|
| 1 | S/F of Canada pine including supply and fixing T&P etc |
| 2 | Providing and fixing flat pressed three layer particle or graded plain wood board medium density exterior grade (Grade I) FPT-1, conforming and marked to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately):12mmthick 9.17.1 |
| 3 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal wood 9.1.2 |
| 4 | Melamine polishing on wood work (one or more coat) 13.114 |
| 5 | Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 6 | 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 7 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1 :4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 11.41.4 |
| 8 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In lime mortar 15.7.3 |
| 9 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 25 mm and up to 40 mm15.23.2 |
| 10 | Dismantling tiled roofing with battens, boarding etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres lead 15.31 |
| 11 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 |
| 12 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 6.4.1 Cement mortar 1 :4 (1 cement: 4 coarse sand) |
| 13 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) 13.1.2 |
| 14 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).21.18 |
| 15 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 32 mm nominal dia Pipes 18.8.4 |
| 16 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick Second class teak wood 9.7.1 |
| 17 | Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS: 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer- in-charge and panelling with panels of : (Note:- Butt hinges and necessary screws shall be paid separately)12 mm thick pre-laminated particle board (decorative lamination on both sides) grade -1, medium density flat pressed, three layer particle board FPT- I or graded wood particle board FPT- I, conforming to IS : 3087, bonded with BWP type synthetic resin adhesive as per IS : 848 and pre-laminated conforming to IS : 12823, Grade 1, Type - 11 marked. 9.6.2 |
| 18 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 12.50 |
| 19 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).kiln wood9.1.2 |
| 20 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 12.51.1 |
| 21 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid |
| 22 | Supply and fixing of wash basin with vanity inluding of all material labour t & p etc complete. |
| 23 | Supply and fixing off towel ring inluding of all material labour t & p etc complete. |
| 24 | Supply and fixing of toilet paper holde inluding of all material labour t & p etc complete. |
| 25 | Supply and fixing of hand fauscets inluding of all material labour t & p etc complete. |
| 26 | Supply and fixing of angle valve inluding of all material labour t & p etc complete. |
| 27 | Supply and fixing of short body bib cock inluding of all material labour t & p etc complete. |
| 28 | Supply and fixing of shop disc inluding of all material labour t & p etc complete. |
| 29 | Supply and fixing of looking mirror inluding of all material labour t & p etc complete. |
| 30 | Supply and fixing of shower inluding of all material labour t & p etc complete. |
| 31 | Supply and fixing of towel rack inluding of all material labour t & p etc complete. |
| 32 | Supply and fixing of wash basin mix inluding of all material labour t & p etc complete. |
| 33 | Supply and fixing of wall mix inluding of all material labour t & p etc complete. |
| 34 | s/f of PVC lours wall panelling 6*5*5 incuding material labour t&p etc |
| 35 | supply and fixing wooden flooring quotation including material labour t&p etc |
| 36 | supply and fixing of double bed rate including supplying and fixing of all material t&p etc passed TRH Sukhatal |
| 37 | supply and fixing of dbed head rest 6*8ft including supplying and fixing of all material t&p etc |
| 38 | supply and fixing of LCD Panel including supplying and fixing of all material t&p etc |
| 39 | supply and fixing of Dressing mirror including supplying and fixing of all material t&p etc |
| 40 | supply and fixing of Luggage rack including supplying and fixing of all material t&p etc |
| 41 | supply and fixing of Room chairs 2+1 table including supplying and fixing of all material t&p etc |
| 42 | supply and fixing of ward robe table including supplying and fixing of all material t&p etc |
| 43 | supply and fixing of bed side table including supplying and fixing of all material t&p etc Please Enable Macros to View BoQ information |
