|
| 1 | [12.1.1.1]Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or dash fastener shall be paid separately). 1.1. Second class teak wood [Through Rate] |
| 2 | [12.114]Providing and fixing of roller blinds on windows complete with material and labour complete with push up and down arrangement as per approved design / colour and Engineer-in-charge. [Through Rate] |
| 3 | [12.171]Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top and bottom pivot and double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). [Through Rate] |
| 4 | [22.86.1]Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 1. 15 mm nominal outer dia Pipes [Through Rate] |
| 5 | [23.22.4.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.3. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. SPN DB Double Door 12 way ( 2 incoming and 10 outgoing) [Through Rate] |
| 6 | [23.22.4.5]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 4.5. Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 4 way ( 8 incoming and 3phase*4 outgoing) [Through Rate] |
| 7 | [23.22.5.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole [Through Rate] |
| 8 | [23.22.5.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.3. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Double POLE [Through Rate] |
| 9 | [23.22.5.4]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.4. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. Double pole [Through Rate] |
| 10 | [23.22.5.5]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.5. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp MCBs TRIPLE POLE [Through Rate] |
| 11 | [23.22.5.7]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.7. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp MCBs FOUR POLE [Through Rate] |
| 12 | [23.22.5.8]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.8. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. MCBs FOUR POLE [Through Rate] |
| 13 | [23.23.5.1]MISCELLANEOUS 5.1. Supply and erection of U- PVC Trunking/Channel of following size including cost of fixing on wall, floor and ceiling etc. with required material complete the job in all respect up to entire satisfaction of the Engineer-in-charge of work. 25x12 mm [Through Rate] |
| 14 | [23.23.5.4]MISCELLANEOUS 5.4. Supply and erection of U- PVC Trunking/Channel of following size including cost of fixing on wall, floor and ceiling etc. with required material complete the job in all respect up to entire satisfaction of the Engineer-in-charge of work. 50x50 mm [Through Rate] |
| 15 | [23.23.8.1]MISCELLANEOUS 8.1. Supply and laying of multicore telephone cable conductor size 0.51 mm bright annealed copper conductor PVC insulated and sealed in existing pipe/channel and making necessary connection complete in all respect up to the entire satisfaction of the Engineer-in charge of the work. 2 pair telephone wire [Through Rate] |
| 16 | [23.23.9]MISCELLANEOUS 9. Supplying and drawing of 1 no UTP 4 pair CAT 6 LAN Cable in the existing surface/recess MS/PVC conduit as required [Through Rate] |
| 17 | [23.28.1.3]Supplying, installation, Testing and Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency )85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short and Open circuit protection ,THD ( 10% , P. F.=0.95, IP20, CRI )80 , UGR (Unified Glare Rating) ( 19, Flicker free (flicker should be below 5%), life time (LED,Driver and electrical circuitary), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K / 6000°K / 6500°K (As per ANSI Bin),SDCM (Standard Deviation Color Matching) (3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy =105 and (120 lm/Watt output . LM79 and LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C) 3. Powder coated die cast /Extruded aluminum Body including trim 12-15 watt [Rate] |
| 18 | [23.28.11.1]Supplying, installation, Testing and Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency )85% ,Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range - 15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short and Open circuit protection ,THD ( 10% , P. F.=0.95, IP20, CRI )80 , Flicker free (flicker should be below 5 %), life time (LED,Driver and electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6000°K/ 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) (3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy )135 lm/Watt output . LM79 and LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer- in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). 1. Powder coated die cast /Extruded aluminum Body (Thickness >= 1.20 mm) 18-22 Watt [Rate] |
| 19 | [23.28.5.3]Supplying, installation, Testing and Commissioning of LED Recessed /surface Down lighter (Round / square/ Rectangular) COB Type of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency )85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short and Open circuit protection ,THD ( 10% , P. F.=0.95, IP20, CRI )80 , UGR (Unified Glare Rating) ( 19, Flicker free (flicker should be below 5 %), life time (LED,Driver and electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) (3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. `complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy =120 (135 lm/Watt output . LM79 and LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). 3. Powder coated die cast with Aluminium Reflector 12-15 watt [Rate] |
| 20 | [23.28.6.4]Supplying, installation, Testing and Commissioning of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency )85%, Operating voltage AC 140- 270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 degree centigrade, internal surge protection of 2.5 KV with Short and Open circuit protection, THD ( 10% , P. F.=0.95, IP20, CRI )80, UGR (Unified Glare Rating) ( 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver and electrical circuitry), of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6000°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) (3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy =105 (120 lm/Watt output . LM79 and LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). 4. Powder coated die cast / Extruded aluminium Body (Thickness >= 1.20 mm) 36 watt [Rate] |
| 21 | [23.33.1 (a).2]Online UPS - Input supply: Single Phase, Output Supply : Single PhaseSupplying, installation, Testing and Commissioning of following capacity at full load (Unity Power Factor) ON LINE Uninterrupted Power Supply (UPS) system suitable for Single Phase input, Single Phase output AC Supply. The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for manual bypass, suitable isolation transformer for additional protection against neutral faults etc. The UPS systems shall be Microprocessor based Digital Control, using Insulated Gate Bipolar Transistor (IGBT)`s both for the rectifier and inverter with PWM (Pulse Width Modulation) Technology. The quality of design, manufacturing and inspection process should confirm to the relevant Inter-national standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be )95% at 100% non-linear loads. Current total harmonic distortion (ITHD)/ total demand distortion (TDD) on the input grid shall be ( 5% at 100 %load. (The required LC filters shall be included in UPS cost), extreme power factor kit to be include to limit the input pf to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ) however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC single phase 160-270V 50 Hz and delivering output AC supply true sine wave single phase 220/230/240 Volt, 50 Hz plus /- 0.2Hz, Overload capacity of 120% for 10 mins and 150% for 1 minute.Operating temperature 0 to 40 deg C, Relative humidity 0-95% non condensing, noise level less than 60db at 1 meter distance, Protection for Under voltage, over voltage, abnormal output voltage, battery over charging, output over current, short circuit, battery deep discharge, 10 KV surge. Display for watt/VA, Amp and Voltage power parameters etc. UPS shall comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI) type UPS (as per standard IEC 62040-1, 2 and 3). The UPS should be with IGBT Based Inverter Technology, Communication RS232/RS485/SNMP port open protocol for BMS integration as per approved by Engineering in charge. Required battery racks, DC breaker of suitable rating and interconnecting copper conductor cable of suitable size and connectors and all required accoseries are inclusive in the cost. The UPS should have QR code which should contain drawing, test report OEM manual, Geo- Tag of manufacturing location etc 2. 3KVA [Rate] |
| 22 | [23.5.6.1]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.1. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) [Through Rate] |
| 23 | [23.5.6.2]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.2. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 2.50 Sqmm(1.1.80mm) [Through Rate] |
| 24 | [23.5.6.3]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.3. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 4 Sqmm(1/2.24mm) [Through Rate] |
| 25 | [23.5.6.5]COPPER WIRING IN EXISTING PVC/MS CONDUIT PIPE SURFACE/RECESSED FOR ELECTRICAL POINTS 6.5. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 10 Sqmm(1/3.50 mm) [Through Rate] |
| 26 | [23.7.6.2]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. [Through Rate] |
| 27 | [23.7.6.3]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.3. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 32 mm dia. [Through Rate] |
| 28 | [23.8.10.1]FITTING AND ACCESSORIES 10.1. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 1 & 2 Modules including combined plate for Telephone and data [Through Rate] |
| 29 | [23.8.10.2]FITTING AND ACCESSORIES 10.2. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 3 Modules [Through Rate] |
| 30 | [23.8.10.3]FITTING AND ACCESSORIES 10.3. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 4 Modules [Through Rate] |
| 31 | [23.8.10.4]FITTING AND ACCESSORIES 10.4. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 6 Modules [Through Rate] |
| 32 | [23.8.10.5]FITTING AND ACCESSORIES 10.5. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 8 Modules [Through Rate] |
| 33 | [23.8.11.1]FITTING AND ACCESSORIES 11.1. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch [Through Rate] |
| 34 | [23.8.11.10]FITTING AND ACCESSORIES 11.10. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. Blanking plate [Through Rate] |
| 35 | [23.8.11.11]FITTING AND ACCESSORIES 11.11. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modular type [Through Rate] |
| 36 | [23.8.11.3]FITTING AND ACCESSORIES 11.3. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 1 way switch [Through Rate] |
| 37 | [23.8.11.4]FITTING AND ACCESSORIES 11.4. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp Socket [Through Rate] |
| 38 | [23.8.11.5]FITTING AND ACCESSORIES 11.5. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 15 amp 6 pin Socket [Through Rate] |
| 39 | [23.8.12]FITTING AND ACCESSORIES 12. Supply and Fixing 3 mm thick Bakelite sheet cover on existing MS/PVC junction box/tee etc including fixing with brass screws and washers. [Through Rate] |
| 40 | [23.8.2.2]FITTING AND ACCESSORIES 2.2. Supply and Fixing Bakelite sheet on existing MS/GI/wooden/PVC box etc including fixing with brass screws and washers. 3 mm thick [Through Rate] |
| 41 | [24.1.10]EARTHING AND LIGHTENING ARRESTOR 10. Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate] |
| 42 | [24.1.4]EARTHING AND LIGHTENING ARRESTOR 4. Earthing with tinned copper earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete as required. [Through Rate] |
| 43 | [24.1.5]EARTHING AND LIGHTENING ARRESTOR 5. Extra for charcoal or coke and salt for G.I. plate or copper plate earth electrode. [Through Rate] |
| 44 | [24.2.6.5]LT CABLE 6.5. Supply and erection of copper lugs including crimping etc. entire satisfaction of Engineer-in- Charge of the work. 10 sqmm [Through Rate] |
| 45 | [25.10.14.1]COPPER REFRIGERANT PIPING Supplying, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 1. 6.4 mm dia (OD)(SOFT) with tube thickness 1.2 mm [Rate] |
| 46 | [25.10.14.3]COPPER REFRIGERANT PIPING Supplying, Installation, testing and commissioning including vaccumization and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 3. 12.7mm dia (OD)(SOFT) with tube thickness 1.2 mm [Rate] |
| 47 | [25.11.4.9]CASSETTE TYPE SPLIT UNITS Supplying, Installation, Testing and Commissioning of Air Cooled Cassette type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), R-32/R410A/R-407 Green Refrigerant, wireless Remote, inbuilt drain pump, suitable for 230/415V plus 10%, 50 Hz ,1 /3 phase AC supply, including surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 5.5 Mtr (IDU to ODU), copper power and control cable upto 5.5 Mtr (IDU to ODU) including drain pipe, the system shall be capable of performing cooling, dehumidification, Air circulation, filtration and ventilation of following capacity with Scroll/rotary compressor with min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB) as specified. The system shall be able to deliver 100% of the rated capacity as per relevant IS Code. The lab testing reports as per IS: 1391 shall be submitted from National Accreditation Board for Testing and Calibration Laboratories (NABL) accredited as per International Electro technical Commission (IEC) 17025 standards/Central Power Research Institute (CPRI)/ Electrical Research and Development Association (ERDA)with Original Equipment Manufacturer (OEM) etc. complete as per CPWD specification and as per IS: 1391 as required. 9. Heating & Cooling 2.5 TR with 3 Star BEE Rating [Rate] |
| 48 | [4.40.5]Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : 5. Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same. [Through Rate] |
| 49 | Providing and fixing wooden flooring 8mm thick victor make with 1mm thick foam complete in all respect |
| 50 | P/F PVC wall paneling complete in all respect |
| 51 | Hall Ceiling Specification :- Providing and Fixing 15 mm thk White Compressed Glass Fibre Panel Square edge combination of 12.5 mm painted gypsum board and light weight ceiling tiles having NRC upto 0.95 of size 595x595 mm in true horizontal level suspended on inter locking metal grid of hot dipped glvanised steel sections (galvanising @120 grams per sqm including both side) consisting of main `T` runner suitably spaced at joints to get required lenght and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm center to center, and cross `T` of size 24x38 mm made out of 0.33 mm (minimum ) sheet, 1200 mm long spaced between main `T` at 600 mm and size 24x38 mm made form a grid of 1200x600 mm and secondry cross `T` of lenght 600 mm and size 24x28 mm made of 0.33mm thick (minimum) sheet to be inter locked at middle of the 1200x600mm panel to from grid of size 600x600mm, resting on peripheriy walls/partitions on a perimeter wall angles precoated steel of size (24x24x3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 c/c with 25 mm long dry wall screws @230 mm interval and laying 15 mm thick Glass Fibre Square edges ceiling tiles in the grid including, cutting/ making opening for services like diffuser ,grills, light fitting,fixtures,smoke detectors etc. wherever required Main T runners to be suspended from ceiling using G.I slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fastener, 4 mm G.I. adjustable rods with galvanized steel level clips of size 85x30x0.8 mm,spaced at 1200 mm center to center along main `T`, bottom exposed with 24 mm of all T sections shall be pre painted with polyester backed paint for all heights as per specification drawing and directed by engineer-in-charge. (Make: Anutone ,Earcons Acoustic , Echophon) |
| 52 | Chair revolving with Arms seat cushioning back wooden shisham/kikar/teak finished with lecquer polish |
| 53 | Supply and Erection of 1.5 mm sqmm x 3 core PVC insulated multi core copper conductor flexible cable (unarmoured) of 1100 volts grade (round) in existing pole/ pipe, complete in all respect including making necessary connections |
| 54 | Medium Back Chair, Pipe Frame, PU Chrome Arm, Gas Lift, Chrome Base, Leatherette Tapestry on Seat and Back. Swivel Tilt Mechanism. |
| 55 | Low Back Chair, PU Arm, Silver Powder Coated Frame, Gas Lift, Powder Coated Base, Mesh Back and Seat Fabric Tapestry, Swivel Tilt Mechanism. |
| 56 | SITC of delegate unit shall be a desktop-style conference microphone unit, supplied complete with a base and detachable gooseneck microphone with Mute/Unmute, delegate priority touch and delegate canceling touch functionality. The unit shall operate at a working voltage of DC 24V and utilize RJ45 cabling. It shall incorporate a cardioid or better capsule with a sensitivity of -46 dBV/Pa and provide a frequency response from 20 Hz to 20 kHz. The input impedance shall be 2 k?, with directional response at 0°/180° greater than 20 dB at 1 kHz. The equivalent noise level shall not more than 20 dBA SPL, maximum sound pressure level shall reach 125 dB with signal-to-noise ratio shall be greater than 80 dB, cross talk shall be greater than 80 dB, and total harmonic distortion shall remain below 0.05%. The unit shall be equipped with a 2.4-inch or bigger IPS TFT display and provide audio output through a 3.5 mm earphone jack supporting loads above 10 ?, with an output power of 10 mW, while the gooseneck microphone shall be 420 mm or more in length with dual adjustment band and lighting indication should be in ON/OFF touch and gooseneck both, etc. complette with all labour and petty material required to complete the job upto entire staisfaction of E-I-C of Work . Approve Make: Byerdynamic/ AudioTchnica/ Clarilus |
| 57 | SITC of chairman unit shall be desktop-style conference microphone unit, supplied complete with a base and detachable gooseneck microphone with Mute/Unmute, delegate priority touch and delegate canceling touch functionality. The unit shall operate at a working voltage of DC 24V and utilize RJ45 cabling. It shall incorporate a cardioid or better capsule with a sensitivity of -46 dBV/Pa and provide a frequency response from 20 Hz to 20 kHz. The input impedance shall be 2 k?, with directional response at 0°/180° greater than 20 dB at 1 kHz. The equivalent noise level shall not more than 20 dBA SPL, maximum sound pressure level shall reach 125 dB with signal-to-noise ratio shall be greater than 80 dB, cross talk shall be greater than 80 dB, and total harmonic distortion shall remain below 0.05%. The unit shall be equipped with a 2.4-inch or bigger IPS TFT display and provide audio output through a 3.5 mm earphone jack supporting loads above 10 ?, with an output power of 10 mW, while the gooseneck microphone shall be 420 mm or more in length with dual adjustment band and lighting indication should be in ON/OFF touch and gooseneck both, etc complette with all labour and petty material required to complete the job upto entire staisfaction of E-I-C of Work .Approve Make: Byerdynamic/ AudioTchnica/ Clarilus |
| 58 | SITC of Central Conference control unit, shall operate on AC 100–240V, 50/60Hz power supply and provide a frequency response from 20 Hz to 20 kHz, signal-to-noise ratio shall be greater than 96 dBA and total harmonic distortion shall remain below 0.05%, equipped with one USB recording connector, four or more DIN-8 input connectors, and four or more RJ45 group connectors. It shall include RS-232 (3P) connectors for both central controller and camera switch, and optionally support HDMI 4×1 video input. Camera control shall be provided through a 6P connector, while computer connectivity shall be available via USB and RJ45. The built-in alarm integration interface shall consist of two 2P connectors (5V plus Audio), Audio input shall be supported through one 2P unbalanced connector and one RCA unbalanced connector and output shall include one 3P balanced connector, two 2P unbalanced connectors, one XLR balanced connector, one 6.35 mm unbalanced connector, one RCA unbalanced connector, one coaxial connector, and one optical fiber connector. The unit shall also incorporate a sound card with USB and RCA (unbalanced ×2) interfaces, shall be built on advanced digital processing with inbuilt digital signal processor for better audio output and transmission technology, fully compliant with IEC60065 international standards with powered by a 1.4 GHz industrial-grade embedded processor with 1 GB memory to ensure high-speed performance and smooth system response system scalability, Touch screen: 4.3-inch or bigger full-view IPS capacitive touch screen, accommodating up to 240 units per host interface and a total system capacity of 76,800 units, with flexible connection methods. Leadership control shall be unlimited, with configurable speaker limits from 1 to 20 and no restrictions for chairman or VIP units with eight intelligent conference modes including FIFO, LIFO, quantity limit, chairman permission, voice activation, timed speech, queuing, and free discussion, ensuring adaptability to diverse meeting styles. Camera integration shall support PELCO-D/P, SONY, SAMSUNG, and other protocols, with tracking, preset positions, RS-232/RS-485 control, and HDMI/SDI matrix switching for cameras, etc. complete required as per specifications. Approve Make: Byerdynamic/ AudioTchnica/ Clarilus |
| 59 | SITC of Digital Conference connecting cable connecting with all labour and petty material required to complete the job upto entire satisfaction of EIC of work |
| 60 | SITC of Digital cable connector IO module for loop in loop out complete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work |
| 61 | SITC of Digital Signal Processor with a minimum of 2 or more microphone/line inputs that include phantom power. It should also have 2 or more-line outputs, should have at least 2 channels of USB input and output for software video conferencing. The sampling rate should be 48kHz or better and the DSP should be expandable for port expansion. It should have a minimum of 4x4 Dante channels for digital audio transfer and comply with CE, FCC, CA, RoHS, and REACH regulations. The DSP should support control with an app via iOS and Android devices or any third-party control system. Additionally, it should have built-in filters, feedback suppression, and other necessary features as per specifications. single-device(chassis) use is permitted, but the combination of devices is not accepted. Should include surface-mount bracket . complete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work. Approved Make: Crestron/Extron/Xilica |
| 62 | SITC of the PTZ camera shall support multiple signal systems, including HDMI output with resolutions up to 4KP30, 4KP25,1080P30, 1080P25, etc., 1/2.5 inches, CMOS, with effective pixels of 8.51 megapixels and operate in progressive scanning mode, 12X optical zoom and 16X digital zoom, with a minimum illumination requirement of 0.5 Lux at F1.8 with AGC ON, shutter speed shall range from 1/30s to 1/10000s, support multiple white balance modes including Auto, Indoor, Outdoor, One Push, and Manual, along with backlight compensation and 3D digital noise reduction, signal-to-noise ratio shall be =55dB. Pan angle shall be ±170° with tilt angle ranging from -30° to plus 90°, and both pan and tilt speeds adjustable between 1.7° and 100° per second. The lens shall be 12×, f4.4mm~52.8mm, F1.8~F2.6, with a horizontal field of view from 71° ~ 8.2° and vertical field of view from 42.7° ~ 4.5°. Supported video formats shall include YUY2 up to 1080P30, MJPEG up to 2160P30, and H.264 AVC up to 2160P30. The camera shall support image flip, image freeze, up to 255 preset positions with 0.1° preset accuracy. The I/O interfaces shall include one 1 x USB 3.0: Type-C, one 1 x HDMI 1.4b, one RJ45 adaptive Ethernet port (10M/100M/1000M), one line-in, and a JEITA type DC IN 12V power interface. Control interfaces shall include 1 x RS485 IN: 2pin phoenix port, Max Distance: 1200m, Protocol: VISCA / Pelco-D / Pelco-P 1 x RS232 IN: 8pin Mini DIN, Max Distance: 30m, Protocol: VISCA / Pelco-D / Pelco-P, The USB specification shall ensure compatibility with Windows 7 (only supports UVC1.1 features), Windows 8 and above version, MacOS 10.5 and above version, Linux 2.4.6 and above version, Android needs to include the version of UVC related drivers. Supported compression formats shall include YUY2, H.265, H.264, and MJPEG, with UVC/USB audio support and UVC video communication protocol versions 1.1 to 1.5. USB video formats shall include YUY2 up to 1080P5, H.264 up to 2160P30, H.265 HEVC up to 2160P30, and MJPEG up to 2160P30. UVC PTZ control shall be supported. Network specification shall include video compression formats H.265, H.264, and MJPEG, with dual video streams. The first stream shall support resolutions up to 3840×2160, 1920×1080, 1280×720, and 1024×576, while the second stream shall support resolutions including 720×576, 720×480, and 320×240. The video bit rate shall range from 32kbps to 51200kbps for the first stream and 32kbps to 20480kbps for the second stream, with support for both VBR and CBR bit rate control. Frame rates shall be adjustable from 1fps to 50fps at 50Hz and 1fps to 60fps at 60Hz. Audio compression shall include AAC and G711A, with audio bit rates of 96Kbps and 128Kbps. Supported protocols shall include NDI®HX2, SRT, TCP/IP, HTTP, RTSP, RTMP/RTMPS, Onvif, DHCP, and multicast, input voltage DC 12V/DC 5V/PoE (802.3af), etc complete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work.Approve Make: Vaddio/ Clearone/ Clarilus |
| 63 | SITC of Touch-Interactive touch flat panel display of size 86`, Back Light Direct Type, Aspect Ratio, 16:9, Resolution3,840 × 2,160 (UHD), Brightness (nits) 500, Contrast Ratio 16,000:1, Touch Type -, Ultra Fine IR, Surface Hardness - 9H, Android 14.0 with Google-EDLA (Actual Certified), Quad, Core Processsor, 8GB RAM, 128GB ROM, Viewing Angle (H × V)178 × 178, Color Depth 10 bit, (D), Display Colours 1.07 Billion , Response Time 6ms , 40 Touch Points (Android), Air Gap - Gen, 2 Zero Bonding (0-0.8mm), Ambient Light Sensor, Wifi (Optional), Inputs - HDMI2.0x3, VGAx1,, DPx1, USB-A, USB3.0x4, USB-Cx2, Audio 3.5mm, Mic Audio x1,RJ45, OPS Slot, SD Card Slot:, Outputs - HDMI2.0, S/PDIF, Audio, RJ45 Control, USB-Touchport, RS232 : Std VESA Mounting, 600x400, Multiple OSD Languages: Certifications: BIS, CE, CB, FCC, ISO 14001 and 9001, Energy, Star 8.0, ROHS, TUV Low blue Light, TUV Flikerfree (Mandatory): Wifi Dongle Inclusive (AZ932-, HNG) complete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work. Approveed make: Benq/ Optoma/LG |
| 64 | SITC of OPS( on board PC) along with wi-fi, wireless mouse and keyboard, i5 11th generation, 8GB RAM,256GB SSD, Windows 11) complete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work. |
| 65 | SITC of wall mounting bracket for 86` Interactive display complete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work. |
| 66 | SITC of Min 6.5` (6.5` LF plus 1` HF) two-way coaxial thin edge ceiling loudspeaker, 100V transformer power taps : 24/12/6 W watts, Conical dispersion : 150° or more, impedance : 8, low impedance RMS continous power : 30 watts or more, frequency response ( plus /- 3dB): 55 Hz - 20 KHz or better, Max SPL(W/m) : 103 dB or better, Sensitivity: 88 dB or better etc. complete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work.CE Certification or more Approved Make: Matin Audio/ Audac/ QSC |
| 67 | SITC of Dual Channel power amplifier, RMS/AES power handling @ 4 ? : 2 x 250 W, @ 8 Ohms : 2 x 130 W, @ 8 Ohm Bridge : 1 x 500 W, Frequency response: 20 Hz - 20 kHz, Signal / Noise: ) 90 dB, THD plus N (@ 1 kHz): ( 0.1%, Crosstalk (@ 1 kHz): ) 70 dB, Technology: Class-D, Inputs sensitivity: 0 dB (1V RMS), Protection: DC Short circuit: Over heating: Over load: Signal limiting: Convection cooled, should be energy star rated, etc.complete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work, CE Certification or more Approved Make: Matin Audio/ Audac/ QSC |
| 68 | SITC of 4K UHD plus 4×2 HDMI Matrix with Audio Output provides the ability to connect up to four 4K UHD plus HDMI sources to up to two 4K UHD plus HDMI displays and freely switch between them. This unit comes with full support for 4K@60Hz (4:4:4, 8- bit) signals as well as support for 16-bit Deep Color, HDR (High Dynamic Range), 3D content, HD audio and other features defined by the HDMI 2.0 specification. A high-quality local analog stereo audio breakout from a selected HDMI output is also available. Each input’s EDID can be independently set to use either an internal (1080p@60Hz) or external (sink-copied) EDID. This unit also provides per-output auto source switching as well as connected display power control using CEC or RS-232 commands Approved Make: Extron/Crestron/Cypress |
| 69 | ITC of 4K HDMI extender kit (Transmitter and Receiver). Transmitter should have 1x HDMI and 1x RS-232 input port. 1x HDBaseT (RJ-45) and1x IR Blaster (3.5mm) output port. Maximum Input HDMI 4096×2160p@60 YUV 4:2:0 and Maximum Output HDBaseT 4096×2160p@60 YUV 4:2:0. Receiver should have 1x HDMI and 1x RS-232 output port. 1x HDBaseT (RJ-45) and1x IR Receiver (3.5mm) input port. Maximum Input HDMI 4096×2160p@60 YUV 4:2:0 and Maximum Output HDBaseT 4096×2160p@60 YUV 4:2:0. Both Tx and Rx should be HDMI 2.0 and HDCP 2.2 compliant. Extension length 40m at 4K and 70m at fullHD. Should support CEC bypass and should support pass-through audio formats including LPCM (up to 8 channels), Bitstream, and HD Bitstream and Deep Color input and output up to 12-bit.complete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work Product should be CE and FCC Certified.Approved Make: Extron/Crestron/Cypress |
| 70 | SITC of Cable Cuby with 1No LAN,2NosPower Socket, 1No HDMIcomplete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work |
| 71 | SITC of 12U quipment Rack with PDU FAN, Front glassdoor Lockable complete with all labour and petty material required to complete the job upto entire satisfaction of EIC of work |
| 72 | SITC od 2 core speeaker cable 16AWG complete with all labour and petty material required to complete the job upto entire staisfaction of E-I-C of work. |
| 73 | SITC of inter device connecting cable and connectors complete with all labour and petty material required to complete the job upto entire staisfaction of E-I-C of work. |
| 74 | Providing and fixing of PVC Modular Box of 6 Module ( 8`x3`) with outer face plate for mounting on surface complete with all labour and petty material required to complete the job upto entire satisfaction of E-I-C of work |
| 75 | Supply, Testing and Commissioning of wall fan 16` sweep (400mm) Oscillating type ( 70-90 )with 1300-2100 RPM speeds, 3-speed settings, and wide oscillation., Power consuming50- 60 watt, Air delivery 60-105 CMM, suitable for operation on AC 230V,50 hz supply i/c erection charges with petty material required to complete the job with required material and making necessary connection etc. Please Enable Macros to View BoQ information |
