|
| 1 | Surface dressing of the ground including removing vegetation and ineqalities not exceeding 15cm deep and disposal of rubbish lead up to 50m and lift up to 1.5m complete item. DSR-2.31 |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge DSR 2.8.1 |
| 3 | (1 Cement: 4 coarse sand (zone-III) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR No.4.1.8 |
| 4 | providing and injecting chemical emulsion for preconstruction antitermite treatment and creating a chemical berrier under and around the column pits wall trenches basement excavation top surface in plinth filling junctiion of wall and floor along the external perimeter of binding expansion joints surrounding of pipes and conduits etc DSR 2.35.3 |
| 5 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth In: Cement mortar 1:6 (1 cement: 6 coarse sand) DSR-6.1.2 |
| 6 | Earth work by mechinical/manual means in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with tonne roller or wooden or steel rammers, and rolling overy 3rd and top-most layer with power roller of minimum 8 onnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and for all lift All kinds of soil DSR-2.2.1 |
| 7 | RC.C Work with cement, approved coarse sand & 2cm gauge approved stone grit in proportion of 1:2:4 in lintels of door & window excluding supply of reinforcement and its cutting and bending, but including its fixing and binding the same with 24 B.W.G.G.I binding wire and including necessary centring and shuttering etc and supply of all materials, labour, Tools & Plants etc. required for proper completion of the work including cost of binding wire.DSR No.5.1.3 |
| 8 | RCC(1:1.5:3) in Column with cement coarse sand and stone grit Complete item. DSR No.5:22 |
| 9 | M.S (Torsteel or plain) ion plain work such as RC CoRB work including cutting/ bending for proper shape as 11 necessary Including supply of all steel & wastage bend hook & authorised overlapping shall be measured.. Complete item. DSR no - 5.22.1 |
| 10 | M-150 Brick Work Brick Work In 1:6 cement Coarse sand superstructure Complete itemDSR No.6.4.2 |
| 11 | M-150 Brick Work Brick Work In 1:4 cement Coarse sand superstructure Complete itemDSR No.6.4.1 |
| 12 | Providing and fixing MS. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size. Including fixing of necessary butt hinges and screws and 14 applying a priming coat of approved steel primer Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3.6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) DSR 10.15.1 |
| 13 | Fixing of door in proper position |
| 14 | Fixing of window in proper position |
| 15 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per 18 IS: 1868), transparent or dyed to required colour or shade. with nuts and screws etc complete 250mm x 16mm 9.96.2 |
| 16 | Providing and fixing aluminium tower bolts, ISI marked. anodised (anodic coating not less than grade AC 10 as per 19 IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 250mm x 10mm 9.97.2 |
| 17 | Providing and fixing aluminium tower bolts, ISI marked. anodised (anodic coating not less than grade AC 10 as per 19 IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 250mm x 10mm 9.97.2 |
| 18 | 12 mm thick Plaster in 1:4 cement sand in ceiling complete item. DSR-13.1.1 |
| 19 | 12 mm thick Plaster in 1:6 cement sand complete item. 22 DBR-13.1.2 |
| 20 | Provinding and fixing 1st quality ceramic glazed floor tiles of size 300 x 300 mm conforming to is: 15622 (thickness to be specified by the manfacturee) of approved make, in all colour shades except 23 white, Ivory.grey fume red brown laidon 20 mm thick bed of cement mortar 1:4 and jointing with grey slurry 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete PWD/DSR 11.38 |
| 21 | Provinding and fixing 1st quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manfacturee) of approved make, in all colour shades except burgundy, bottle black of any size as 23 approved by engineer in charge in skirting risers of steps and dados over 12 mm thick bed of cement mortar 1:3 and jointing with grey slurry @ 3.3 kg per sqm Including pointing in white cement mixed with pigment of matching shade complete PWD/DSR 8.31 |
| 22 | water proffing |
| 23 | 20 mm thick cement plaster in 1:2 cement coarse sand finished with neat cement in dado/skirting... complete item. DSR13.9.2 |
| 24 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws DSR 9.21.1 |
| 25 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm.M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineerin- Charge. (DSR: 9.119) |
| 26 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 26 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rall & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the |
| 27 | Painting on new iron work in two coat with one coat priming with approved superior quality ready mix synthetic enamel paint including supply of all material and labour etc. required for proper completion of work. |
| 28 | Providing wall putty on new surface with approved quality of Berger/J.K/Birla or similar make in two coats. DSR13.8 |
| 29 | Distempering (two coat) with oil bound distemper of approved brand and manufacture and of required shade on undecorated wall surface to give an even shade over and including a priming coat with cement primer of approved brand and manufacture such as Berger, J&N, Shalimar, Asian Paint after throughly brushing the surface free from mortar dropping and other foreign matters and also including the surface even with plaster of Paris of approved synthetic materials and sand papered smooth including supply of all materials, labour, T&P etc. required for proper completion of the work. DSR-13.10.1 |
| 30 | P/Fixing of 100mm PVC RWP down pipe with clamping and 28 bend shoes etc Complete. (S.1-730a, miscellaneous) |
| 31 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 32 | (a) Lintels, beams, plinth beams, girders, bressumers and cantilevers DSR 5.9.5 |
| 33 | (b) Foundations, footings, bases of columns, etc. for mass concrete DSR 5.9.1 |
| 34 | (c) Columns, Pillars, Piers, Abutments, Posts and Struts DSR 5.9.6 |
| 35 | (d) Suspended floors, roofs, landings, balconies and access platform.DSR 5:9.3 |
| 36 | Supply and fixing of Board |
| 37 | SANITARY ITEMS |
| 38 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (DSR 18.9) |
| 39 | External work |
| 40 | 32mm nominal outer dia pipe |
| 41 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings. Uc fixing the pipe with clamps at 1.00 m spacing This Includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints |
| 42 | Concealed work, including cutting chases and making good the walls |
| 43 | 20mm Nominal outer dia pipes |
| 44 | 25mm Nominal outer dia pipes |
| 45 | Making connection of G.I. distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: |
| 46 | 25 to 40 mm nominal bore (DSR 18.13.1) |
| 47 | Providing and fixing 25mm thick PVC flush door shutter made out of one plece multi chamber extruded PVC section of the size of 762mmx25mm or less as per requirement with an average wall thickness of 1mm etc all omplete. (DSR 9-118-3) |
| 48 | 6 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron Por S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to 15 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required floors wherever required: |
| 49 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C flushing cistern, including flush pipe. with manually controlled device (handle lever), conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 50 | W.C. pan with ISI marked white solid plastic seat and lid (DSR 17.2.1) |
| 51 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls |
| 52 | White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. (DSR) |
| 53 | Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer |
| 54 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick Circular shape 450 mm dia (DSR) 17.32.1) |
| 55 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: (DSR 18.49.1) |
| 56 | Providing and fixing uplasticised PVC connection pipe with brass unions |
| 57 | ELECTRIC ITEM |
| 58 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 15 sq.mm FRLS PVC Insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 59 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC Insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required |
| 60 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 61 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 62 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 63 | Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 & 15/16 A Each modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 64 | Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A Each modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 65 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as resquired, (for A.C. Point/MCB Point) |
| 66 | Supplying and fixing following 8 way, SPN Dustribution Box sheet steel, MCB distribution board, on surface/ recess, complete 8 way SPN, Double door |
| 67 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circult breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 68 | Supply and fixing of 63 Amp. FP MCB (10 KA) C Curve. CAT A |
| 69 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 70 | Supplying and laying 25 mm X 5 mm G.1 strip at 0.50 metre below ground as strip earth electrode, Including connection/ terminating with G.1. nut, bolt, spring, washer etc. as required. (Jointing, shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 71 | Providing and laying earth connection from earth electrode with 6 SWG día G.I. Wire in 15 mm dia G.1. pipe from earth electrode including connection with G.I. Mtr thimble excavation and re-filling as required, |
| 72 | Supply, Installation. Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos, canopies, shackle kit. safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per 15: 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise-75 degree C (max.), insulation resistance more than 2 mega ohm. suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 73 | Supply & fixing of recess mounting round 15 to 18 watt LED down Lighter having Powder coated die cast aluminium housing with heat sink diffuser /reflector and driver set complete in all respect CAT.-AAA |
| 74 | Supplying and laying of aluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top On surface the cable run shall be fixed on MS clamps etc. of suitable size or as directed by the Engineer-Incharge complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps |
| 75 | Supply & fixing of 225/300mm sweep ventilating (Light Duty) exhaust fan complete with Metallic Blade (Steel bird guard protector/Copper motor for high air suction performance /Capacitor etc.), Noise level (4550) dB, Power consumption: 45 W, Rated voltage: 230 V, Rated frequency: 50 Hz. Motor type: Normal Speed. Complete in all respec |
| 76 | S/F of changeover switch on angle iron frame 100 Amp 4 pole... complete. Sch. Please Enable Macros to View BoQ information |
