed and shown on drawing.
42	WOODEN FRAME BACK FOR CHAIR CB STEEL WITHOUT ARMS&F for canned with wooden seat frame made out from well seasoned teak wood duly canned as per Godrej pattern with new plastic cane of 2mm to 2.5mm wide half round oval shape for caning and 4mm wide of half round oval shape cane for bedding & applying two coats of black polish after removing of unserviceable /decayed back frame from existing portion from chair CB steel without arm as replaced all as directed and shown on drawing.
43	STIFFENER FOR CHAIR CB STEEL WITHOUT ARMS&F for new MS flat of stiffener size 420mmx15mm x4mm by welding including two coats of synthetic (Olive Green) paint over one coat of red oxide zinc chrome primer including removing of old worm out MS cleat from its existing position from chair CB steel without arm complete all as directed and shown on drawing.
44	REPAIRS TO COMPUTER CHAIR / REVOLVING CHAIR WITH ARMS FOR THE FOLLOWING (DRG NO.TP & FD/E6/MAP/01):-
45	WHEELRemoving of old unserviceable revolving wheel from its existing position of computer chair and revolving chair and replace the same by supplying and fixing with revolving wheel PVC 40mm.to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.
46	HYDRAULIC SYSTEMRemoving of old unserviceable hydraulic system from its existing position of computer chair and revolving chair and replace the same by supplying and fixing with new hydraulic system to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.
47	BASERemoving of old unserviceable base from its existing position of computer chair and revolving chair and replace the same by supplying and fixing with new base to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.
48	SEATRemoving of old unserviceable seat from its existing position of computer chair and revolving chair and replace the same by supplying and fixing with new seat to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.
49	BACKRemoving of old unserviceable back from its existing position of computer chair and revolving chair and replace the same by supplying and fixing with new back to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.
50	ARMSRemoving of old unserviceablearms from its existing position of computer chair and revolving chair and replace the same by supplying and fixing with new back to make completely functional rest all as shown on drawing or directed by Engineer-in-charge.
51	REPAIRS TO BOOK CASE STEEL FOR THE FOLLOWING (DRG NO. FD-1028):-
52	SHUTTERRemoving of old unserviceable shutter from its existing position of book case steel and replace the same with new shutter as shown on drawing or directed by Engineer-in-charge.
53	SHUTTER GLASSRemoving of old unserviceable shutter glass from its existing position of book case steel and replace the same with new shutter glass as shown on drawing or directed by Engineer-in-charge.
54	HANDLE Removing of old unserviceable handle from its existing position of book case steel and replace the same with new handle as shown on drawing or directed by Engineer-in-charge.
55	LOCK Removing of old unserviceable lock from its existing position of book case steel and replace the same with new lock 6 lever brass all as shown on drawing or directed by Engineer-in-charge. Make : Godrej/Link marked as approved.
56	PAINTINGS OF BOOK CASE STEEL (Drg No. FD-1028)M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from book case steel complete all as directed shown drawings.
57	REPAIRS TO TABLE OFFICE CLERK STEEL FOR THE FOLLOWING (DRG NOFD-84, FD-381, FD-1004):-
58	LEGRemoving of old unserviceable leg from its existing position and replace the same with new leg made out of MS square pipe 25mm 16 gauge all as shown on drawing.
59	DRAWERRemoving of old unserviceable drawer from its existing position and replace the same with new drawer made out of 20 gauge MS sheet all as shown on drawing.
60	LOCK & KEYSRemoving of old unserviceable lock of table office clerk steel and supplying and fixing with new brass six lever Godrej pattern lock with steel CP duplicate keys all as shown on drawing. (Make : Godrej/Link as approved.)
61	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18mm thick veenered particle board (exterior grade), grade-I quality, with commercial veeners on both sides with 1.00mm thick plastic laminated sheet (Plain & wood grain)pasted over particle board with approved synthetic resin adhesive with 6mm thick well seasoned second class hard wood beading alround the edging all as shown on drawing. (Make of ply wood : Century/Greenply/National ply/Kit ply as approved)
62	REPAIRS TO TABLE OFFICE OFFICER STEEL FOR THE FOLLOWING (DRG NO.FD-84, FD-1003):-
63	LEGRemoving of old unserviceable leg from its existing position and replace the same with new leg made out of MS square pipe 25mm 16 gauge all as shown on drawing.
64	DRAWERRemoving of old unserviceable drawer from its existing position and replace the same with new drawer made out of 20 gauge MS sheet all as shown on drawing.
65	LOCK & KEYSRemoving of old unserviceable lock of table office clerk steel and supplying and fixing with new brass six lever Godrej pattern lock with steel CP duplicate keys all as shown on drawing. Make : Godrej/Link as approved.
66	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18mm thick veenered particle board exterior grade with commercial veeners on both sides with 1.00mm thick plastic laminated sheet (Plain & wood grain) pasted over particle board with approved synthetic resin adhesive with 6mm thick well seasoned second class hard wood beading alround the edging all as shown on drawing. Make of particle board : Century ply/ Greenply/National ply/Kit ply as approved.
67	PAINTINGS OF TABLE OFFICE OFFICER STEEL (Drg No. FD-84, FD-1003)M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from table office officer steel complete all as directed shown drawings.
68	REPAIRS TO LOCKER STEEL FOR THE FOLLOWING (FD-257& GE/BKP/02/07):-
69	LEGSM&L after removing of each old worn out legs from its existing position of locker steel and replace the same by supplying and fixing with new leg made out from MS sheet 1.6mm thick and applying one coat of red oxide zinc chrome primer over two coats of synthetic enamel paint with spray painting, complete all as specified & directed and as shown on drawing.
70	HINGESRemoving of old unserviceable hinges from its existing position and replace the same with new hinges all as shown on drawing.
71	HANDLESS&F for 100mm long aluminium handle of existing pattern after removing of old unserviceable / broken handle from its exisiting position of locker steel complete all as directed.
72	HASP & STAPLES&F for 75mm long hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with steel wood screws.
73	HANGING RODRemoving old broken hanging rod from its existing position and replace the same with new hanging rod made out from 20mm external dia aluminium anodized conduit with a pair of sockets all as shown on drawing.
74	REPAIRS TO TABLE DINING ORS STEEL FOR THE FOLLOWING (DRG NO.FD-165):-
75	LEGRemoving of old unserviceable leg from its existing position and replace the same with new leg made out of MS square pipe 25mm 16 gauge all as shown on drawing.
76	TOPRemoving of decayed top from its existing position and replace the same with new top made out from 18mm thick veneered particle board (exterior grade), Grade-I quality, with commercial veneers on both sides with 1.00mm thick plastic laminated sheet (Plain & wood grain) pasted over particleboard with approved synthetic resin adhesive with 6mm thick well seasoned 1st class hard wood(Teak/Seasam) beading all-round the edging all as shown on drawing. Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved.
77	PAINTING OF TABLE DINING OR STEEL (Drg No.FD-165)M&L for applying spray painting two coats with synthetic enamel (Olive Green) paint internally and externally by spray gun after removing of existing old worn out paint by any means with proper treatment from table dinning ORs steel complete all as directed shown on drawings.
78	REPAIRS TO CHAIR SCHOOL WITH HAND BOARD FOR THE FOLLOWING (DRG NO.FD/E6/MAP/05):-
79	SEAT & BACKRemoving of old unserviceable seat & back from its existing position and replace the same with new seat & back made out of blow plast or equilant approved by E-in-C's Branch all as shown on drawing.
80	HAND BOARDRemoving of old unserviceable hand board from its existing and replace the same with new hand board made out from 18mm thick pre laminated particle board exterior grade-1 hinged at right hand side of chair arm screwed to 25mm dia MS pipe inserted in 20mm dia MS rod welded to frame . Standard PVC edging 1.6mm thick shall be provided all-round the hand board, rest all as shown in drawing.
81	BASKET (JALI)Removing of old unserviceable steel basket (Jali) from its existing position and replace the same with new basket (Jali) made of 5mm MS rod all as speficied and shown on drawing.
82	REPAIRS TO CHARPOY IP HARD TOP FOR THE FOLLOWING (DRG NO: FD/MAP-II/01)
83	TOPRemoving of old unserviceable top from its existing position and replace the same with new top of 12 mm thick BWR grade both sides commercial plywood (seven Nos of ply) complete all as shown on drawing as directed by Engineer-in-Charge.(Make of Plywood : Century ply/Green ply/National ply/ Kitply as approved)
84	PAINTINGS OF CHARPOY IP HARD TOPM & L for applying spray painting two coats with Black paint by spray gun after removing of existing old worn out paint by any means with proper treatment from Charpoy IP hard top complete all as directed shown drawings.
85	REPAIRS TO TABLE BED SIDE STEEL FOR THE FOLLOWING (DRG NO.FD/E6/MAP/15(R):-
86	TOPRemoving of old unserviceable top from its existing position and replace the same with new top made out of 18mm thick prelaminate particle board ext gde one side decorative finish shade and other side white balancing lamination as speciified. Standard PVC edging 1.6mm thick shall be provided alround the top all as shown on drawing.
87	BACKRemoving of old unserviceable back from its existing position and replace the same with new back made out of 6mm thick commercial plywood as per IS-303 all as shown on drawing
88	DRAWERRemoving of old unserviceable drawer from its existing position and replace the same with new drawer.Side and back of drawer shall be made out from 12mm thick commercialplywoodas per IS-303 .Bottom of drawer shall be provided with 6mm thick commercial plywoodmovement onteak wood runners. rest al as shown on drawing
89	HANDLE Removing of old unserviceable handle from its existing position and replace the same with new handleof aluminium anodized all as shown on drawing.
90	Repair / polishing of wooden furniture
91	REPAIRS TO BED WITH PLY TOP FOR THE FOLLOWING (DRG No.FD-246):-
92	HEAD BOARDRemoving decayed head board from its existing position and replace the same with new head board of overall size 900 x 610mm, frame made out from well seasoned 1st class hard wood (Teak/Seasam) batten 75mm x 22mm thick with soft wood (chair batten 03 Nos board), 4mm thick one side teak face BWR grade, type BB Ply wood (three Nos of ply) and other side commercial to be provided on both sides of the head board covering the soft wood batten, 12mm dia half cut teak wood beading shall be provided to join the ply wood and Hollock wood frame all as Shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved).
93	FOOT BOARDRemoving decayed foot board from its existing position and replace the same with new foot board of overall size 900mm long and 300mm height, frame made out from well seasoned 1st class hard wood (Teak/Seasam) batten 75mm x 22mm thick with soft wood (chair batten 03 Nos board), 4mm thick one side teak face BWR grade, type BB Ply wood (three Nos of ply) and other side commercial to be provided on both sides of the foot board covering the soft wood batten, 12mm dia half cut teak wood beading shall be provided to join the ply wood and Hollock wood frame all as Shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved).
94	LONG RAILRemoving of each decayed long rail from its existing position and replace the same with new well seasoned 1st class hard wood (Teak/Seasam) long rail of size 95mmx35mmx1980mm long rounded one edges or face made out from well seasoned wood all as shown on drawing.
95	SHORT RAILRemoving of each decayed short rail from its existing position and replace the same with new well seasoned 1st class hard wood (Teak/Seasam) short rail of size 95mmx35mmx900mm short rounded one edges or face made out from well seasoned wood all as shown on drawing.
96	STIFFNERRemoving of each decayed stiffner from its existing position and replace the same with new well seasoned 1st class hard wood (Teak/Seasam) stiffner of size 60mmx40mmx880mm long rounded one edges or face made out from well seasoned wood all as shown on drawing.
97	MS FLAT IRON STIFFNERRemoving old MS stiffener from hard bed and replace the same with MS flat iron of size 35mmx5mmx150mm, bent at right angle at four corner all as shown on drawing.
98	TOPRemoving decayed/wornout top from its existing position and replace the same with new plywood made out from 12mm thick plywood (seven Nos of ply), BWR grade, type BB fixed to wooden rails with screws all as shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved).
99	POLISHING TO BED WITH PLY TOP Removal of old existing worn out polish from exposed portion of wooden surface by any means of bed with ply top including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge .
100	REPAIRS TO CHAIR DINING FOR THE FOLLOWING (DRG No.FD-16(M), FD-279):-
101	FRONT LEGRemoving of each decayed front leg from its existing position and replace the same with new front leg made out from well seasoned1st class hard wood (Teak/Seasam) all as shown on drawing.
102	REAR LEGRemoving of each decayed rear leg from its existing position and replace the same with new rear leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
103	FRONT RAILRemoving of each decayed front rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.
104	REAR RAILRemoving of each decayed rear rail from its existing position and replace the same with new rear rail made out from well seasoned1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing
105	SIDE RAILRemoving of each decayed side rail from its existing position and replace the same with new side rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing .
106	REAR STIFFNERRemoving of each decayed rear stiffener from its existing position and replace the same with new rear stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
107	STIFFNERRemoving of each decayed stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
108	HARD RUBBER/PVC RINGRemoving of each decayed hard rubber/PVC ring from its existing position of chair dinning (FD-161M, FD-279), Chair writing (FD-280), Chair Easy (FD-281), FD-229) and replace the same with new hard rubber/PVC ring all as shown on drawing and directed by Engineer-in-Charge.
109	POLISHING TO CHAIR DININGRemoval of old existing worn out polish from exposed portion of wooden surface by any means of chair dinning including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
110	REPAIR TO CHAIR WRITING FOR THE FOLLOWING (DRG No.FD-280 ):-
111	FRONT LEGRemoving of each decayed front leg from its existing position and replace the same with new front leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
112	REAR LEGRemoving of each decayed rear leg from its existing position and replace the same with new rear leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
113	FRONT RAILRemoving of each decayed front rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.
114	REAR RAILRemoving of each decayed rear rail from its existing position and replace the same with new rear rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.
115	SIDE RAILRemoving of each decayed side rail from its existing position and replace the same with new side rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.
116	REAR STIFFNERRemoving of each decayed rear stiffner from its existing position and replace the same with new rear stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
117	STIFFENERRemoving of each decayed stiffner from its existing position and replacae the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
118	ARMRemoving of each decayed arm from its existing position and replace the same with new arm made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
119	POLISHING CHAIR WRITINGRemoval of old existing worn out polish from exposed portion of wooden surface by any means of chair writing including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous making, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
120	REPAIRS TO CHAIR EASY FOR THE FOLLOWING (DRG NO.FD-281, FD-229):-
121	FRONT LEGRemoving of each decayed front leg from its existing position and replace the same with new front leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
122	REAR LEGRemoving of each decayed rear leg from its existing position and replace the same with new rear leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
123	FRONT RAILRemoving of each decayed front rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.
124	REAR RAILRemoving of each decayed rear rail from its existing position and replace the same with new rear rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.
125	SIDE RAILRemoving of each decayed side rail from its existing position and replace the same with new side rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.
126	ARMRemoving of each decayed arm from its existing position and replace the same with new arm made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
127	POLISHING TO CHAIR EASY Removal of old existing worn out polish from exposed portion of wooden surface by any means of chair easy including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with sheelac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-charge.
128	REPAIRS TO CHAIR WBB W/O ARM FOR THE FOLLOWING [DRG NO. FD-56(M), FD-225, FD-285]:-
129	FRONT LEGRemoving of each decayed front leg from its existing position and replace the same with new front leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
130	REAR LEGRemoving of each decayed rear leg from its existing position and replace the same with new rear leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
131	FRONT RAILRemoving of each decayed front rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing .
132	REAR RAILRemoving of each decayed rear rail from its existing position and replace the same with new rear rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing .
133	SIDE RAILRemoving of each decayed side rail from its existing position and replace the same with new side rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing .
134	STIFFNERRemoving of each decayed stiffner from its existing position and replace the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
135	SEATRemoving of decayed/wornout plywood seat from its existing position and replace the same with new seat made out from plywood of 6mm thick, BWR grade, type BB (five Nos of ply) trapezoidal in shape of length 445mm at front side and 405mm at rear side with 440mm in height all as show on drawing
136	POLISHING TO CHAIR WBB W/O ARMRemoval of old existing worn out polish from exposed portion of wooden surface by any means of chair wooden bottom without arm including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
137	RECANNING OF VARIOUS TYPE OF CHAIRS FOR THE FOLLOWING (DRG NO.FD-279, FD-280, FD-281, FD-229) :-Removing of old unserviceable cane plastic from various chairs such as chair dining, chair writing, and chair easy etc re-canning the same with new cane plastic 2mm wide half round white in colour for main canning and 3.5 to 4mm wide half round white in colour for border as approved quality all as shown on drawing.
138	REPAIRS TO ALMIRAH WOODEN MEDIUM WITH SHELVES FOR THE FOLLOWING (DRG NO FD-86M):-
139	BACKRemoving decayed back from its existing postion and replace the same with new back made out from 9mm thick ply wood (five Nos of ply), type BB, BWR grade all as shown on drawing.
140	SIDERemoving decayed each side from its existing position and replace the same with new side made out from 9mm thick ply wood (five Nos of ply), type BB, BWR grade all as shown on drawing.
141	SHUTTERRemoving decayed shutter (Single leaf) from its existing position and replace the same with new leaf made out from 9mm thick ply wood (five Nos of ply), type BB, BWR grade all as shown on drawing.
142	SHELFRemoving each decayed shelf from its existing position and replace the same with new shelf made out from 18mm thick veneered particle board (exterior grade) with commercial face veneers on both sides all as shown on drawing.
143	POLISHING TO ALMIRAH WOODEN MEDIUM WITH SHELVES (DRG NO. FD-86M)Removal of old existing worn out polish from exposed portion of wooden surface by any means of almirah wooden medium with shelves including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
144	REPAIRS TO TABLE WRITING FOR THE FOLLOWING (DRG NO. FD-33, FD-249, FD-275):-
145	LEGRemoving decayed each leg of table writing from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
146	TOP RAILRemoving decayed each top rail of table writing from its existing position and replace the same with new top rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
147	BOTTOM RAILRemoving decayed each bottom rail of table writing from its existing position and replace the same with new bottom rail made out from well 1st class hard wood (Teak/Seasam) all as shown on drawing.
148	STIFFNERRemoving decayed each stiffner of table writing from its existing position and replace the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
149	SIDE BOX WITH DRAWERRemoving decayed side almirah (side box) with drawer and replace the same with 18mm thick veneered particle board (exterior grade) made having teak face at one side and other side commercial for side, back , front and bottom side of the drawer, stiffner, bearer shall be made out from well seasoned second class hardwood, rest all as shown on drawing.
150	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior grade), prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging all as shown on drawing.
151	POLISHING TO TABLE WRITINGRemoval of old existing worn out polish from exposed portion of wooden surface by any means of table writing including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
152	REPAIRS TO TABLE 3’X2’ W/O DRAWER FOR THE FOLLOWING [DRG NO. FD-284, FD-55, FD-42(M)]:-
153	LEGRemoving decayed each leg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
154	TOP RAIL LONGRemoving decayed each top long rail from its existing position and replace the same with new top long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
155	TOP RAIL SHORTRemoving decayed each top short rail from its existing position and replace the same with new top short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
156	STIFFNERRemoving decayed each stiffner from its existing position and replace the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
157	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffner at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.
158	POLISHING TO TABLE 3'x2' W/O DRAWERRemoval of old existing worn out polish from exposed portion of wooden surface by any means of table 3'X2' without drawer including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous making, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
159	REPAIRS TO TABLE 3’X2’ WITH DRAWER FOR THE FOLLOWING [DRG NO. FD-283, FD-41(M) ]:-
160	LEGRemoving decayed each leg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
161	TOP RAIL LONGRemoving decayed each top long rail from its existing position and replace the same with new top long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
162	TOP RAIL SHORTRemoving decayed each top short rail from its existing position and replace the same with new top short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
163	STIFFNERRemoving decayed each stiffner from its existing position and replace the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
164	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffner at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.
165	DRAWERRemoving decayed and replace the drawer made out from well seasoned 1st class hard wood (Teak/Seasam) for front, rear & side with track rail, guide rail & fillet and bottom shall be made out from 6mm thick plywood (five Nos of ply), type BB, BWR grade complete all as shown on drawing.
166	POLISHING TO TABLE 3'x2' WITH DRAWERRemoval of old existing worn out polish from exposed portion of wooden surface by any means of table 3'X2' with drawer including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
167	REPAIRS TO TABLE DINING FOR 6 PERSONS FOR THE FOLLOWING (DRG NO. FD-30, FD-239, FD-273):-
168	LEGRemoving decayed each leg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
169	TOP RAIL LONGRemoving decayed each top long rail from its existing position and replace the same with new top long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
170	TOP RAIL SHORTRemoving decayed each top short rail from its existing position and replace the same with new top short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
171	STIFFNERRemoving decayed each stiffner from its existing position and replace the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
172	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffner at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.
173	HARD RUBBER/PVC TOESRemoving of each decayed hard rubber/toe from its existing position and replace the same with new hard rubber/PVC toe 25mm dia and 25mm high all as shown on drawing and directed by Engr-in-Charge.
174	POLISHING TO TABLE DINING FOR 6 PERSONSRemoval of old existing worn out polish from exposed portion of wooden surface by any means of table dinning of 6 person including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous making, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
175	REPAIRS TO TEAPOY FOR THE FOLLOWING (DRG NO.FD-34, FD-232, FD-382, FD-278):-
176	LEGRemoving decayed each leg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
177	TOP RAIL LONGRemoving decayed each top long rail from its existing position and replace the same with new top long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
178	TOP RAIL SHORTRemoving decayed each top short rail from its existing position and replace the same with new top short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
179	STIFFNERRemoving decayed each stiffner from its existing position and replace the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
180	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffner at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.
181	POLISHING TO TEAPOYRemoval of old existing worn out polish from exposed portion of wooden surface by any means of teapoy including praparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-In-Charge.
182	REPAIRTS TO TABLE CENTRE FOR THE FOLLOWING (DRG NO.FD-29 , FD-235, FD-274 ):-
183	LEGRemoving decayed each leg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
184	TOP RAIL LONGRemoving decayed each top long rail from its existing position and replace the same with new top long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
185	TOP RAIL SHORTRemoving decayed each top short rail from its existing position and replace the same with new top short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
186	STIFFENERRemoving decayed each stiffner from its existing position and replace the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
187	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffner at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.
188	POLISHING TO TABLE CENTRERemoval of old existing worn out polish from exposed portion of wooden surface by any means of table centre including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
189	REPAIRS TO TABLE DRESSING GENTS FOR THE FOLLOWING (DRG NO.FD-230, FD-379):-
190	TOP AND BOTTOM OF BOXRemoving decayed top and bottom of box from its existing position and replace the same with new top made out from 12mm thick pre-laminated particle board (exterior grade), grade-I quality, with 6mm thick well seasoned 1st class hardwood (Teak/Seasom) wooden beading allround the edging. Bottom of the box shall be made out 12mm thick ply wood (seven Nos of ply), type BB, BWR Gde complete all as shown on drawing.
191	SIDE OF BOXRemoving decayed each side of the box from its existing position and replace the same with new side of the box made out from 12mm thick pre-laminated particle board (exterior grade), grade-I quality, one side decorative all as shown on drawing.
192	BACK OF BOXRemoving decayed each back of the box from its existing position and replace the same with new back of the box made out from 12mm thick plywood (seven Nos of ply), type BB, BWR grade all as shown on drawing.
193	DRAWERRemoving decayed drawer and supply and fixing drawer front & side made out from 12mm thick pre-laminated particle board (exterior grade), grade-I quality, one side decorative, bottom shall be made out from 6mm thick ply wood (five Nos of ply), type BB, BWR grade and back shall be made out from 12mm thick well seasoned second class hardwood all as shown on drawing.
194	MIRRORRemoving broken mirror from its existing position and supply and fixing for copper plated 5.5mm thick mirror mounted on new frame made out 6mm thick ply wood (five Nos of ply), type BB, BWR grade with well seasoned Ist Class hard wood all as shown on drawing. Make : Modiguard/Saint gobin as approved.
195	POLHSHING TO TABLE DRESSING GENTSRemoval of old existing worn out polish from exposed portion of wooden surface by any means of table dressing gents including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
196	REPAIRS TO TABLE DRESSING LADIES FOR THE FOLLOWING (DRG NO.FD-251):-
197	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18/19mm thick prelaminated particle board (exterior grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffner as the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.
198	SIDERemoving decayed side from its existing position and replace the same with new side made out from 18mm thick veneered particle board (exterior grade) with one face teak and other face commercial veneer all as shown on drawing.
199	BACKRemoving decayed back from its existing position and replace the same with new back made out from 12 mm thick veneered particle board (exterior grade) with commercial veneers on both faces all as shown on drawing.
200	DRAWERRemoving drawer and replace the side and back of drawer made out from 12mm thick well seasoned 1st class hard wood (Teak/Seasam). Bottom of the drawer shall be made out from 6mm thick ply wood (five Nos of ply), type BB, BWR Gde. Front of the drawer shall be made out from 18mm thick veneered particle board (exterior grade) with commercial veneers on both faces with 1.00mm thick plastic laminated sheet (plain & wood grain) pasted over particle board with approved synthetic adhesive all as shown on drawing.
201	MIRRORRemoving broken mirror with frame and supply and fixing for mirror 5.00 mm thick 355mmx1220mm size free from any cracks/cratches and distorted image etc mounted on 6mm thick ply wood (five Nos of ply), type BB, BWR grade and with 25mmx19mm teak wood well seasoned timber frame all as shown on drawing. Make : Modiguard/Saint gobin as approved.
202	POLISHING TO TABLE DRESSING LADIESRemoval of old existing worn out polish from exposed portion of wooden surface by any means of table dressing ladies including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surfacae is obtained upto the full satisfaction of the Engr-in-Charge.
203	REPAIRS TO TABLE BED SIDE FOR THE FOLLOWING (DRG No FD-276, FD-248, FD-28, FD-210):-
204	TOPRemoving decayed top from its existing position and replace the same with new 18/19mm thick Prelaminated Particle board (exterior grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination including provision of 4mm thick teak wood beading alround the edging all as shown on drawing.
205	LEGRemoving decayed wooden each leg of table bed side from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) of size 65mmx50mm all as shown on drawing.
206	BACKRemoving decayed each back of table bed side from its existing position and replace the same with new back made out from 6mm thick plywood (five Nos of ply), type BB, BWR grade of required size all as shown on drawing.
207	SIDERemoving decayed each side of table bed side from its existing positon and replace the same with 18mm thick one side teak face particle board (exterior grade), grade-I quality of required size all as shown on drawing.
208	POLISHING TO TABLE BED SIDERemoval of old existing worn out polish from exposed portion of wooden surface by any means of table bed side including preparation of new wooden members by sand papering and making the furniture completely smooth fur further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
209	REPAIRS TO TABLE PEG FOR THE FOLLOWING (DRG NO.FD-25, FD-236, FD-277, FD-384):-
210	LEGRemoving decayed each leg of table peg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
211	TOP SHORT RAILRemoving decayed each top short rail from its existing position and replace the same with new short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
212	TOP LONG RAILRemoving decayed each top long rail from its existing position and replace the same with new long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
213	STIFFNERRemoving decayed each stiffner from its existing position and replace the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
214	TOPRemoving decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffner at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.
215	POLISHING TO TABLE PEGRemoval of old existing worn out polish from exposed portion of wooden surface by any means of table peg including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
216	TAKING DOWN OLD UNSERVICEABLE COMPONENTS/ PARTS FROM SOFA SET (5 SEATER/ 4 SEATER/3 SEATER & SINGLE SEATER) AND RE-ASSEMBLE/REFIXING WITH THE FOLLOWING NEW PARTS MADE OUT OF WELL SEASONED TEAK WOOD FREE FROM CRACK, KNOTS, HOLE ETC ALL ASS SPECIFIED AND SHOWN ON DRGS NO. FD-281:-
217	S&F for teak wood arms of sofa sets of required size including taking out unserviceable/damage \\"arms\\" complete all as specified and as shown on drawing.
218	S&F for teak wood legs of sofa sets of required size including taking out unserviceable/damage \\"legs\\"complete all as specified and as shown on drawing.
219	S&F for teak wood bottom of seat & back of sofa sets of required size including taking out unserviceable/damage \\"bottom of seat & back\\" complete all as specified and as shown on drawing.
220	S&F for teak wood front/rear rails of sofa sets of required size including taking out unserviceable/damage \\"front/rear rails\\" complete all as specified and as shown on drawing (Long pieces).
221	S&F for teak wood side rails of sofa sets of required size including taking out unserviceable/damage \\"side rails\\" complete all as specified and as shown on drawing.(3 seater & single seater).
222	POLISHING TO SOFA SET FOUR SEATER (DRG NO. FD-281)Removal of old existing worn out polish from exposed portion of wooden surface by any means of sofa set four seater including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
223	POLISHING TO SOFA SET FIVE SEATER (DRG NO. FD-281)Removal of old existing worn out polish from exposed portion of wooden surface by any means of sofa set five seater including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.
224	REPAIR/REPLACEMENT OF FOAM CUSHION OF CHAIR DINING OFFICER (DRG NO.FD/MAP-II/04):-
225	Removal of old unserviceable foam, cushion of chair dining officers set (comprising of 06 Nos single cushion of seat) and supply and fixing new foam cushion 75mm thick, 450mm x 450mm, 40/32 density, covered with approved quality tapestry cloth (cost of tapestry cloth shall not be less than Rs. 200.00 per metre) and rest all as per Drawing/Directed by Engr-in-charge
226	STIFFNERRemoving decayed each stiffner from its existing position and replace the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
227	POLISHING TO CHAIR DINING OFFICER (DRG NO. FD/MAP-II/04)Removal of old existing worn out polish from exposed portion of wooden surface by any means of chair dinning officer including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-charge.
228	REPAIR/REPLACEMENT OF FOAM CUSHION OF SOFA SET 05 SEATER (DRG NO.FD-281)
229	Removal of old unserviceable foam, cushion sofa set (comprising of 10 Nos single cushion including seat and back) and supply and fixing new foam cushion 100mm thick 40/32 density covered with approved quality tapestry cloth (cost of tapestry cloth shall; not be less than Rs.450.00 per metre). Make : Kurlon/Sleepwell as approved.
230	Removal of old unserviceable tapestry cloth from each foam cushion sofa set (comprising of 10 Nos single cushion) and replace with new tapestry cloth of approveds quality (cost of tapestry cloth shall not be less than Rs. 450.00 per metre).
231	REPAIRS TO CHAIR DINING FOR THE FOLLOWING (DRG NO : FD-MAP-II/05)
232	FRONT LEGRemoving of each decayed front leg from its existing position and replace the same with new front leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.
233	REAR LEGRemoving each decayed rear leg from its existing position and replace the same with new rear leg made out from well seasoned 1st class hard wood (Teak / Seasam) al as shown drawing.
234	FRONT RAILRemoving of each decayed front rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak / Seasam) all as shown on drawing.
235	REAR RAILRemoving of each decayed rear rail from its existing position and replace the same with new rear rail made out from well seasoned 1st class hard wood (Teak / Seasam) all as shown on drawing.
236	SIDE RAILRemoving of each decayed side rail from its existing position and replace the same with new side rail made out from well seasoned 1st class hard wood (Teak/ Seasam) all as shown on drawing
237	REAR STIFFENERRemoving of each decayed rear stiffener from its existing position and replace the same with new rear stiffener made out from well seasoned 1st class hard wood (Teak / Seasam) all as shown on drawing.
238	STIFFENERRemoving of each decayed stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak / Seasam) all as shown on drawing.
239	HARD RUBBER / PVC RINGRemoving of each decayed hard rubber / PVC ring from its existing position of Chair dinning and replace the sme with new hard rubber / PVC ring all as shown on drawing and directed by Engineer-in-Charge.
240	SEATRemoving of decayed / wornout PVC seat from its existing position and replace the same with new seat of size 4mm x 10mm thick ribs molded long with single frame all as show on drawing and directed by Engineer-in-Charge.(Make:Brite/Cello/Supreme/Nilkamal as approved)
241	POLISHING TO CHAIR DININGRemoval of old existing worn out polish from exposed portion of wooden surface by any meand of chair dining including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engineer-in-Charge. Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Tamil Nadu Tenders

Services Tenders

Painting Work Tenders

Painting Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Repair / Painting Of Steel Furniture And Repair / Polishing Of Wooden Furniture At Bso Avadi Under Ge Avadi, Avadi-Tamil Nadu

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Repair / Painting Of Steel Furniture And Repair / Polishing Of Wooden Furniture At Bso Avadi Under Ge Avadi, Avadi-Tamil Nadu

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us