Tender For special Repair To 06 X Or Govt Md Accn Bldg No. P-204/01 To 204/06 At Lancer Line-Ii And Bldg No. P-207 (06 X Or Md Accn) At Lancer Line-Ii Of Mil Hospital And Bldg No. P-15, P-16, P-17 & P-18 At Bso Yard At Army Area Jodhpur Under Ge (Arm
Tender Value
1.31 Crore
Estimated cost
Bid Submission
11 Jul 2026
2 days left
EMD
2.06 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To 06 X Or Govt Md Accn Bldg No. P-204/01 To 204/06 At Lancer Line-Ii And Bldg No. P-207 (06 X Or Md Accn) At Lancer Line-Ii Of Mil Hospital And Bldg No. P-15, P-16, P-17 & P-18 At Bso Yard At Army Area Jodhpur Under Ge (Army) No. 01
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in-charges. |
| 2 | Dismantling of Stone slabs in roofs, suspended floors, chajjas, landings,floor/wall tiles etc., any thickness, jointed in any mortar. complete all as specified and directed by Engr-in-charges. |
| 3 | M&L for cutting in to old masonry built in cement mortar to form toothings for bonding in new brick or stone work including making good in cement mortar 1:6 complete all as specified and directed by Engr-in-charges. |
| 4 | M&L for squarred rubble walling Jodhpur type regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed by Engr-in-charges. |
| 5 | All as per item No 4 above but except stone complete all as specified and directed by Engr-in-charges. |
| 6 | M&L Precast cement concrete solid building blocks 10 cm thick type B1 1:2:4 set in cement mortar (1:6) in walls complete all as specified and directed by Engr-in-charges. |
| 7 | Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing complete to squared rubble walling, regular coursed, Jodhpur type complete all as specified and directed by Engr-in-charges. |
| 8 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engr-in-charges. |
| 9 | M&L for 25mm thick cement concrete type B-0 1:2:4 as in subbase of floor tiles (using 12.5 mm graded crushed stone aggregate) complete all as specified and directed by Engr-in-charges. |
| 10 | M&L for 15 mm thick screed bed or bedding layer in CM 1:6 floor finished even & rough to receive tiling/floor finishes complete all as specified and directed by Engr-in-charges. |
| 11 | M&L for Non-skid coloured ceremic tiles joint less 7 to 8 mm thick area of each tiles exceeding 0.18 Sqm but n.exc.0.38 sqm in floor etc set jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and directed by Engr-in-charges. |
| 12 | All as per above item No. 11 but skirting including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engr-in-charges. |
| 13 | M&L Non skid ceramic colour joint free tiles 6 to 7 mm thick of size area exc 0.11 Sqm but nexc 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-charges. |
| 14 | M&L for glazed colour ceramic tiles of size 300x450x7mm thick, laid in vertical surface dado/skirting joint free etc, set and jointed in neat cement slurry and pointed in coloured tiles to match the shade of tiles (High-lighter pattern) complete all as specified and directed by Engr-in-charges. |
| 15 | M&L for 10mm thick rendering in CM 1:4 over stone masonary surfaces finished even & rough to receive tiling etc finish complete all as specified and directed by Engr-in-charges. |
| 16 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed by Engr-in-charges. |
| 17 | M & L 18 to 20 mm thick machine cut Kota stone slab flooring over screed bed base ,laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing icluding 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed by Engr-in-charges. |
| 18 | M & L 18 to 20 mm thick machine cut Kota stone in riser of steps, skirting, dado and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing including 10 mm thick rendering in cement mortor 1:6 complete all as specified and directed by Engr-in-charges. |
| 19 | M & L 18 to 20 mm thick machine cut Kota stone in shelves and other places etc laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing complete all as specified and directed by Engr-in-charges. |
| 20 | M & L 18 to 20 mm thick machine cut one side polished black granite in kitchen plate form and windows cill, set and jointed including 20 mm thick screed bed in cement mortar 1:3, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing complete all as specified and directed by Engr-in-charges. |
| 21 | Taking down existing cement plaster including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-charges. |
| 22 | M&L for 15 mm thick rendering CM (1:4) over stone masonary surfaces finished even & smooth without extra cement complete all as specified and directed by Engr-in-charges. |
| 23 | M&L Rendering 10 mm thick CM (1:3) on concrete surfaces on ceiling / facia of RCC roof projection at any height etc all as directed & finished even & smooth without using extra cement complete all as specified and directed by Engr-in-charges. |
| 24 | M&L for 20 mm thick rendering in CM 1:6 finished even and smooth without extra cement on stone wall surface in two layes complete all as specified and directed by Engr-in-charges. |
| 25 | Racking out joints/pointing to square rubble masonry Jodhpur type regular coursed built in cement mortar complete all as specified and directed by Engr-in-charges. |
| 26 | M&L for Keyed pointing to square rubble masonry Jodhpur type regular course in CM 1:3 complete all as specified and directed by Engr-in-charges. |
| 27 | M&L preperartion of newly plastered surfaces on wall and applying 1.5 -2 mm thick wall care putty with fair finished and even surface and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed by Engr-in-charges. |
| 28 | M&L for complete removal of existing distempered surfaces of walls and applying two coats of oil emulsion distemper of white shade or other approved shade over two coat of birla white putty on plastered surface complete all as specified and directed by Engr-in-charges. |
| 29 | M&L for applying three coats of white wash on newly plastered surface of wall including preparation of surfaces complete all as specified and directed by Engr-in-charges. |
| 30 | M&L for applying three coats of white wash on newly plastered surface of ceiling including preparation of surfaces complete all as specified and directed by Engr-in-charges. |
| 31 | M&L for applying one coats of white wash on old surface of wall complete all as specified and directed by Engr-in-charges. |
| 32 | M&L for applying one coats of white wash on old surface of ceiling complete all as specified and directed by Engr-in-charges. |
| 33 | M&L for applying two coats of cement based paint on newly plastered/ unplastered surface of wall including preparation and one coat of chalk white of surfaces complete all as specified and directed by Engr-in-charges. |
| 34 | M&L for applying two coats of cement base paint on old surfaces including preparation of existing wall surfaces complete all as specified and directed by Engr-in-charges. |
| 35 | M&L for applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed by Engr-in-charges. |
| 36 | M&L for applying two coats of synthetic enamel paint on New or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of surfaces complete all as specified and directed by Engr-in-charges. |
| 37 | Taking down chowkhats or frames with shutter not exc 1.5 sqm each (without taking off shutter from the frame)complete all as specified and directed by Engr-in-charges. |
| 38 | Taking down chowkhats or frame with shutter exc 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutter from the frame) complete all as specified and directed by Engr-in-charges. |
| 39 | Taking down shutter of any description, exc.1 Sqm but n exc 2 Sqm each complete all as specified and directed by Engr-in-charges. |
| 40 | M & L for Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors and frame ; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engr-in-charges. |
| 41 | M & L for mild steel framed work as in brackets etc for cooler stands etc framed steps/stairs etc complete using MS angle iron Steel bars gusset plate etc confirming to Fe290,Gde-E-165 complete all as specified and directed by Engr-in-charges. |
| 42 | Taking out from position framed woodwork as in cupboards/cabinets etc with all fittings ,shutters, shelves, drawers etc in any position fixed in walls or floors & removal of the rubbish outside MD land all as directed at site for overall sizes exc 0.50 sqm but nexc 1.50 sqm & depth nexc 60 cm complete all as specified and directed by Engr-in-charges. |
| 43 | M&L for UPVC Caoted Celuka printed in one of two different colours( with wood grain printed pattern /ivory clour finish) polyvinyl chloride (PVC) sheet frame of width exc. 100mm & 18mm thickness made out of extruded 18mm PVC sheet and joined with suitable Cement Solvent adhesive and screw.The frame shall be fixed to the wall using 75mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 3 Nos. of screws to be provided for each vertical member & minimum 2 Nos. for horizontal member etc all as per manufracturers specifications, complete all as specified and directed by Engr-in-charges. |
| 44 | M&L for 18 mm thick solid PVC sheet UPVC Caoted Celuka printed in one of two different colours( with wood grain printed pattern /ivory clour finish) as in kitchen cabinet shutters ,all round body of cabinets , shelves ,drawers etc cut to required size jointed with solvent cement including including PVC boards for lipping 1-1.5 mm thick 18 mm wide & steel screws etc complete all as specified & directed . |
| 45 | M&L for stainless steel tray as per trade pattern of various sizes for drawer to keep the kitchen utensil complete all as specified and directed by Engr-in-charges. |
| 46 | S&F drawer runners folding type stainless steel with guide channels & sliding channel with approipiate ball bearing/ rollers etc complete to obtain smooth movement of the drawers. complete all as specified and directed by Engr-in-charges. |
| 47 | S&F 0 degree clip type self closing hinges for cabinets fixed with cadimum coated screws complete all as specified and directed by Engr-in-charges. |
| 48 | S&F 75mm size bright finished cromium plated steel handle of approved shape & design fixed with cadmium coated screws on the kitchen cabint drawers complete all as specified and directed by Engr-in-charges. |
| 49 | S&F Magnetic catches for cabinets of size 50 mm complete with striking plate & magnetic stud complete all as specified and directed by Engr-in-charges. |
| 50 | S&F for (a) of 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 complete all as specified and directed by Engr-in-charges. (a); supplied and fitted to chowkats with followings:-(b) SS wire cloth 0.36mm nominal dia of wire, average width of aperture 1.40mm fixed with SS wire staple.(c) Aluminium Grill Medium grade mess size 50x50mm , fixed at outer edge at outer edge of door.(d) Apply one coat of Pink-Primer |
| 51 | S&F for Flush shutters 35 mm thick, solid core construction core with block board and plywood face panels, commercial type on both side. One face covered with decorative face veneer with lipping / frame edging to match and other face shall be covered with prelaminated sunmica with mortic lock and handle complete all as specified and directed by Engr-in-charges. |
| 52 | S&F for (a) of 2nd class hardwood 35mm thick Partialy gauzed and Panelled shutters, open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 complete all as specified and directed by Engr-in-charges. (a); supplied and fitted to chowkats with followings:-(b) SS wire cloth 0.36mm nominal dia of wire, average width of aperture 1.40mm fixed with SS wire staple.(c) Aluminium Grill Medium grade mess size 50x50mm , fixed at outer edge at outer edge of door.(d) Apply one coat of Pink-Primer |
| 53 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed by Engr-in-charges. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 54 | Providing & Fixinng Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engr-in-charges. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 55 | Taking down steel window/ ventilator complete all as specified and directed by Engr-in-charges. |
| 56 | S&F Factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed by Engr-in-charges. (with or without cooler opening as directed by engr-in-charge) |
| 57 | S&F Factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed by Engr-in-charges.(with or without cooler opening as directed by engr-in-charge) |
| 58 | S&F Factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed by Engr-in-charges. |
| 59 | S&F Factory made box type steel ventilator without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed by Engr-in-charges. |
| 60 | S&F of aluminium anodized barrel tower bolt 200 mm long Extrudid section complete all as specified and directed by Engr-in-charges. |
| 61 | S&F aluminum anodised handle extruded section of size 150mm long fabricated type complete all as specified and directed by Engr-in-charges. |
| 62 | S&F for aluminium alloy anodised sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 300mm long complete all as specified and directed by Engr-in-charges. |
| 63 | S&F of stainless steel butt hinges 100 mm size medium weight complete all as specified and directed by Engr-in-charges. |
| 64 | S&F of mild steel butt hinges 100 mm size medium weight, cold rolled complete all as specified and directed by Engr-in-charges. |
| 65 | S&F 100mm size Mild steel single action door spring hinge complete all as specified and directed by Engr-in-charges. |
| 66 | S&F floor door stopper of alluminium alloy body and toungue anodised with hard drawn steel spring 140mm long complete all as specified and directed by Engr-in-charges. |
| 67 | S&F of 4 mm thick pinheaded Figured glass & glazing with oil putty in squares of size not. exceeding 0.5 Sqm in each pane fixed with oil putty complete all as specified and directed by Engr-in-charges. |
| 68 | S&F for 3 mm thick plain sheet glass ordinary quality & glazing with oil putty in squares n exc 0.5 Sqm in each pane complete all as specified and directed by Engr-in-charges. |
| 69 | S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.00 mm complete all as specified and directed by Engr-in-charges. |
| 70 | S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.00 mm with necessary fitting on steel/ wooden surface complete all as specified and directed by Engr-in-charges. |
| 71 | M&L for PCC 1:2:4 type B1 Mix using 20mm graded stone aggregate as in hold fast iron fixing,coping, chamfered edges including necessary form work complete all as specified and directed by Engr-in-charges. |
| 72 | S&F Mild steel flat iron for hold fast and similar work confirming to Fe-290 Gde-E-165 fixed with welding and necessary item complete all as specified and directed by Engr-in-charges. |
| 73 | S&F Stainless steel 25mm curtain rod with fixing brackets, knob etc as in repairs complete all as specified and directed by Engr-in-charges. |
| 74 | S&F in repair shelf of PTMT fixed with and including chromium plated brass screws and wooden cleats (Min weight 300 gms) complete all as specified and directed by Engr-in-charges. |
| 75 | S&F in repair brass Chromium plated 100 mm size soap dish fixed with screws & pluges complete all as specified and directed by Engr-in-charges. |
| 76 | S&F in repair brass chromium plated tubular towel, D type rail 600mm long 20mm dia fixed to wall with chromium plated brass screws and pvc cleats of approved make complete all as specified and directed by Engr-in-charges. |
| 77 | S&F 600x450mm and 5 bevelled edge mirror of selected quality glass mounted on PVC frame fixed to wooden plugs with chromium plated brass screws and cup washres complete all as specified and directed by Engr-in-charges. |
| 78 | S&F in repair sheet glass corner shelf assembly consisting of 5.5mm thick sheet glass shelf 300m base/wide with aluminium alloy brackets and gaurd and railing 60cm long complete all as specified and directed by Engr-in-charges. |
| 79 | S&F in repair MS chromium plated peg set of five fixing with wall complete all as specified and directed by Engr-in-charges. |
| 80 | S&F in repair sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or fixing in RCC slab and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engr-in-charges. |
| 81 | S&F Stainless steel Plate Racks made of stainless steel 1.00 mm thick with plugs, washers and fixed with bolts /screws of size 750 X 600 X 250 mm as in repair complete all as specified and directed by Engr-in-charges. |
| 82 | S & F as in repairs vitreous china wash down water closet Anglo Indian Type (Semi pedestal pattern) with seat & cover complete incl fixing of flush pipe etc complete all as specified and directed by Engr-in-charges. |
| 83 | S & F in repair Vitrous china wash basin, white flat size 450x300 mm including , waste pipe, MS brackets complete all as specified and directed by Engr-in-charges. |
| 84 | Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 110mm bore complete all as specified and directed by Engr-in-charges. |
| 85 | Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 75mm bore complete all as specified and directed by Engr-in-charges. |
| 86 | S&F 110 mm dia PVC pipe (SWR) single socketed in any length with rubber ring joint, laid in trenches or in floor or in floor complete all as specified and directed by Engr-in-charges. |
| 87 | S&F 75 mm dia PVC pipe (SWR) single socketed in any length with rubber ring joint, laid in trenches or in floor or in floor complete all as specified and directed by Engr-in-charges. |
| 88 | S&F 110 mm dia PVC pipe (SWR) single socketed in any length with rubber ring joints fixed on wall complete all as specified and directed by Engr-in-charges. |
| 89 | S&F 75 mm dia PVC pipe (SWR) single socketed in any length with rubber ring joints fixed on wall complete all as specified and directed by Engr-in-charges. |
| 90 | S&F in repairs stack clamp out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75/100mm dia pipe. complete all as specified and directed by Engr-in-charges. |
| 91 | M&L WC connector 110 mm PVC SWR with lip zing for WC complete all as specified and directed by Engr-in-charges. |
| 92 | S&F 110mm dia PVC (SWR) Junction Single 'T' equal or unequal complete all as specified and directed by Engr-in-charges. |
| 93 | S&F 110mm dia PVC reducer (SWR) complete all as specified and directed by Engr-in-charges. |
| 94 | S&F 110mm dia PVC (SWR) bends any radius with access door of radius complete all as specified and directed by Engr-in-charges. |
| 95 | S&F 75mm dia PVC (SWR) bends any radius with access door of radius complete all as specified and directed by Engr-in-charges. |
| 96 | M&L PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm dia of outlet. complete all as specified and directed by Engr-in-charges. |
| 97 | S&F 100 mm dia PVC (SWR) vent cowl fixed to pipe complete all as specified and directed by Engr-in-charges. |
| 98 | S&F in repair of brass chromium plated shower rose 150mm dia round/square shape with shower arm complete all as specified and directed by Engr-in-charges. |
| 99 | S &F in repair 25 mm dia stop valves, cast copper alloy with screw down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union & fixed of 25mm dia complete all as specified and directed by Engr-in-charges. |
| 100 | S & F as in repairs 15 mm dia angular stop cock cast copper alloy with chromium plated long thread with flange complete all as specified and directed by Engr-in-charges. |
| 101 | S & F as in repairs 15 mm dia two way angular stop cock cast copper alloy with chromium plated long thread with flange complete all as specified and directed by Engr-in-charges. |
| 102 | S & F in repair Bidet spray (Health faucet) with 1 meter PVC tube and holder, complete all as specified and directed by Engr-in-charges. |
| 103 | S& F as in repairs chromium plated Wall mixer 3-in-1 system including 1.50mtr long Tele shower of size 50mm dia with adujstable wall flange complete all as specified and directed by Engr-in-charges. |
| 104 | S&F as in repairs of 15 mm dia bib cock long body with flange with chromium plated cast copper alloy fixed with iron pipe complete all as specified and directed by Engr-in-charges. |
| 105 | S&F as in repairs 15mm bore CP central hole basin mixer popup waste system with 450mm long copper pipe and brass nuts fixed with iron pipe complete all as specified and directed by Engr-in-charges. |
| 106 | Supply & Fixing low level flushing cistern PVC valveless, Syphonic action type 10 ltrs capacity with float valves (ISI Marked) white with inlet ball valve including float and includign pvc connection complete all as specified and directed by Engr-in-charges. |
| 107 | Dismantling water tanks of capacity exc 250 ltrs but.nexc 500 ltrs and removing to store complete all as specified and directed by Engr-in-charges. |
| 108 | S&F in replacement rotational moulded polythene water storage tanks (cylindrical vertical with closed top hoisted and fixed in position all as specified in SSR Part -I capacity of tank 500 ltrs including tank led cover complete with fixing arrangement complete all as specified and directed by Engr-in-charges. |
| 109 | S&F in repair 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed by Engr-in-charges. |
| 110 | M&L for 100 thick PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in water tank plateform over roof top finished even and smooth complete all as specified and directed by Engr-in-charges. |
| 111 | Demolition of reinforced cement concrete (reinforcement cut as required to faciliate demolition) as in beams, in roofs, floor (other than ground floors) staircase, landing, chajjas and similar suspended work of any description and any position not otherwise complete all as specified and directed by Engr-in-charges. |
| 112 | M&L for Providing precast RCC type B1 1:2:4 (using 20mm graded aggregate) as in cover slab for man holes set in CM 1:6 complete all as specified and directed by Engr-in-charges. |
| 113 | M&L 50mm thick sand stone slabs in sunshades, chajjas, shelves, cills, landings cover slabs on manholes stones templates etc n exc 2m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in cement mortar 1:4 thickness complete all as specified and directed by Engr-in-charges. |
| 114 | Supply only Integral water proofing compund complete all as specified and directed by Engr-in-charges. |
| 115 | Taking down or up steel tubing and connection including cleaning for refixing or removal to store complete all as specified and directed by Engr-in-charges. |
| 116 | (a) 25 mm dia |
| 117 | (b) 20 mm dia |
| 118 | (c ) 15 mm dia |
| 119 | Supplying and laying of CPVC pipes, SDR 11 & Plain CPVC SDR 11 including all brass fittings, laid in trenches or ceiling or fixed to wall including cutting chases, pinning in & making good to disturbed portion complete all as specified and directed by Engr-in-charges. |
| 120 | (a) 25 mm dia, |
| 121 | (b) 20 mm dia |
| 122 | (c) 16 mm dia including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc complete. |
| 123 | Demolition of reinforced cement concrete of any description and in any position complete (reinforcement cut as required to faciliate demolition) complete all as specified and directed by Engr-in-charges. |
| 124 | M&L RCC design mix M-25 using 20 mm graded stone aggregate as in slab supported on wall, roof slab, chijja and in shelve etc complete all as specified and directed by Engr-in-charges. |
| 125 | M&L RCC design Mix-25 using 20 mm graded stone aggregate as in beam, roof beam, cantilevers, lintel beam, etc. complete all as specified and directed by Engr-in-charges. |
| 126 | S&F mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed by Engr-in-charges. |
| 127 | S&F mild steel TMT bar 6 to 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed by Engr-in-charges. |
| 128 | S&F mild steel TMT bar 5 dia and over upto and including 10 mm dia as in stirrups cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed by Engr-in-charges. |
| 129 | Use and waste of formwork to sides and soffits of slabs n. exc. 200 mm thick and similar works fair finished surfaces of concrete complete all as specified and directed by Engr-in-charges. |
| 130 | Use and waste of From work to edge of concrete flats, treads, breaks in floors, window cills, concrete railing, opening in concrete walls, floor and roofs n exc 20 cm wide and side of RCC/PCC bands in walls horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide with fair finished surfaces complete all as specified and directed by Engr-in-charges. |
| 131 | Use and waste of form work to sides and soffits of floor or roof beams, lintel, cantilevers, shelves etc. including support of fair finished surfaces complete all as specified and directed by Engr-in-charges. |
| 132 | M& L for roof treatment in the following stages :- (a) first Course : M&L for 15 mm thick plaster with CM 1:3 mixed surface even and smooth with water proofing compound as per manufacturee instructions (Note: - WPC shall be measured and paid separately).(b) Material and labour for UV stable single component fibre reinforced elastomeric liquid applied water proofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/10 sqft in two coats (10-12 hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must. complete all as specified and directed by Engr-in-charges. Note : - 1.The authorized applicator of manufacturer shall be approved by GE. |
| 133 | Demolition of cement concrete in ground floors and pavings n. exe 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-charges. |
| 134 | M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete etc complete all as specified and directed by Engr-in-charges. |
| 135 | M&L 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar places, without using extra cement including cutting of joints n.exc 3.0 mtr length complete all as specified and directed by Engr-in-charges. |
| 136 | M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed by Engr-in-charges. |
| 137 | M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed by Engr-in-charges. |
| 138 | M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including wateringas required complete all as specified and directed by Engr-in-charges. |
| 139 | Material & labour for hardcore of broken stone of gauges n.exc. 63mm, deposited spread and leveled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed by Engr-in-charges. |
| 140 | M&L for precast RCC 1:2:4 Type B 1 using 20mm graded stone aggregate as in manhole/drain cover with hole/without hole hoisted & laying in position complete all as specified and directed by Engr-in-charges. |
| 141 | M&L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate for 150 mm dia pipe complete all as specified and directed by Engr-in-charges. |
| 142 | Supply & laying jointing and testing 150mm bore reinforced concrete pipes class NP-2 laid and jointed in cement mortor 1:1 complete with collars or socket/spigot type laid jointed and haunching at side in cement complete all as specified and directed by Engr-in-charges. |
| 143 | M&L for Cutting into existing manholes for connecting 150 mm new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required. complete all as specified and directed by Engr-in-charges. |
| 144 | M&L for 100mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in flooring,path , sub base etc complete all as specified and directed by Engr-in-charges. |
| 145 | M&L for laying 50 mm thick Machine cut sand stone slabs as in Plinth protections laid over and including 20 mm thick cement sand screed in CM1:4 over 50 mm thick PCC 1:4:8 D2 all as specified and directed incl filling the joints of sand stone slabs with neat cement mixed with pigment to match the shade of slabs complete all as specified and directed by Engr-in-charges. |
| 146 | M&L Virtrified Ceramic tiles Light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including M&L 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed by Engr-in-charges. |
| 147 | M&L for 15mm thick rendering in CM 1:6 finished even and smooth without extra cement on stone wall surface complete all as specified and directed by Engr-in-charges. |
| 148 | M&L for 15mm thick rendering in CM 1:4 finished fair and even without using extra cement with WPC compound on stone wall surface complete all as specified and directed by Engr-in-charges. Note: WPC shall be measured and paid seperately. |
| 149 | M&L for 5mm thick rendering in CM 1:3 finished even and smooth without extra cement on Ceilings complete all as specified and directed by Engr-in-charges. |
| 150 | S&F mild steel frame work as in stairs ,hand rails/ladder half round or other stock section or section or core for wooden hand rail straidgt portion drilled and countershunk for balusters running bars for doors balusters nosing to steps including embedded in concrete and screwing etc wind ties for foof including securing bolts post and struts in fencing including securing bolts post and struts in fencing including cutting tops to shape as directed drilling holes nothing for wire etc flat iron fillet for necessary drilling boltinh or riveting etc and similar work confirming to Fe 410-0 or fe 310-0 complete all as specified and directed by Engr-in-charges. |
| 151 | M&L as in repairs for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape incl two coats of synthetic enamel paint on interior surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete all as specified and directed by Engr-in-charges. |
| 152 | S&F of pressed steel frames of size 125x60mm for doors with one or more rebates incl necessary fixing lugs,hinges,lock strice plate etc complete all as specified and directed by Engr-in-charges. |
| 153 | M&L PCC (1:2:4) type B-0 using 12.5 mm aggregate in filling pressed steel frame, concrete shall be compressed complete all as specified and directed by Engr-in-charges. |
| 154 | M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening complete all as specified and directed by Engr-in-charges. |
| 155 | M&L Factory made solid panel of PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site complete all as specified and directed by Engr-in-charges. |
| 156 | S&F MS with PVC coated decorative 25mm curtain rod with fixing brackets, knob etc as in repairs complete all as specified and directed by Engr-in-charges. |
| 157 | S&F in repair soap dish of PTMT fixed with screws complete all as specified and directed by Engr-in-charges. |
| 158 | S&F in repair PTMT towel rail 450mm long fixed to wall with chromium plated brass screws and wooden cleats Min weight 170gms approved make complete all as specified and directed by Engr-in-charges. |
| 159 | S&F as in repairs of vitreous china clay water closet squatting pan ORISSA Pattern size 580x 440 mm white with integral foot rest incl 'P' or 'S' traps, flush pipe of 32mm dia HDPE pipe etc complete all as specified and directed by Engr-in-charges. |
| 160 | S&F 100 mm dia Cast iron (sand cast) soil waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed by Engr-in-charges. |
| 161 | S&F 75 mm dia Cast iron (sand cast) soil waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed by Engr-in-charges. |
| 162 | S&F100 mm CI branch pieces single socketed Y (equal or unequal) ordinary or inverted (spigot or socketed type) or with parallel brass chy complete all as specified and directed by Engr-in-charges. |
| 163 | S&F75 mm CI branch pieces single socketed Y equal or unequal ordinary or inverted (spigot or socketed type) or with parallel brass chycomplete all as specified and directed by Engr-in-charges. |
| 164 | S&F100mm CI bends any radius complete all as specified and directed by Engr-in-charges. |
| 165 | S&F 75 mm dia CI bend with oval acess door fixed to pipe complete all as specified and directed by Engr-in-charges. |
| 166 | S&F 100mm dia CI vent cowl fixed to pipe complete all as specified and directed by Engr-in-charges. |
| 167 | S&F 75 mm dia CI floor trap plain with grating including jointing with solvent cement 75mm dia complete all as specified and directed by Engr-in-charges. |
| 168 | S&F in repair chromium plated 15mm dia pillar cock long neck with aerator complete all as specified and directed by Engr-in-charges. |
| 169 | S& F as in repairs 15 mm dia stop cock regular body with adujstable wall flange with chromium plated with (concealed type) complete all as specified and directed by Engr-in-charges. |
| 170 | M&L for Providing and fixing polyvinyl chloride (PVC) sheet frame of width 150 mm & 18 mm thickness made out of extruded 18mm PVC sheet and joined with suitable Cement Solvent adhesive and screw.The frame shall be fixed to the wall using 75mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 3nos. of screws to be provided for each vertical member & minimum 2nos. for horizontal member etc. complete all as specified and directed by Engr-in-charges. |
| 171 | S & F Auto hinges, stainless steel, complete assembly complete all as specified and directed by Engr-in-charges. |
| 172 | Extra over PVC boards for lipping 1-1.5 mm thick 18 mm wide complete all as specified and directed by Engr-in-charges. |
| 173 | S&F 100mm size bright finished chromium plated steel handle of approved shape & design fixed with cadmium coated screws on the kitchen cabint shutters complete all as specified and directed by Engr-in-charges. |
| 174 | M&L 50 thick PCC (1:2:4)Type B-1 using 20 mm graded stone aggregate for water tank plinth complete all as specified and directed by Engr-in-charges. |
| 175 | Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed by Engr-in-charges. |
| 176 | (a) 25 mm dia |
| 177 | (b) 20 mm dia |
| 178 | (c ) 15 mm dia |
| 179 | S&F of water tubing, medium grade, galvanized, with all fittings fixed to wall complete all as specified and directed by Engr-in-charges. |
| 180 | (a) 25 mm dia, |
| 181 | (b) 20 mm dia |
| 182 | (c ) 15 mm dia including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc complete. |
| 183 | M&L for 10mm thick rendering in CM 1:6 finished even and smooth without using extra cement on cocrete surfaces of roof with WPC compound complete all as specified and directed by Engr-in-charges. Note:- WPC shall be measured and paid seperately. |
| 184 | Material and labour for UV stable single component fibre reinforced elastomeric liquid applied waterproofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/10 sqft in two coats (10-12 hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must. complete all as specified and directed by Engr-in-charges. Note : - The work shall be executed by the authorized applicator of the manufacturer only. Note : - 1.The authorized applicator of manufacturer shall be approved by GE. 2.The color of final finish shall be decided by the GE |
| 185 | S&F 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face covered with decorative face veneer with lipping/frame to match, complete all as specified & directed by Engineer-in-charge. |
| 186 | Material & labour for PCC (1:4:8) type D-2, 75 mm thick (using 40 mm graded stone agg) as in sub base of floor surface complete all as specified and directed by Engr-in-charges. |
| 187 | M&L for machine cut pre-polished kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 20mm thick screed bed or bedding layer in CM 1:4 complete all as specified and directed by Engr-in-charges. |
| 188 | M&L for glazed colour ceramic tiles of size 450x300x7mm, laid in vertical surface dado/skirting joint free etc, set and jointed in neat cement slurry and pointed in coloured tiles to match the shade of tiles over 10 mm thick rendering in CM1:3 over stone masonry surfaces & finished even & rough to receive tiles. complete all as specified and directed by Engr-in-charges. |
| 189 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & directed by Engineer-in-charge. |
| 190 | M&L for Preparing of new surface plastered or unplastered surfaces andapplying two coats of oil bound distemper over and including M&L for one coat of primer on walls complete all as specified and directed by Engr-in-charges. |
| 191 | M&L for preparing surfaces plastered or unplasterd on new surfaces with 2 coats of Oil Bound distemper on Ceilings complete all as specified and directed by Engr-in-charges. |
| 192 | Excavating in post holes each n exc 0.5 cum , getting out in Hard/dense soil ,returning filling in and ramming earth or broken rubble mixed with earth around, in layers nt exc 25cm ,watering and removing surplus soil to a distance n exc 50m and making good surface complete all as specified and directed by Engr-in-charges. |
| 193 | M&L for cement concrete in foundations ,filling and mass concrete type C2 1:3:6(40 mm gradede aggregrate) as in post hole and complete all as specified and directed by Engr-in-charges. |
| 194 | M&L for rolled mild steel roof trusses(framed), trussed,vertical post,purlins,crane gantries,rails and fastenings and heavy bracket framing including distance pieces, cleats,tee,angle etc. confirming to Fe410-W (Gde E-250)Quality A as in curved shape, complete all as specified and directed by Engr-in-charges. |
| 195 | M&L for Rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe410-W (Gde E-250)Quality A, complete all as specified and directed by Engr-in-charges. |
| 196 | Dismantling of Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings all of any thickness and guage complete all as specified and directed by Engr-in-charges. |
| 197 | S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet (mangolare pattern) 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering to wall fixed with self tapping screws as specified complete all as specified and directed by Engr-in-charges. |
| 198 | M&L Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and Fixing confirming to Fe410-W (Gde E-250)Quality A, complete all as specified and directed by Engr-in-charges. |
| 199 | Demolition of cement concrete (unreinforced) of any description and any position not otherwise specifically provided for (roof padding) including dismantling of existing roof membrane and cement mortar and removal of debris outside of MOD land complete all as specified and directed by Engr-in-charges. |
| 200 | M&L for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof padding over old cleaned surface of any description on roof/terrace to fill any depressions etc or to obtain desired slopes. complete all as specified and directed by Engr-in-charges. |
| 201 | M&L Rendering 20mm thick in cement mortar (1:4), mixed with integral water proofing liquid all as per manufacturer's instructions over concrete roof surfaces finished even and smooth with out using extra cement complete all as specified and directed by Engr-in-charges. |
| 202 | M&L for carrying out water proofing treatment for roofs in the following stages - (ii) Material and labour for UV stable single component fibre reinforced elastomeric liquid applied waterproofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat with laying of geo-fibre mesh at ratio of damp proof ultra water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/10 sqft in two coats (10-12 hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must. Note : - The work shall be executed by the authorized applicator of the manufacturer only. complete all as specified and directed by Engr-in-charges. Note : - 1.The authorized applicator of manufacturer shall be approved by GE. 2.The color of final finish shall be decided by the GE |
| 203 | M&L for post construction anti termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed by Engr-in-charges. |
| 204 | M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed by Engr-in-charges. |
| 205 | M&L for PCC 1:3:6 (Type C-1 , 20mm graded aggregate) as in surface channels and drains complete all as specified and directed by Engr-in-charges. |
| 206 | Taking down carefully copper/aluminium point wiring for light, fan, bell socket power slocket etc complete with boards, outlet boxes fittings and fixtures such as switchs, sockets, lamp holders bracket, ceiling rose etc complete all as specified and directed by Engr-in-charges. |
| 207 | Taking down carefully sub-main wiring (with DB any type) of any size and making good to ther disturbed surfaces to match the existing complete all as specified and directed by Engr-in-charges. |
| 208 | Taking Down carefully DB any of any Size and making good to their disturbed surface to match the exixting complete all as specified and directed by Engr-in-charges. |
| 209 | M&L for point wiring complete with 1.5 Sq mm single core PVC insulated but unshealthed multistranded copper conductor FRLS cable 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed (where their is no cutting chesses in ceiling) in wall or ceiling etc including 1.5 Sq mm, single core, PVC insulated but unsheathed multi stranded copper conductor FRLS cables 1100 Volts, green colour grade as earth continuity wire including sunken type presses steel terminal boxes of suitable size with brand name mentioned on box with 3mm thick bakelite sheet white/coloured top cover and must be colourcode for wiring as red, yellow, blue in phase and Common black for neutral, common green for earthing complete all as specified and directed by Engr-in-charges. for:- (a) One light/fan/bell point controlled by one, one way switch. |
| 210 | (b) One fan /Exhaust fan, point controlled by one way switch. |
| 211 | (c) One socket outlet 3 pin 6 Amps on same board |
| 212 | (d) One socket outlet 3 pin 6 Amp on independent board |
| 213 | (e) One bell point controlled by one bell push. |
| 214 | All as per item No 200 above but with 2.5 Sq mm single core multistanded copper conductor cable for 3 pin 16 Amp socket outlet on independent board . |
| 215 | S&F switch piano flush type single pole one way 6 Amp ISI Marked. complete all as specified and directed by Engr-in-charges. |
| 216 | S&F Bell, ding dong type AC, 230 volts, single pole complete all as specified and directed by Engr-in-charges. |
| 217 | S&F Bell push 5/6 Amps, flush type complete all as specified and directed by Engr-in-charges. |
| 218 | S&F switch piano flush type single pole one way 16 Amp ISI complete all as specified and directed by Engr-in-charges. |
| 219 | S&F socket outlet 2 in 1, 5 pin, 6 Amp flush type ISI Marked. complete all as specified and directed by Engr-in-charges. |
| 220 | S&F socket outlet 2 in 1, 6 pin, 6 and 16 amp flush type ISI Marked. complete all as specified and directed by Engr-in-charges. |
| 221 | M&L for Ceiling rose, 3 terminal/PVC/ polycarbonate, isolated body. complete all as specified and directed by Engr-in-charges. |
| 222 | M&L for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting. complete all as specified and directed by Engr-in-charges. |
| 223 | S&F LED lamp 9 W complete all as specified and directed by the Engineer-in-Charge. |
| 224 | Supply and fix stepped type electonic fan regulator flush type ISI complete all as specified and directed by Engr-in-charges. |
| 225 | Taking down and refixing / Hanging only ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed by Engr-in-charges. |
| 226 | S&F sheet metal enclosures 240 volt with suitable rated bus bar for double door IP-43 DB's suitable for one MCB SPN as incoming and 6 MCB SP as out going SPN 12 way complete all as specified and directed by Engr-in-charge. |
| 227 | S&F Vertical Distribution Board, double Door, suitable for 'A' Frame FP MCCB 100A made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, TPN 4 way, 415 volts with bus bar rating 300 Amps, dust and vermin proof, suitable for incorporation of MCB’s and MCCB etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed by Engr-in-charges.Note : MCCB & MCB shall be measured and paid for separately. |
| 228 | Supply and Fix MCB Single pole 240V, 10 KA \\"C\\" curve 6-32 Amps ISI marked. complete all as specified and directed by Engr-in-charges. |
| 229 | Supply and Fix MCB Single pole & neutral 240V, 10 KA \\"C\\" curve 63 Amps ISI marked. complete all as specified and directed by Engr-in-charges. |
| 230 | S&F MCCB, 'A' Frame, thermal adjustable magnectic setting, Ics = 75% 25 kA, 415V, 100 Amp, 4 Pole MCCB with over load and short circuit protection, complete all as specified and directed by Engr-in-charges. |
| 231 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-charges. |
| 232 | S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and directed by Engr-in-charges. |
| 233 | S&F in LED light fitting 1 X 12 watt (2feet), decorative ultra slim type, with inegral driver, complete with all accessories and making necessary electric connection from ceiling rose to fitting terminal, complete all as specified and directed by Engr-in-charges. |
| 234 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete including 1.60 mtr long 40mm bore light grade GI pipe mounting bracket made to shape with and including MS clamp of F1 40 mmx6mm with bolts , nuts & washers and conductor to fitting with 3 core 1.5 sqmm pvc insulated cable complete all as specified and directed by Engr-in-charges. |
| 235 | M&L for sub main wiring with PVC insulated and unsheathed 2x 6 Sq mm single core multistrandred copper conductor cable passing through in and including PVC conduit , concealing in walls (by means of chasing including making good existing surface and matching existing surface ) ISI marked and conduit accessaries fixed on surface of wall, ceiling etc, making good the distrurbed surface, incl 6 Sq mm single core copper conductor cable PVC insulated and unsheathed as earth wire. complete all as specified and directed by Engr-in-charges. Note :- Two runs of cable 6 Sqmm and One run of 6 Sqmm along with conduit shall be measured as one unit length. |
| 236 | Taking down and re-fixing only incl connecting electric meters up to 25 amps complete all as specified and directed by Engr-in-charges. |
| 237 | S&F exhaust fan, heavy duty metal body, AC single phase 230 V of size 300 mm sweep complete with louvers including fixing/grouting of frame & connecting with & including 3 core PVC insulated copper conductor flexible cable of size 23/0.0076 (or eq. Size in mm) from ceiling rose to fan complete all as specified and directed by Engr-in-charges. |
| 238 | M&L for Earthing complete with galvanised steel earth plate electrode 60 x x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion . Note : Rates are deemed to be included for necessary earth work , earth pit with RCC cover of size 300X300 x25 mm etc complete all as specified and directed by Engr-in-charges. |
| 239 | Supply and lay in trenches/on wall/on pole/in duct /through protection pipe, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables heavy duty LT cable, 1100 volts grade with aluminium conductor cross sectional area 25 Sqmm 4 core size including retrieving/taking out/taking down old unserviceable cable from duct/trenches/pipes/pole/wall etc. including brick cover and protection pipe and disconnecting the connections. complete all as specified and directed by Engr-in-charges.Note:- Excavation and earth work, sand cushioning,PCC cable cover and protection pipe etc. shall be measured and paid for separately. |
| 240 | Excavating in trenches in hard/dense soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out. complete all as specified and directed by Engr-in-charges. |
| 241 | M&L for dry clean fine river sand as in sand cushioning to underground cable including punning down of sand layer complete all as specified and directed by Engr-in-charges.Note :- Punned thickness shall only be measured and paid. |
| 242 | Supplying and laying un-reinforced precast concrete cable cover, class LV, type 1, flat, size 250x150mm x40 mm complete all as specified and directed by Engr-in-charges. |
| 243 | M&L for galvanised steel tubing, light grade, for protection of cable, laid in trenches/road crossing/floor or fixed to pole/wall with all fittings, of size 40 mm bore. complete all as specified and directed by Engr-in-charges. |
| 244 | M&L for and filling in including spreading, levelling, watering and well romming in layers not exc 25cm of excvated loose soil in treches complete all as specified and directed by Engr-in-charges. |
| 245 | M&L Removal of surplus loose soil from excavated place and deposting at safe side distance not more than 50 meter from excavated place where directed at a level n exc. 1.5m above the starting point complete all as specified and directed by Engr-in-charges. |
| 246 | S&F electric storage water heater of capacity 25 litres BEE 5 star rated Storage type steel body with copper inner tank and heating element upto 2 KW. including proper installing arrangements on wall surface with suitable Anchor Bolt and Geyser connections for Hot and Cold water supply made of stainless steel wire braided connector with chrome finish heavy duty nuts of 15 mm size with suitable length etc complete all as specified and directed by Engr-in-charges. |
| 247 | M&L for road cutting(not more than 3.5 mtr in width of road) and excavation upto 60 cm below ground level and laying of 5 running mtr protection 40 mm dia GI pipe of medium grade and make good distrubuted suface by PCC 1:4:8 (nominal mix), type D-2, using 40mm graded crushed stone aggregate complete all as specified and directed by Engr-in-charges. |
| 248 | S&F socket outlet 2 in 1, 3 pin, 6 Amp flush type ISI Marked. complete all as specified and directed by Engr-in-charges. |
| 249 | S & F sheet metal enclosures 240 volt with suitable rated bus bar for double door IP-43 DB's suitable for one MCB SPN as incomming and 6 MCB SP as out going SPN 8 way complete all as specified and directed by Engr-in-charges. |
| 250 | Supply and fixing MCB TPN 415V, 10KA 'C' Curve 63 Amps complete all as specified and directed by Engr-in-charges. |
| 251 | M&Lfor sub main wiring with PVC insulated and unsheathed 2x 1.5 Sq mm single core multistrandred copper conductor cable passing through in and including PVC conduit , concealing in walls (by means of chasing including making good existing surface and matching existing surface ) ISI marked and conduit accessaries fixed on surface of wall, ceiling etc, making good the distrurbed surface, incl 1.5 Sq mm single core copper conductor cable PVC insulated and unsheathed as earth wire. complete all as specified and directed by Engr-in-charges. Note :- Two runs of cable 1.5 Sqmm and One run of 1.5 Sqmm along with conduit shall be measured as one unit length. |
| 252 | S&F of Heavy duty Exhaust fan steel body AC single phase, 230V size 450 mm sweep, 900 RPM, including blades & frame, louvers with cutting chases on brick wall and grounting with nut bolts complete all as specified and directed by Engr-in-charge. |
| 253 | Supply, laying testing in trenches LT UG XLPE insulated,armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,croos sectional area 16 sqmm 2 core complete all as specified and directed by Engr-in-charges. Note : Earth work and brick work measured and paid separately |
| 254 | Supply, laying testing in trenches LT UG XLPE insulated,armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,croos sectional area 16 sqmm 4 core complete all as specified and directed by Engr-in-charges. Note : Earth work and brick work measured and paid separately |
| 255 | Excvation in trenches not more than 1.5 meter wide and in depth in Soft/loose soil complete all as specified and directed by Engr-in-charges. |
| 256 | Supply and laying Un reinforced Precast concrete cable cover, Type 2 flat size 300 mm x 180 mm x 40mm complete all as specified and directed by Engr-in-charges. |
| 257 | Supply and fix GI tubing medium grade of 40 mm dia for cable protection complete all as specified and directed by Engr-in-charges. |
| 258 | S & F MCCB ,'A' frame thermal adjustable magnectic setting Ics=75% 16 KA, 415 V, 100 Amp, 4 Pole MCCB with over load and short circuit protection. complete all as specified and directed by Engr-in-charges. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysJul 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender