|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. 2.6.1 All kinds of soil (DSR- 2023) |
| 2 | Providing and laying cement concrete in 1:4:8 ( 1 cement : 4 fine sand : 5 graded stone aggregate 40mm nominal size) and curing complete, including cost of iron work in foundation and floors completion of the work as per direction of E/I. . (Dsr-2023 4.1.8 ) |
| 3 | Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions ions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete . All works upto plinth level: Concrete of M20 grade with minimum cement content of 270 kg /cum (DSR 2023- 4.20.1.3) |
| 4 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 5.33.1 All works upto plinth level 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum (DSR-2023) |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for DSR 2023- 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 6 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. DSR 2023 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 7 | Earth work in cutting or in embankment in ordinary soil, excavation to be in the form of regular pits not exceeding 0.50 M in depth & earth-work in embankment to be in 20 Cm layers including ramming and dressing the surface to required levels and slopes and also including 1.5 M lift and 30 M lead. The earth from cutting to be used in making embankment or to be deposited as spoil banks within 30 M distance as directed by the Engineer-in-charge. (Analysis Attached) |
| 8 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres DSR 2023-16.1 |
| 9 | Construction of granual sub base (GSB) by providing coarse graded material spreading in uniform layers with moter grader surface, mixing by mix in place method with rotavator at OMC & compacting with vibratory power roller to achieve the desired density, complete as per clause Table-400-2 S.N. 4.2 (C) MORT&H specification no. 401(For Grading-I), 53mm-26.5mm, 35.00%, 26.5mm - 4.75mm, 45%, 2.36mm and below 20%.(PSR) |
| 10 | Providing, laying spreading & compacting graded stone aggregate of approved quarry to wet mix macadam (WMM) specification including premixing the material with water at O.M.C in machenical mix plant carriege of mixed material by tipper to site, lating in uniform layers with paver in sub -base /base course on well prepared suface & compacting with vibroatory roller to achieve the desired density complete as per MoR &H clause 406& as directed by Engineer Incharge including all machine charges & including all labour, T& P etc req for proper completion of work. (PSR) |
| 11 | Providing, & applying Priming Coat with bitumen emulsion(SS1) on prepared surface of grangular base including cleaning of road surface and spreading primer @ 0.70 kg/sqm. using mechanical means. Rates including of bitumen emulsion. (As per MORTH 502 , MORT&H 2024 Rates taken from SOR 2025-26)(Analysis Attached) |
| 12 | Providing and laying Dense Graded Bituminous Macadam with higher capacity batch type HMP using crushed stone aggregates of specified grading, premixed with Bituminous binder(VG-30) @4.5% by weight of total mix and filler,transporting the hot mix to work site, laying with hydrostatic paver finisher with sensor control to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density as per MORTH specification clause No. 505 (MORT&H 2024 Rates taken from Sor 25-2026)(Analysis Attached) |
| 13 | Providing, & applying Tack coat with bitumen emulsion SS1 using emulsion pressure distributor @ 0.25 kg/sqm on the prepared grangular/ old painted surface, cleaned with mechanical broom including all Taxes material, labour, T& P etc. required for proper completion of work. Rates including of (As per MORTH 503 MORT&H 2024 Rates taken from Sor 25-2026)(Analysis Attached) |
| 14 | Providing and laying Bituminous concrete with higher capacity batch type hot mix plant using crushed stone aggregates of specified grading, premixed with Bituminous binder (VG-30) @5.4% by weight of total mix and filler, transporting the hot mix to work site, laying with paver finisher with sensor control to required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. as per MORT & H specification clause no. 507. MORT&H 2024 Rates taken from Sor 25-2026)(Analysis Attached) |
| 15 | Providing and fixing PVC pipe conforming to lS make working pressure 6 KgiSqCm incuding testing labour T&P and all complete fittings. 110 dia CH-23 SR.NO 30(C) (SOR-2023-24) |
| 16 | Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. DSR-2023 16.62 Please Enable Macros to View BoQ information |
