|
| 1 | Dismantling existing plaster including disposal of refuse as directed by the Engineer-in-charge within a distance of 60 metre (200 feet). |
| 2 | First class Brick Work in (1:4) cement & four coarse sand 2.20 F.M. morter in foundation and plinth and T&P etc all completed as per the direction of engineer - in - charge. (AS PER PWD SOR 2022 PAGE NO 20 SI NO 6.05 ITEM NO 305 (a) |
| 3 | 12 mm thick plaster with cement and coarse sand of1.25 fineness modules in (1:4) over brick work minimum thickness not to be less than 1 cm including supply of all material, labour, tools & plant etc required for proper completion of the work. (AS PER PWD SOR 2022 PAGE NO 36 SI NO 13.11 NEW ITEM ) |
| 4 | Scraping old white or colour wash including disposal of refuse as directed by the Engineer-in-charge within a distance of 60 metre (200 feet). |
| 5 | Providing wall putty on old surface with approved quality material of Berger/ J.K./Birla or similar make 2 coats.AS PER PWD SOR 2022 662 NEW ITEM |
| 6 | Distempering (first coat) with oil bound distemper of approved brand and manufacture and ofrequired shade on undecorated wall surface to give an even shade over and including a primingcoat with cement primer of approved brand and manufacture such as Berger, J&N, Shalimar,Asian Paint after thoroughly brushing the surfacefree from mortar dropping and other foreignmatters and also sand papered smooth includingsupply of all materials, labour, Tools & plants etc.required for proper completion of the work.As in item (649) above but for every coat after thefirst coat. |
| 7 | Painting with synthetic enamel paint of approved brand andmanufacture of required colour to give an even shade :13.99.1 One or more coats on old work |
| 8 | Supply and fixing 6 mm. (¼\\") China white glazed tiles in flooring or in skirting or dado laid with 1:3 Cement and approved coarse sand mortar finished with white cement slurry, jointing and polishing complete, including supply of all materials, labour and Tools and Plants. |
| 9 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.(b) Size of Tile 600x600 mm |
| 10 | Chequered terrazo tile 22mm thick (light shade) including 10% wastage carriage of tile |
| 11 | S/L C:C (1:2:4) with 20 mm stone grit, coarse sand & cement etc all complete as the direction of engineer in charge. (AS PER PWD SOR 2022 279 ( a). |
| 12 | Finishing wall with water proof cement paint of approved make and quality on new wood with two coat to give an even shade including supply of all materials, labour, Tools & plant etc. required for proper completion of the work.Same in item no. (660) but for each coat of water proof cement paint after the first two coat to givean even shade. (Snowcem) |
| 13 | M.S. or iron work of small sizes and section such as holding down bolts, hold fast, tie rods grating etc. wrought to required from including supply of steel bolts, nuts wastage etc. and their fixing required for proper completion of the work. |
| 14 | Providing & fixing UV stabilised fiberglass reinforced plastic sheetroofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified12.47.2 2 mm thick flat |
| 15 | GST Please Enable Macros to View BoQ information |
