|
| 1 | Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, dewatering, construction of shoring, shuttering & bracing, removal of stumps & other deleterious material and disposal upto a lead of 50 m, dressing of sides & bottom and backfilling in trenches with excavated suitable material.I Ordinary Soil(i) Upto 3 m depth |
| 2 | Filling in foundation trenches as per drawing & MoRD technical specification Clause 305.3.9, 1200.I Sand filling |
| 3 | Filling in foundation trenches as per drawing & MoRDtechnical specification Clause 305.3.9, 1200.Earth filling (For marshy soil) |
| 4 | Providing concrete for plain concrete (using jhama brick aggregate) in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement)I P.C.C grade M 10 (using jhama brick aggregate)(i) Nominal mix 1:3:6 |
| 5 | Pile load test on single vertical pile in accordance with IS : 2911 (Part - IV)Initial and routine load test |
| 6 | Plain/reinforced cement concrete in substructure complete including formwork as per drawings & MoRD technical specification Clauses 802, 804, 805, 806, 807, 900, 1202 & 1204. (including centering, shuttering, staging etc. but excluding reinforcement)VI. R.C.C grade M-25i) upto 5 m height |
| 7 | Supplying, fitting & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar in substructure complete as per drawings & MoRD technical specification Clauses 1002, 1005, 1010 and 1202. |
| 8 | Backfilling behind abutment, wing wall & return wall complete as per drawings & MoRD technical specification Clause 1204.3.8.I) Sandy material |
| 9 | Providing pressure relief pipes 100 mm dia in bottom slab of box cell on a filter media base of 500 mm x 500 mm as per drawing & MoRD technical specification Clause 1205.5.7. |
| 10 | Providing & laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil & bigger size towards the wall & providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MoRD technical specification clause 1204.3.8. |
| 11 | Providing & laying reinforced cement concrete insuperstructure as per drawings & MoRD technicalspecifications Clauses 800, 900, 1205.4 & 1205.5(including centering, shuttering, staging etc. but excluding reinforcement).II R.C.C M 251 For height upto 5 m |
| 12 | Supplying, fitting, & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar reinforcement in superstructure complete as per drawing & MoRD technical specifications Clauses 1002, 1010 & 1202. |
| 13 | Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawings & MoRD technical specifications Clauses 800 & 1206.3 (including centering, shuttering, staging etc. and reinforcement). |
| 14 | Reinforced Cement Concrete M 25 grade approach slab including reinforcement & formwork complete as per drawing & MoRD technical specifications Clauses 800 & 1211 (including centering, shuttering, staging etc. and reinforcement) |
| 15 | Single bamboo palasiding/walling of whole 2nd class bamboo (Jati or Bethua) 65 to 75 mm dia and closely packed & driven @ 150 mm c/c including fitting fixing with half bamboo kamis horizontally in three rows with cane or tying with wire complete and struts 1.5 m apart longitudinally and providing bitumen drum sheet walling fixed with nails as per drawing and MoRD technical specification Clause 1302.5.Driven at least 900 mm below ground and 1200mm above ground on average |
| 16 | Construction of Embankment with Material Obtained from Borrow PitsConstruction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per MoRD Technical Specification Clause 301.5. |
| 17 | Providing and laying of apron with cement concrete blocks of size as per Table 1300.1 cast-in-situ and made with nominal mix of M-15 grade cement concrete (using jhama brick aggregate)as per drawing and MoRD technical specification Clause 1301 (rate includes preparation of bed,nominal surface re-inforcement and filling of granular material in recesses between blocks). |
| 18 | Bored Cast-in-Situ piles 500 mm dia, M-25 grade RCC pile excluding reinforcement complete as per drawing and technical specification and removal of excavated earth with all lifts and lead upto 1000 m as per MoRT&H specification clause 1100, 1200, 1500, 1700. |
| 19 | Dismantling of StructuresDismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding whenever necessary, sorting the dismantled material, disposal of unserviceable material andstacking the serviceable material with all lifts and upto a lead of 1000 m as per MoRD Technical Specification Clause 202.(II) By Mechanical MeansB) Reinforced Cement Concrete |
| 20 | Providing and fitting, fixing double layer split muli bamboo tatti lining in position as per drawing and specification. |
| 21 | Supplying ballies 100 mm dia well dressed and making shoe with end tappered upto 300 mm from the bottom including marking length and part of a metre as per drawing and specification.ii) 3rd class local wood Ballies |
| 22 | Handling and driving ballies of 100 mm dia upto the length required by heavy hammer as per drawing and specification. |
| 23 | Providing and fitting, fixing ballies of 100 mm dia for horizontal, diagonal bracing, strut etc. with nails/ spikes and binding wire (GI 2.0 mm) as per drawing and specification.ii) 3rd class local wood Ballies |
| 24 | 1700 Painting on Steel SurfacesProviding and applying two coats of ready mix paint including primer coat of approved brand on steel surface after through cleaning of surface to give an even shade as per drawing and MoRD Technical Specification Clause 1701. Please Enable Macros to View BoQ information |
