|
| 1 | Civil BOQ |
| 2 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 4 | Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer-in-charge, including compacting each layer by rolling/ramming and watering, all complete as per drawing and direction of Engineer-in-charge |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and 4 shuttering -All work up to plinth level:1:4:8 (1 Cement: 4 coarse sand (zone-III): 8 graded stone aggregate 40 mm nominal size) |
| 6 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15\\" landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 8 | Shuttering and centering forR.C.C. Structure all required work 7 including all cost ofT & P etc. complete work as per building specification and direction of El. |
| 9 | Electrical BOQ |
| 10 | Supply of P.U Painted 9 Mtr. Decorative Pole are made out of G.l Steel Tubes as per MS Base Plate Dia. OD 400 x 12mm, & Alu. Iron Casting on joint, inbuilt Control Box at the bottom of the pole for space for Housing MCB & Terminal strip etc. Specification of Pole Sections: 1st Section 165mm (O.D) x 2000mm (Length) x 3.6mm (thickness) combined 2nd Section 84mm (O.D) x 5000mm (Length) x 3mm Grooved Pipe (Thickness) With Polyurthane Painted color shade Glossy (Black & golden/Copper Golden). Arm Section 60mm (O.D) x 2000mm (Length) x 3mm (thickness) As per Drawing With Arm Total length of pole is 9Mtr. |
| 11 | Providing and fixing Double arm bracket with canopy Total length 3000mm (1500mm Each side) and 42mm dia pipe + Casted Component's dia pipe included P.U Paint. 1.5m long, Arm Bracket (1500mm) Polyurthans Painted Colour shade glossy (Black & goldens) |
| 12 | Supply of P.U Painted 9 Mtr. Solar HyBrid Decorative Pole are made out of G.I Steel Tubes as per MS Base Plate Dia. OD 400 x 12mm, & Alu. With 200Watt x 2 Solar Panel & inbuilt 100Ah lithium ion battery Iron Casting on joint, inbuilt IOT Based controlling with Control Box at the bottom of the pole for space for Housing MCB & Terminal strip etc. Specification of Pole Sections: 1st Section 165mm (O.D) x 2000mm(Length) x 3.6mm (thickness) combined 2nd Section 84mm (O.D) x 5000mm (Length) x 3mm Grooved Pipe (Thickness) With Polyurthane Painted color shade Glossy (Black & golden/Copper Golden). Arm Section 60mm (O.D) x 2000mm(Length) x 3mm(thickness) As per Drawing With Arm Total length of pole is 9Mtr. |
| 13 | SITC of LED Luminaire light 120W, 0-10 Volt Dimmable Luminaire system.>/=100 lm/Watt ingress protection IP66 with 3 year warranty input operating voltage range and frequency 90 to 300 volts AC at 50 Hz Automatic higher cut off voltage above 300 volt rated voltage 230V AC 50 hz AC Power factor at full load.>.95 Driver efficiency up to 100W>85% ABOVE 100W>/=90% Total harmonics distortion<10 Optical LED chip efficacy >130 Im/watt colour temperature 6000+/-500k working life for led minimum 50000 burning hours as per LM-80 and LM21 reports colour rendering index (CRI)> 70 Led beam angle>120 operating temperature range-10 deg C to+50 deg C operating humidity range 10% to 95% RH insulation resistance between earth and current carrying part>100M Ohm the luminaire shall be protected against surges and transients (internal)>/=5 kv inbuilt the luminaire shall be protected against surges and transieents of >/=10 KV(external) luminaries light transparency should be of toughened glass toughned transparent glass cover/4mm light source SMD LED Chip as per LM 80/IS 16106 LED Make OSRAM/NICHIA/CREE/SAMSUNG/SEOUL/LUMI LEDS/ PHILIPS/SYSKA/ LUMENMAX/EVER LIGHT/EDISON/BRIDGELUX/NATION STAR/REFOUND LED DRIVER IP66-EMI, EMC, TTC, TDS, CRS, BIS Approved 0 to 10 Volt Dimmable PHILIPS/OSRAM/MEANWELL OTHER BIS APPROVED MAKE. Furnished Light must TTC, TDS, EMI, EMC, IP 66, LM79, BIS, CRS, ISO, LM 80, ISO Furnished with NABL ULR Number. |
| 14 | Supply of 120W on AC Current & Switching to 60W Hybrid Solar light top suspended lantern range made up of spun aluminum Canopy with Die Cast Aluminum spigot Fitting with glare free optically designed prismatic diffuser and high efficiency LEDs available in 3000K/4000K/6000K 0-10V Dimiing Smart Light. |
| 15 | Supply of Foundation bolt \\"J Type\\" of Size M24X750 mm with Anchor plate 4 pice 1 Set |
| 16 | SLC (R.F) Based for smart lighting control |
| 17 | CCMS Control Panel with 3 year Software support 3 Phase automatic 63 AMP WITH FEEDER STAND. |
| 18 | Bakelite Sheet, Electrical insulator, Aluminium Lughs (4mm), Aluminium Lughs pin (2mm), Set of one Pole |
| 19 | Supplying, installing, testing and commissioning of following capacity TPN tap off box made of 1.6mm thick sheet steel enclosure duly painted with powder coating on existing rising mains complete with TPN disconnector FSU and HRC fuses, connections, earthing etc. as required 100 A TPN. |
| 20 | 1.5 Sqmm unseaihed copper cable 4 core Make. |
| 21 | 4x 10 Sqmm armoured Al cable Make. |
| 22 | 4x 16 Sqmm armoured Al cable Make. |
| 23 | 6 A, to 32 A, ratings, DP MCB, \\"C\\" curve, 10 KA breaking capacity |
| 24 | Earthing with copper earth palte 600mm X 600mm X 3 mm 'thick including accessories, and providing masonry enclosure' with cover plate having locking arrangement and water pipe of 2.7 meter long etc. with charcoal/coke and salt as required |
| 25 | 100 mm diA, G.I. pipe (medium class) |
| 26 | Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/termination with Gl thimble etc. as required. |
| 27 | 20 mm diA, G.I. pipe (medium class) |
| 28 | 50 mm diA, ISI marked, PVC conduit |
| 29 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Upto 35 sq. mm Please Enable Macros to View BoQ information |
