Tender For Infrastructure Development Of Ranipur Jharial At Bangomunda Block, Bolangir (Part-1), Ranipur-Odisha

TDR : 55923727

Tender Notice
BOQ

13 Days Left

Ranipur , Odisha

Tender Brief : Tender For Infrastructure Development Of Ranipur Jharial At Bangomunda Block, Bolangir (Part-1)

Document Fees
₹ 10000 /-

EMD
₹ 1850400.0 /-

Tender Value
₹ 18.50 Crore /-

Submission Date
25-06-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	EARTHWORK EXCAVATION :- Earth work in excavation by mechanical means (Hydraulic excavator) in foundation trenches or drains, including dressing of sides and ramming of bottoms and dewatering wherever required, including all lifts, including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 5km including cost of all labours/ equipments, sundries and T&P etc all complete as per the direction of Engineer-in-charge.
2	Earth work in slushy soil with initial lead and lift including rough dressing in layers not exceeding 0.3m in depth and the Earth transported by transport vehicles as directed by the Engineer-in-charge.
3	Excavation of foundation in hard rock (Granite) removed by chiselling including dressing and levelling the bed not exceeding 1.5m in depth and depositing the soil within initial lead of 50m and as per the specification approved by the department.
4	Filling with available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering etc. including all lead and lift, cost of labour ,material, conveyance and taxes ,sundries ,T & P, complete as per the directions of Engineer-in-charge.
5	Filling in foundation, trenches and plinth with river sand, well watered and compacted in layers of with top surface dressed and leveled to proper gradient including cost of all materials, conveyance, all and royalties, loading and unloading, including cost of all labour, sundries ,T & P etc. complete as per directions of the Engineer -in-charge.
6	Disposal of building rubbish / malba /rock/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved dumping site or as approved /directed by Engineer-in-charge, including all lead and lifts involved, labour, etc. including all taxes as per the direction of Engineer-in-charge.
7	Providing, Supplying & Dewatering of the pond by using 5/10HP Diesel engine to drainage the water for exacavation etc. complete with all leads & lifts including cost of all labour,T&P completed as directed by the Engineer-In-charge.
8	Carriage of earth from site by mechanical means with cost of all lead & lift upto 5 km including cost of all labour, T&P etc., complete as direction of the Engineer-In-charge.
9	Clearing Grass and Removal of Rubbish up to a distance of 50 metres outside the periphery of the area.
10	Providing and laying WEDELIA GRASS with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.
11	Providing and laying CANNA INDICA of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.
12	Providing and laying ELEPHANT EAR of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.
13	Providing and laying VERTIVER GRASS of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.
14	Providing and laying plain cement concrete 1:4:8 (1 cement: 4 sand: 8 stone aggregate 40mm nominal size) as levelling course in foundation and plinth etc. including tempering, curing, shuttering etc. complete at all depth and height.
15	Providing and laying of Cement Concrete of grade 1: 3 :6 (1cement : 3 sand : 6 graded stone aggregate of size 25mm to 40 mm hard granite crusher broken metal ) ,mixing in concrete mixer ,lowering and compacting in proper thickness , watering & curing for the required period, including all cost of labour ,material, conveyance,royalties and sundries , T&P etc. complete as per the direction of Engineer-in-charge.
16	Providing & applying of pre constructional anti-termite treatment Confirming to IS 6313 (Part-II) and creating chemical barrier under and around the column pits, wall trenches, basement excavation top surface of plinth filling, junction of wall and floors along with external perimeters of building, expansion joints, surrounding the pipes and conducts etc. at the rate at 7,5 liter per sqm on vertical surface and 5.0 liter per sqm on horizontal surface. Chemicals:- Imidachloprid 30.5 SC , Doses: - 2.1 ml per lit of water cost of all materials, labour, conveyance, T&P , all taxes and hire charges of machinaries as per direction. Treatment at Junction of the inner wall and the floor ,Treatment of Top Surface of Plinth Filling , External Perimeter of building. (Make :- HI-Solution or Smart Care )
17	Providing ,Lifting, Hoisting & Laying Reinforced Cement Concrete of M-25 Grade in all type of Concrete works as per IS Specification, including cost of required steel centering and shuttering there after dismantling and removing the debrises away from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading,stacking, royalties of all materials, cost of all labours, scaffolding, sundries, T&P required for the work etc. complete in all respect but excluding cost of Reinforcement and Binding wires etc.
18	Footing
19	Column
20	plinth Beam
21	Roof Beam
22	Roof Slab
23	Lintel
24	Staircase
25	Flat slab
26	Supplying Cutting, straightening coiled or bent up M.S. Rod or tor steel of primary steel producers such as SAIL / Tiscon / RINL / JINDAL STEEL / SHYAM STEEL/ Rungta Steel/ Reliable Sponge/ Scan Steel/ SMC Power Generation/Shyam Metalics & Energy (grade Fe-500D) etc. including bending, binding, welding and jointing if necessary and tying the grills and placing in position as required for R.C.C. Work and for providing fan hooks as required, hoisting, lowering, laying including cost, conveyances of M.S. Rod or tor steel and binding wires of 18 to 20 gauge and labour required for the work for bending, binding and tying the grills in all floors with labour cess etc. (payment will be made on standard weight of B.I.S. for M.S. Rods or tor steel only) etc. complete as per specification & direction of Engineer-in-charge.
27	Fly Ash brick masonry in cement mortar 1:6: (1 cement: 6 sand) using Fly Ash bricks of 25cm x 12cm x 8cm having crushing strength not less than 75kg per sq. cm with dimensional tolerance +/- 2% including watering, curing and cost, y of all materials conveyance, royalty of complete. In Foundation andPlinth
28	Providing Fly ash bricks masonry work using (250mmx120mmx80mm size) having crushing strength not less than 75Kg/Sqcm in cement mortar (1:4). Immersing the bricks in water before use in all necessary projection splays cutting, circular moulding, corbelling etc. Including cost of conveyance ,taxes & royalties, loading and unloading of all materials & cost of all labour, scaffolding ,watering & curing ,sundries, T & P etc. complete as per the direction of Engineer-in-charge .
29	Brick masonry work using Exposed Wire cut brick of size( 250x125x80) mm strength not less than 75kg/sqcm in cement mortar (1:3) as per the direction of Engineer in charge.
30	FREE STANDING CURVE WALL
31	12MM THICK CEMENT PLASTER (1:6) :- Providing 12mm thick cement plaster to the surface of brick masonry wall with cement mortar (1:6) with mixing of water proofing compound etc. including racking out joints, scraping and cleaning the surface and finishing the plaster surface smooth using wooden floats only to proper plumbs and level and making grooves and beads to give required ornamental finish as per drawings including cost of all materials, conveyance, loading and unloading, all and royalties, all labour, scaffolding, watering and curing, sundries and T&P etc all complete as per direction of the Engineer -in-charge.
32	16MM THICK CEMENT PLASTER (1:6) :- Providing 16mm thick cement plaster to the surface of brick masonry wall with cement mortar (1:6) with mixing of water proofing compound etc. including racking out joints, scraping and cleaning the surface and finishing the plaster surface smooth using wooden floats only to proper plumbs and level and making grooves and beads to give required ornamental finish as per drawings including cost of all materials, conveyance, loading and unloading, all taxes and royalties, all labour, scaffolding, watering and curing, sundries and T&P etc all complete as per direction of the Engineer -in-charge.
33	6MM THICK CEMENT PLASTER (1:4) :- Providing 6mm thick cement plaster with cement mortar of (1:4) with mixing of water proofing compound to RCC surface of roof slabs ceilings , stairs, landings, chajja, shelves, columns, beams and lofts etc. including roughening, scraping and cleaning and finishing the plastered surface smooth using wooden floats only to proper plumbs and level, making grooves and beads to give required ornamental finish as per drawings including cost of all materials, conveyance, loading and unloading, all and royalties, all labour, scaffolding, watering and curing , sundries and T&P etc all complete as per direction of the Engineer -in-charge.
34	Providing and laying cement concrete 1:2:4 on walls (any thickness), including the cost of centering,shuttering and finishing :including cost of all materials, conveyance, loading and unloading, all taxes and royalties, all labour, scaffolding, watering and curing, sundries and T&P etc. complete as per direction of the Engineer -in-charge
35	Supplying, Fitting and Fixing Industrial Parking Vitrified Floor Tile of 10mm thick (SIZE 300X 300MM) on parking of approved shade laid on 25 mm thick cement mortar (1:1) and filling joints with epoxy grout (2mm) of approved quality including cost of all materials, labour T and P etc required for the works all complete. (For new work only) [NSWI]. Tile make:- NITCO/RAK/VARMORA, Epoxy Grout make:- ASIAN PAINTS (code9660)/ BERGER (HS Tile grout)/DULUX (epoxy grout).
36	Providing and laying Kota Stone Flooring using Kota tiles of area above 0.10 sqm of approved make, quality and colour without any warpage laid over an under layer of 20 mm thick base of cement mortar (1:4) (1 cement: 4 coarse sand) including cutting to size, laying and filling the joints with white cement slurry mixed with colouring pigment to match the shade and colour, cleaning the surfaces with oxlaic acid, machine grinding, mirror polishing including the cost of all materials, cost of all labour, conveyance,royalties, loading, unloading, sundries, watering and curing, T&P, etc. complete as per the direction of the Engineer-in-Charge. (Note- Sample of tile
37	Providing and laying Kota Stone in Dado/Skirting using kota tiles of area above 0.10 sqm of approved make, quality and colour without any warpage laid over an under layer of 12 mm thick base of cement mortar (1:3) (1 cement: 3 coarse sand) including cutting to size, laying and filling the joints with white cement slurry mixed with colouring pigment to match the shade and colour, cleaning the surfaces with oxlaic acid, machine grinding, mirror polishing including the cost of all materials, cost of all labour, conveyance, royalties, loading, unloading, sundries, watering and curing, T&P, etc. complete as per the direction of the Engineer-in-Charge. (Note- Sample of tiles shall be approved before procurement and use.
38	Providing & laying best quality Antiskid Ceramic floor tile of specified size of thickness 8-10mm of approved make confirming to IS-15622 specifications in floor over 20mm thick cement mortar (1:4) to proper slope, line and level including cutting to required size and shape, fixing at corners and splays etc. Including finishing the joints with epoxy based water proofing grout to match the color and shade of tiles complete as per the design & drawing with cost of all materials, labour, conveyance T&P etc. All complete as per the direction of Engineer -in-charge.
39	CERAMIC GLAZED WALL TILE FOR TOILET:- Providing and fixing ceramic glazed wall tiles of specified size of thickness 6-10mm conforming to IS: 15622 specifications of approved make and shade, in skirting and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and finishing the joint with epoxy based water proofing grout to match the shade. All complete as per the direction of Engineer-in-charge (Toilet) (Note- Sample of tiles shall be approved before procurement and use)
40	Providing and fixing ISI Marked 35mm thick flush door shutters confirming to IS:2202(Part-1) decorative type, core of block board construction with frame of 1st class hard wood and well teak three ply veneering with vertical grains or cross bands and face veneers on both faces of shutters of approved design including cost of all door fittings, and fixtures etc. complete.
41	Supplying, fitting and fixing of UPVC openable door with door frames of approved make with 6mm thick glass of approved quality complete with frame,fitting and fixtures etc.
42	Supplying,fitting,fixing of two track,two panel upvc sliding window of approve make with 6mm thick glass of approved quality complete with frame,fitting and fixtures etc.
43	WPC DOOR FRAMES :- Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge.
44	WPC DOOR :- Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water /moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge.
45	M.S GRILLS FOR WINDOW :- Supplying, Fitting and Fixing M.S Grills of approved designs made out of M S Flat, Square bars/Round bars etc. of approved specifications / dimensions with necessary welded clamps fixed in proper position & plumb including a single coat of priming of approved quality metallic primer, making required holes in Masonary Walls / R.C.C Structures (where necessary) and grouting the clamps with C.C(1:2:4) with 12mm size black hard crusher broken granite stone chips, making good to the damages of Masonary Walls / R.C.C Structures including cost, conveyance, loading, unloading, stacking, of all materials , cost of all labours, staging, scaffolding, sundries, T&P etc. complete as per the direction of the Engineer-in-charge.
46	Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of crosssection 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.
47	Supplying, fitting and fixing of UPVC openable door with door frames of approved make with 6mm thick glass of approved quality complete with frame,fitting and fixtures etc.
48	Supplying, fitting and fixing of stainless steel of 304 grade in hand rail using 50mm dia of 2mm thick circular pipe with balustrade of size 32mm x 32mm x 2mm @ 0.90 mt c/c and stainless square pipe bacing of size 32mm x 32mm x 2mm in three rows in staircase as per approved design and specification, buffing, polishing etc with cost, conveyance,of all materials, labour T&P etc. required for the complete in all respect as per the direction of Engineer -in- charge.
49	SYNTHETIC ENAMEL PAINT :- Painting with synthetic enamel paint of approved brand and manufacturer of required colour to give an even finish with two or more coats on new work of wood /steel over a coat of suitable shade with primer of approved brand and manufacturer's instructions including cost of all materials with taxes and transportation, all labour, scaffolding, sundries, T&P etc. All complete as per the direction of the Engineer -in-charge.
50	Providing and applying 2 coats of Plastic Emulsion Paint of approved quality and shade over Putty & wall primer of approved quality to surfaces (interior) including throughly brushing the surface free from foreign materials, sand papering smooth the intermediate coats,including of all materials, labour, conveyance, royalties, scaffolding, watering, curing, sundries, tools and plants etc as per the direction of Engineer-in-charge. (colour & shade to be approved before procurment & use)
51	Painting two coats with Water soluble weather coat paints of approved shade of approved make or equivalent over out side brick wall over a coat of primer, by means of brush to outside surface of new walls after scraping, cleaning the surface including all cost of materials, labour, all taxes, watering & curing T&P etc complete as per direction of Engineer -in-charge.
52	Providing one coat of Textured finish of approved make,quality and shade over the wall surface of the building over primer of approved make including cost of materials, all labour loading ,unloading scaffolding ,T & P etc as required for the work as per the direction of the Engineer-in-charge.( colour & shade to be approved before procurment & use)
53	Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Covers on drains of footpath of various sizes, of M-25 grade cement concrete, including cost of centering, shuttering, reinforcement of specified dia TMT bars of Fe 500 grade, neat cement punning on finished surface, properly encased on all edges and providing 2 Nos. 12 mm dia bar for hooks, including cost of all labours, materials, conveyance, loading and unloading, all taxes and royalties, sundries and T&P etc all complete as per direction of the Engineer -in-charge.
54	Random rubble H.G. stone masonry in cement mortar (1:4) in foundation and plinth.
55	Foundation & Plinth
56	Super Structure
57	Dismentalling of bitumen from the surface, scarcifing of bitumen
58	Waterproofing compound for Plastering: Additional for integral waterproofing compound Conplast WLXtra admixed at dosage of 200ml/bag of cement to mortar.
59	Repair of Plaster crack: Groove cut the existing crack by swa cut / chiselled a \\"V\\" groove 6mmX6mm on plastered surface and remove all dust and loose particles, fill the cracks with Renderoc CF having compressive strength 18 MPA @ 7days & 20MPa @ 20days (ASTM C109), Mix proportions by volume 1 part water: 3 parts of powder, Fresh Wet Density 1.95 gm/cc into the groove. Item rate is inclusive of materials all labour, tools and tackles, and transportation etc. complete as per specification and as directed by Engg.-in-charge.
60	Application of waterproof coating to Masonry Wall: Providing and Applying two (02) coats of high performance two component elastomeric cementitious dampproof coating system Nitoproof Damp Protect to the masonry wall surface. For best results damp the surface before coating with Nitoproof Damp Protect. After application of first coat to masonry surface, the second coat must be applied in perpendicular direction to the first coat when it has dried (approximately 4-6 hours at 20°C) Nitoproof Damp Protect conforms to the requirements of: • Mixed density :1.7 g/cc • Elongation at break as per ASTM D412: 100% • Crack bridging as per ASTM C1305 : No cracking up to 1.2 mm • Rapid Chloride penetrability resistance as per ASTM C1202: Very Low Coverage: One 15kg pack covers approximately 12m2 at about 1.0mm thickness depending on surface conditions and water usage. Item rate is inclusive of materials all labour, tools and tackles, and transportation etc. complete as per specification and as directed by Engg.-in-charge. Payment shall be made as per actual site measurement.
61	Exterior Waterproof cum anticarbonation Coating: The cleaning and preparation of the substrate to which elastomeric and decorative coating is applied must be carried out thoroughly to leave a sound base for the application. Any laitance present on the surface must be removed mechanically. Surface shall be maintained in SSD condition before applying of coating. Priming Coat Providing and applying single coat of single component water based primer, Nitocote AW, to the external RCC/Masonry walls as priming coat as per manufacturers specification. Top Coat Providing and applying 2 coats of elastomeric and decorative acrylic waterproof coating, Nitocote Wallguard, to the external RCC/Masonry walls of approved colour as per manufacturers specification. The coating shall be UV resistance, breathable & flexible having minimum 100% elongation when applied at 110 micron DFT.
62	TOILET WATER PROOFING :- AquaArm UM Waterproofing application: - Providing and application of two component polymer modified flexible cementitious waterproofing coating at a thickness of 1.5 -2.5 mm The membrane should have Elongation equal or more than: 60% Crack Bridging ability: Up to 1 mmAdhesive strength: 1.0 N/mm² @ 28d Tensile elongation: 30% @ 20°C Shore A Hardness >85 (between 3 - 7 days) etc. as per direction of E.I.CThe item rate shall be including of all kinds of labour, tools & tackle, machineries, lead & lift, mathadi charges, curing, wastages, consumable, cleaning, shifting of debris outside the site premises, surface preparation etc. complete as per design, drawing & instructions of EIC.
63	PRESSURE GROUT: Providing Chemical injection treatment in the form of pressure grouting to the cold joint by injecting cement slurry mixed with grout admixture ArmGrout Additive @ 250 gms per bag of cement, in the required consistency through the pre fixed PVC nozzles in the 10mm dia holes, fixing of PVC nozzles with quick setting compound ReArm Fix 10S and final cutting the projected nozzles and sealing off the PVC nozzles after the injection operation is over with quick setting compound ReArm Fix 10S, nonshrink rapidsetting mortar compound, finishing, curing etc. as per manufacturers specification and as directed.
64	Supplying all labour,material and equipment for mechanically demolish the existing structure and cutting of trees etc. and disposal of unserviceable material away from the site as per the direction and instruction of Engineer-in-charge. The cost inclusive all demolish of RCC structure including cutting reinforcement bars ,brickmasonry wall, concrete work , steel work, sheet, ph pipe lines & fittings, Electrical wiring and fittings, gully chamber, Gully trap, inspection chamber, mahole and Drain etc all complete.
65	Taking out the Existing AC & outdoor unit & Reinstalling the same from different building in the campus /site as per the direction of Engineer-in-charge.
66	Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.
67	Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge
68	Taking out the Existing Fans, lights , switch from different building in the campus and store these materials away from the site as per the direction of Engineer-in-charge.
69	Dismantling steel work in built up sections in angles, tees, flats and channels including allgusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.
70	Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:
71	Dismantling and removing old tiled flooring including removing the base course and stacking the useful materials for reuse and removing the debris within all lead and lift including cost of all labour etc. complete in all respect as per the direction of Engineer-in-charge
72	Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete
73	Dismantling RCC roof/col/beam(1Cum) including stacking the useful materials for reuse and removing the debries within 50mtr
74	Providing TEXTURED POLYCARBONATE sheet with all itsaccessories etc complete as per the direction & instruction of the E.I.C. [N.S.W.1
75	Removing old cement plaster from walls , including raking out joints 12mm deep and removing the debris away from the site with all lead and lift including cost of the direction of Engineer-in-charge.
76	Dismantling and removing 2.5 cm thick grading concrete from roof slab, cleaning the surface, lowering and removing the debris away from the site within all lead and lift including cost of all labour etc. complete in all respect as per the direction of Engineer-in-charge
77	Dismantling and removing doors, windows and ventilators including removal of frame, hinges, fastening the stacking the same reuse and removing the debris away from the site. within all lead and lift including cost of all labour, etc., complete in all respect as per the direct of Engineer-in charge
78	Dismantling and removing old tiled cladding from wall including racking out joints 12mm deep stacking the useful materials for reuse and removing the debris within all lead and lift including cost of all labour etc. complete in all respect as per the direction of Engineer-in-charge
79	Black Metal Signage \\" 64th Yogini Temple Ranipur Jharial \\" both in English & Odia .
80	Supply and installation of Desktop computer monitor size 23.8\\" with core i7 processor 8 gb ram 1000gb SSD /window 11 professional with microsoft offce suite software,including wired optical mouse and wired keyboard with all accessories(Make-HP280 G9SFFI7 12700 WIN 11P 81512SSD3WIFI/DELL)
81	Barrier type:straight boom pole,barrier material:crs(cold rolled steel), rising speed& falling speed :35,dimension length:4m,boom pole beight:890mm,arm moving direction:leftward (DS-TMG4B0-LA(6M)/Righward(DS-TMG4B0)-RA(6M), input power supply:220 VAC 15%, Push Button: wired for opening/Closing Manually, Anti Falling Radar (Photocell) - 01 Pair, Single channel Loop detector-01 No. (Vehicle safety)(Make-staright boom pole(Hikvision(model-DS-TMG4B0-LA(6M) out DS TMG4B0-LA(6m)/Toshi(Make-Antifall rader-Hikvision(model-DS-TMG304)/Toshi), (Make-Trigger rader-Hikvision (model-DS-TMG034)/Toshi), Make-Controller(Hikvision(model-TMG080-3)/Toshi)
82	Photoelectric BeamSensor(mostly for indoor use) (Comes in pair) (S-PB) (SECUREYE
83	Long Distance UHF Reader with TCP/IP, 12dbi antenna optional with effect distance more than 15m, 865-868/902-928MHz frequency band(frequency customization optional), RF output power up to 30dhm(adjustable), FHSS or Fix Frequency transmission (SOU200C-RJ) (SECUREYE)
84	1 Door/2 Reader Ethernet Controller with Power Supply, Card Holder: 1000 Cards, Logs:60000 Records, Alarm Events:10000 Events, Communication:TCP/IP (S-IP1D2R, SECUREYE)
85	UHF windshield tag (SECUREYE)
86	Installation
87	Gfrc Planter Box of 1.2 mtr Dia .75 mtr Height Manufacturing, Providing & Installation of GFRC Planter Box of approve size and specification as per the direction of Engineer-in-charge.
88	OUTERCURVE: Manufacturing, Providing & Installation of GFRC (Glass Fiber Reinforced Concrete), Make Samudyam, with Pattern, design, and colour of approved make to be fixed on/between RCC /Block work Column or structural work with Dry Fixing method with appropriate SS Pipe & Cleats frame work, using fasteners, and necessary hardware etc. The element shall be made from '53 grade' Portland Cement make Birla/ 'JK Cement' or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass fibre make 'Owens Corning' or equivalent, Super plasticizers / Additives make by 'BASF' or equivalent, Polymers make 'BASF' or equivalent and U.V resistant Synthetic inorganic pigments shall be used for pigmentation make 'BAYFERROX (Germany)' or equivalent. The material casting shall take place in Synthetic Rubber / FRP Mould manufactured by Mould / Tool / Mould Grade Resin of Revex/ 'Reckli' or equivalent.
89	GFRC JALI (thickness of 25-30 mm & Border thickness of 50)
90	GFRC BALUSTER (SIZE OF 170*1300)
91	GFRC RAILING (SIZE OF 80*1000)
92	Supplying, Fitting and Fixing onamental Cast iron Gate of design and approved specifications / dimensions with necessary welded clamps fixed in proper position & plumb including a single coat of priming of approved quality metallic primer, making required holes in Massonary Walls / R.C.C Structures (where necessary) and grouting the clamps with C.C(1:2:4) with 12mm size black hard crusher broken granite stone chips, making good to the damages of Massonary Walls / R.C.C Structures including cost, conveyance, loading, unloading,stacking, royalties and taxes of all materials , cost of all labours, staging, scaffolding, sundries, T&P etc. complete as per the direction of the Engineer-in-charge.( Weight to be taken properly prior to fixing the grills in the works and payment to be made accordingly )
93	Supplying all labour,material and equipment for mechanically demolish the existing structure and cutting of trees etc. and disposal of unserviceable material away from the site as per the direction and instruction of Engineer-in-charge. The cost inclusive all demolish of RCC structure including cutting reinforcement bars ,brickmasonry wall, concrete work , steel work, sheet, ph pipe lines & fittings, Electrical wiring and fittings, gully chamber, Gully trap, inspection chamber, mahole and Drain etc all complete.
94	Taking out the Existing AC & outdoor unit & Reinstalling the same from different building in the campus /site as per the direction of Engineer-in-charge.
95	Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.
96	Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge
97	Taking out the Existing Fans, lights , switch from different building in the campus and store these materials away from the site as per the direction of Engineer-in-charge.
98	Dismantling steel work in built up sections in angles, tees, flats and channels including allgusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.
99	Providing and fixing Plain Khondalite Stone Works, clading or wall of required thickness in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. Including cost of all labour, materials, royalties, loading and unloading, conveyance, sundries, T & P etc. All complete as per drawing and direction of the Engineer -in-charge.
100	Providing and fixing Plain Khandolite Stone work, kerb wall of required thickness in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. Including cost of all labour, materials, royalties, loading and unloading, conveyance, sundries, T & P etc. All complete as per drawing and direction of the Engineer -in-charge.
101	Providing and fixing khandolite Stone work, in flooring, of required thickness and size including dressing, packing and grouting with an admixture of pigment matching the stone shade. Including cost of all labour, materials, royalties, loading and unloading, conveyance, sundries, T & P etc. All complete as per drawing and direction of the Engineer -in-charge.
102	Providing and fixing Ornamental khandolite Stone work, plain in copings, cornices, string courses and plinth courses, of required thickness in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. Including cost of all labour, materials, royalties, loading and unloading, conveyance, sundries, T & P etc. All complete as per drawing and direction of the Engineer -in-charge.
103	Providing and fixing Plain Khandolite Stone work, wall of required thickness in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. Including cost of all labour, materials, royalties, loading and unloading, conveyance, sundries, T & P etc. All complete as per drawing and direction of the Engineer -in-charge.
104	Providing and fixing Khandolte Stone work, plain in copings, cornices, string courses and plinth courses, of required thickness in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade. Including cost of all labour, materials, royalties, loading and unloading, conveyance, sundries, T & P etc. All complete as per drawing and direction of the Engineer -in-charge.
105	Manufacturing, Providing & Installation of GFRC CIRCULAR PLANTER & BASE FOR BENCH (Glass Fiber Reinforced Concrete), Make 'SAMUDYAM', with Pattern, design, and colour. The element shall be made from '53 grade' Portland Cement make Biria/ 'JK Cement' or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass fibre make 'Owens Corning or equivalent, Super plasticizers / Additives make by 'BASF or equivalent, Polymers make 'BASF' or equivalent and U.V resistant Synthetic inorganic pigments shall be used for pigmentation make BAYFERROX (Germany)' or equivalent. The material casting shall take place in Synthetic Rubber / FRP Mould manufactured by Mould / Tool / Mould Grade Resin of Revex/ Reckli' or equivalent.  PLANTER- 1220 MM (Dia) X 1060 MM (Height)  BASE- 2120 MM (Dia) X 450 MM (Height)  GFRP POLTRUDED SECTION- (80 X 34) MM
106	GFRC RAILING OTHER 3 SIDES:-Manufacturing, Providing & Installation of GFRC RAILING incorporating Jali & Baluster (Glass Fiber Reinforced Concrete), Make Samudyam with Pattern, design, and colour of approved make to be fixed on structural work with Dry Fixing method with appropriate SS Pipe & Cleats frame work, using fasteners, and necessary hardware etc. The element shall be made from '53 grade' Portland Cement make Birla/ 'JK Cement' or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass fibre make 'Owens Corning' or equivalent, Super plasticizers / Additives make by 'BASF' or equivalent, Polymers make 'BASF' or equivalent and U.V resistant Synthetic inorganic pigments shall be used for pigmentation make 'BAYFERROX (Germany)' or equivalent. The material casting shall take place in Synthetic Rubber / FRP Mould manufactured by Mould / Tool / Mould Grade Resin of Revex/ 'Reckli' or equivalent.• JALI : Size of 1925 x 1000 MM : 1 Nos• BALUSTER : Size of 122 x 1065 MM : 2 Nos• BALUSTER TOP : Size of 200 x 122 : 2 Nos• RAILING : Size of 76 x 1900 MM : 1 Nos
107	Cobble Stone Pathway Providing and fixing of concrete exterior paving tiles in 'Cobblestone' finish in approved shade in sizes of 152mm x 152mm. The thickness of the tiles should range between 20 to 22 mm, allowing variance of ± 5mm in accordance with IS: 1237-1980. The tiles should be made with M40 Grade concrete mix design having ’43’ grade Portland cement, reinforced with Alkali Resistant glass fiber and the pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments manufactured by ‘BAYFERROX (Germany)’ or equivalent with high vibration technology. The pigmentation should be homogeneous and in accordance with British standard BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticizers and integrated water proofers agents and others. The tiles should be produced with high vibratory technology and their concrete mix design compressive strength should be of M-40 grade@28days. The top surface of the tiles should be treated with acrylic lacquer resulting in top surface water absorption of less than 1% and water absorption of less than 8% by 24 hours immersion method. The beds where tiles are to be laid should be clean, debris free, wet and mopped. The tiles should be laid to 1:4:8 PCC Concreting with cement mortar of 20mm thickness made with (1:3) Cement : Coarse Sand, adequate grooves should be maintained between 8-10mm using spacers and pointing work to be done with 1:3 (Cement : Fine Sand) mix.
108	Providing, supplying, and fixing Monier concrete roof tiles, ensuring a durable and weather-resistant roofing system. The tiles shall be high-quality, made of Portland cement, fine sand, water, and UV-resistant pigments, available in profiles like Elabana, Plano, Perspective, and Double Roman. Each tile, approximately 420 mm x 330 mm in size and weighing 4-5 kg, shall be installed with proper batten spacing (320-345 mm), corrosion-resistant nails or clips, and Monier underlay for waterproofing. Ridge and hip tiles shall be secured using the Monier Dry Ridge System to ensure proper sealing. The installation must follow IS 13801 standards, with correct alignment and overlap for optimal drainage and durability. Payment shall be based on the completed and accepted roofing area measured per square meter
109	STRUCTURAL STEEL WORK :- Providing and fixing of Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying two coat of Enamel paint and two coat of primer etc. all complete.
110	Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/ m²
111	Fixing of Onduline Make (Onduvilla- Shaded Red) Accessories like Ridges, Valleys & Apron according to site designs with minimum 8 nos Speedy screws to the above Framework will ensure manufactures specifications and warranty certifications. Providing and fixing Onduline make Corrugated bitumen tile (Onduvilla- Shaded Red) of size 1070 mm x 400 mm and reinforced with cellulosic fibers and thermosettingresin, 3 mm thick with tolerance of +/-10% along with Ridges & Valleys. Density not to exceed 1050 KG/m3 .The roofing tiles shall be fixed to the structural GI/MS/steel frame work to correct line and level with overlap 10 cm, side overlap 1 corrugation, purlin thickness not exceeding 2mm and placed at c/c distance of 32 cm. Fixing with Onduline make Speedy screws nominal diameter 4.2mm and Corrosion category C2(acc. EN ISO 12944-6) minimum 6 screws per tile of matching tile color complete as per manufactures specifications and as per the direction of the Engineer in charge.
112	Supplying and fixing of precast kerb stone of size 600mm x 300mm x 150mm of M-30 grade of approved make ,design,colour and size made by Block making machine with proper compaction fixed in required pattern etc. complete in all respect conforming to IS 5758:1984
113	OTHER 3 SIDES:-Supplying and fixing of 80mm thick cement concrete interlocking paver block of M-40 grade of approved make,design,colour and size made by block making machine with proper compaction laid in required pattern etc. complete in all respect confirming to IRC SP63:2018
114	Construction of granular sub-base by providing Close graded Granular subbase Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (4th Revision).
115	Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, laying in uniform layers with paver in subbase/ base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per Clause 406 of MoSRT&H Specifications for Road & Bridge works (4th Revision).
116	Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water
117	Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete
118	Supplying and stacking sludge at site including royalty and carriage upto 5 km complete
119	Rough dressing the trenched ground including breaking clods.
120	Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.
121	Fine dressing of the ground.
122	Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).
123	Supplying and stacking at site dump manure from approved source, including carriage upto 1 km (manure measured in stacks will be reduced by 8% for payment).
124	(ii)Screened through sieve of I.S designation 16mm
125	Grassing with selection no.1 grass including watering and maintainance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for moving including supplying good earth,if needed (the grass & good earth shall be paid separately)
126	Supply & laying of Geo fabric sheet of 200GSM(Polypropylene) sheet for ponding as per required size and pattern & finishing complete all as per direction of Engineer-in-Charge.
127	Grassing with selection carpet lawn grass including watering and maintainance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for moving including supplying good earth
128	Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.
129	Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :
130	Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)
131	Supplying and fixing of sculpture of approve design and approve make made out of khandolite stone etc all complete including cost of labour, material, conveyance, loading and unloading etc all complete.
132	Supplying and fixing of Ornamental Khandolite stone benches of approve size and Specification complete set etc. including cost of all labour,material,loading and unloading,conveyance,T&P etc.all complete as per the direction of E-I-C.
133	Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge.Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm
134	Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm
135	Location based signage: The signage structure is a combination of wrought/cast iron pipe structure with sandstone base and iron brackets. Stainless Steel Panel flags with symbol and text digitally H1625-RS printed on micro prismatic retro reflective boards conforming to type XI DG3 (diamond grade) 4000 series. Text language: Odia and English. Text height: Odia 55-60 mm; English 55-60 mm as per drawings & direction of Engineer in charge.
136	Wayfinding signage: Mild steel panels (with/without wrought iron frame) screwed directly on wall. Text printed digitally H1625 -RS printed on micro prismatic retro reflective boards conforming to type XI DG3 (diamond grade) 4000 series. Text language: Odia and English. Text height: Odia 40-45 mm English 40 - 45 mm Century 30 -35 mm. Icon height: 155 -175 mm as per drawings & direction of Engineer in charge.
137	Story signage: DG3 digital printing series (super high efficiency reflective sheeting) with alphabets/ numerical/ pictorials digitally printed and laminated using 1170c laminate in matt finish. The base corresponds to a specific kind of pedestal i.e. Kani Pista, with three mouldings with 4:5:6 proportion. Concrete structure with text etched and painted on top. Sandstone cladding at the base text. Language: Odia and English. Text height: Heading - 10 mm Supporting text - 8 mm as per drawings & direction of engineer in charge.
138	Cultural marker: Providing and fixing 600 x 600 x 1800 mm (LXWXH) culture marker made of stone block with CNC etching and carving designs fixed over MS support structure made up of 150 X150 mm MS pipes with weather proof paint and primer fixed on the sub structure inclusive of all necessary hardwares to make structure stable as per site with complete base work and foundation and research, scriptwriting, proofreading and copywriting of all the content in 3 language (Oriya , Hindi & Englidh )with designing the and developing the infographics of all the graphical representation, illustration, theoraticaland textual content placement of provided content along with development of print ready files for the fabrication and production as/design/drawing with complete work as per site engineer incharge.
139	Providing and fixing 2000 x 2000 x 3000 mm (LXWXH) culture marker made of Stone block with CNC etching and carving designs fixed over RCC structure with fixed on the sub structure inclusive of all necessary hardwares to make structure stable as per site with complete base work and foundation and research, scriptwriting, proofreading and copywriting of all the content in 3 language (Oriya , Hindi & Englidh )with designing the and developing the infographics of all the graphical representation, illustration, theoraticaland textual content placement of provided content along with development of print ready files for the fabrication and production as/design/drawing with complete work as per site engineer incharge.
140	Providing & supplying ss signage of size 450mmx150 mm as per the approved shade and design Including all cost of labour , T & P etc as per the detail design & specifications approved by EIC
141	Supplying and fixing of 120 Litre of different colour FRP Wheel Dustbin (wet & dry) , WB120L, Dimension: 92x48x55 cm.etc including cost of all labour,material loading,unloading,taxes etc.all complete as per the direction of E-I-C.
142	Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor of ISI marked Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI/V-Guard with 20 mm dia HMS FRLS PVC conduit ISI marked Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal 6A modular type ( flame retradant type) switch ISI marked Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) and ceiling rose ISI marked of modular type G.I box with metallic cover plate (both side) ( flame retradant type) Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) of suitable size, modular box with 1.5 sq. Mm FRLS PVC insulated single core multistandard copper conductor as earth wire including all accessories and connection as per direction of Engineer -in -Charge. . All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials.
143	GROUP-A
144	GROUP-B
145	GROUP-C
146	Supplying ,fixing of 6A Plug on the same board in existing switch board with complete fitting by 01 no of 6A switch & socket (modular type)( ( flame retradant type)) & other required accessories of ISI marked as approved as per direction of Engg. -in -Charge. Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.
147	Supplying,fixing of 6A Plug on the separate board with complete fitting by 01 no of 6A switch & socket(modular type)( ( flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge..Make-Schneider(Zencelo)/legrand( Myrius ) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a period of 2 years against manufacturing defects against which ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.
148	Supplying,fixing of 1x16A Plug on the separate board with complete fitting by 01 no of 16A switch & socket(modular type)(( flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge.. Make-Schneider(Zencelo)/legrand( Myrius)/Panasonic (vision) (For equipement power)All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.
149	Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge. 2 nos single core 1.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor. In 20 mm dia non metallic heavy duty conduit (LDB to LSB/LIGHT CKT)(2X1.5+1X1.5)
150	Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge.2 nos single core 2.5 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit.(BDB to LSB/LIGHT CKT/5A PLUG/UPS POINT ) (2X2.5+1X1.5)
151	Receass wiring for circuit/submain wiring with the following mentioned size PVC FRLS insulated, copper conductor, single core cable Make- Finolex/Anchor/Polycab/HAVELLS/RR KABLE/KEI in recessed HMS FRLS PVC conduit of mentioned size Make-AKG/BEC/Precision/Norpak/Anchor/Kinjal as required as per direction of Engg.-in-Charge.2 nos single core 4 sq. mm copper wire for phase and neutral and 01 no of single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia non metallic heavy duty conduit .(PDB to PSB/ POWER POINT/AC POINT) (2X4+1X1.5)
152	Supplying and installation of AC Point having 16-20A DP MCB, C series with enclosure, Schneider/Siemens/Legrand/ABB c of suitable size as required as per direction of Engg.-in-Charge .All the Components should be warrantied for a replacement period of 1 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.
153	Supplying,fixing of 2 nos 6A Plug on the separate board with complete fitting by 02 no of 6A switch & socket(modular type)( (flame retradant type)) with suitable size modular box & cover( flame retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge..Make-Schneider(Zencelo)/legrand( Myrius) /Panasonic (vision) .(Maximum 02 nos point in one circuit).All the switches & sockets should be warrantied for a period of 2 years against manufacturing defects against which ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.
154	Supply and fixing CALL bell (Ding dong type) /Buzzer on the existing switch box/cover.Make- Havells/Anchor as required as per direction of Engg.-in-Charge.All the Components should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.
155	S/F of Bakelite angle holder/batten holder (make-Anchor/Havells or equievalant reputed make A catagory ISI marked as approved )of ISI marked conforming to IS-1258/1987 in place of ceiling rose as per direction of Engg.-in-Charge .All the Components should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials.
156	S/F of 5 step type Modular electronic Fan Regulator ISI Marked with all connection complete in all respect as per direction of Engineer in charge ( Make-Schneider(Zencelo)/legrand( Myrius)/Panasonic (vision)
157	Supplying, installation, of exhaust fan of heavy duty 300 mm sweep 1400 rpm with louvers (Make- Havells/Crompton/Usha/Orient/Bajaj ) of exhaust fan in the existing wall, including fixing & conntection as required as per direction of Engg.-in-Charge. Replacement Warranty will be 2 years.
158	Supply, Installation, Testing and Commissioning of Duct mounted Single skinned Circular Inline Centrifugal Fan for Toilet Ventilation with direct driven Backward-curved impellers.The Fan has external rotor motor suitable for 1~, 230V, 50 Hz power supply. MAKE - SYSTEMAIR/ GREENHECK/ ELTA/Airflow3000 CFM @ 15mm MMWG static pressure
159	Supply & Fixing of Air Distribution Duting fabricated with Class VI GI Sheet(180 GSM) Complete With Supports, dampers, guiding vanes, access doors, MS Angle, Fire inhibiting gaskets, Nuts, bolts and all oyher accessories in accordance with approved drawing and the Specification. (Make:- Jindal/ Sail/ Tata)22 gauge (0.80 mm thickness)
160	24 gauge (0.63 mm thickness)
161	Supply, Installation, Testing and Commissioning of bird screen made by stain less steel for fans
162	Supplying and fixing of Energy efficient surface /recess mounted square /round shape 18 W LED luminaire of dimension of consists of white powder coated , die-cast Alluminium housing with high quality frosted diffuser for glare-free uniform lighting distribution with wattage not more than 18 watt and lumen output of 1800 lumens, , CRI not less than 80,CCT of 6000 degree K,THD less than 10%, with electronic driver, internal surge protection of 3 KV , L70 B50: 50000 hrs and all other accessories suitable for operation on 220 V to 240 V supply as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj).The luminaire should be Replacement Warranty will be 2 years
163	SITC of energy efficient LED tube light fittings with decorative alluminium batten and LED tube light having power rating not more than 20 watt and lumen output not less than 2200 lumen complete with electronic driver and all other accessories with diffuser having 2 years warranty i/c connection etc as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj). The luminaire should be Replacement Warranty will be 2 years .
164	SITC of Sleek LED 10 watt mirror light fitting with extruded polycarbonate housing,High optically efficient diffuser,above wash basin complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required as per direction of Engg.-in-Charge. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj)The luminaire should be Replacement Warranty will be 2 years
165	Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as requiredas required as per direction of Engg.-in-Charge .(Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)of ISI mark as approved.
166	SITC of High-efficiency IP66 flame proof wellglass with pressure die-cast housing and glass lens in front designed to meet the stringent requirements of ensuring safety in hazardous locations classified as Zone 1 and Zone 2 with Gas Groups IIA and IIB.Built with advanced flameproof technology, this luminaire is engineered to operate safely in areas with potential exposure to flammable gases, vapors, or dust having power rating not more than 30 watt and lumen output not less than 3000 lumen complete with electronic driver and all other accessories with diffuser having 2 years warranty i/c connection etc as required as per direction of Engg.-in-Charge. (Make: Orient Electric/Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj). The luminaire should be Replacement Warranty will be 2 years .
167	SITC of indoor rated IP20 5mtr LED Strip, operating in an ambient temperature of 0⁰C to 45⁰C. Operating at 50Hz frequency, housing of Polymide double sided PCB. LEDs used in the product shall comply with IEC 62471 for Photo-biological safety. Luminaire should have 70lm/mtr and total 350lumen in maximum 25Watt for 5mtr role. The LED shall comply with L70 life of 35000 burning hours tested at maximum current. The LEDs used should be with CCT of 3000/4000/5700 K. LED Driver shall be external type, suitable to operate in input voltage range of 140V to 300V (nominal rated voltage – 240V) with 3KV internal surge protection, Power factor of minimum 0.9, driver efficacy of minimum 85% and total harmonic distortion (THD) of less than or equal to 20% should be integral to the luminaire. (Make: Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj).The luminaire should be Replacement Warranty will be 2 years
168	BDBS,DB,AC DB,FLOOR PANELS,MCBS
169	Supplying and fixing of following mentioned way, three pole/single pole and neutral, sheet steel,double door MCB distribution board, 415 volts/240 volts shall be as per IEC 61439-3,integrated door earthing system offering additional safety to the user,High quality polyurethane Gasket,the box and cover shall be fabricated to withstand IK09,the DB should be properly pre-treated with 7 tank process and duly powder coated, phosphatized with powder coated finish, on surface/recess, complete with terminal blocks,with suitable size FR PVC insulated copper conducter up to terminal blocks, tinned copper busbar, neutral busbar, earth bar, din bar. Make-LEGRAND-Ekinox3 DB/ Siemens-Betaguard/ Schneider- Acti 9/ABB Itus as per direction of Engg.-in-Charge. The Distribution boards should be Replacement Warranty will be 3 years
170	Supply and fixing of 8 way DD single pole and neutral sheet steel MCB distribution board 250V on surface/recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (but with out MCB/ RCCB/ Isolator).Warranty on DB is 3 years
171	Supplying and fixing 6- 32 amps rating, 240 volts, C series, Double poles MCB of Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 in the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 1 years .
172	Supplying and fixing 6 amps to 32 amps rating, 240 volts, C series, single poles MCB of Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 . the existing MCB DB complete with connections as per direction of Engg.-in-Charge. The MCB should be Replacement Warranty will be 1 years.
173	Supplying and fixing 40 amps rating, 240 volts, C series,10KA breaking capacity, Double poles MCB of Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200 in the existing MCB DB complete with connections as per direction of Engg.-in-Charge. .Warranty on MCB is 1 year.
174	Supplying and fixing 40 Amps rating,C series,10KA breaking capacity, 2P, 415 volts, RCCB 30mA . Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB FB 200 in the existing MCB DB complete with connections, testing and commissioning etc. as required as per direction of Engg.-in-Charge. . The RCCB should be Replacement Warranty will be 1 year
175	CABLING AND END TERMINATION MAIN AREA
176	Supplying of one number PVC insulated armoured and PVC sheathed XLPE property AL. conductor power cable of 1.1 KV grade Make- Finolex/Polycab/HAVELLS/RR KABLE/KEI/Gloster of following size cables as per direction of Engg.-in-Charge.
177	4core x 16 sq mm(LIGHTING PANEL)
178	3.5core x 120 sq mm (DG 2 RUNS)
179	3.5core x 95 sq mm (EV PANEL)
180	3.5core x 70 sq mm (100A SUB PANEL)
181	3.5core x 240 sq mm(MAIN PANEL 400A)
182	LAYING OF CABLE
183	Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge.
184	Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size exceeding 120 SQ. MM but not exceeding 400 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge.
185	Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM direct in ground in the EXISTING PIPE etc as required as per direction of Engg.-in -charge.
186	Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size exceeding 25 SQ. MM but not exceeding 400 SQ. MM direct in ground in the EXISTING PIPE etc as required as per direction of Engg.-in -charge.
187	Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM in open duct etc as required as per direction of Engg.-in -charge.
188	Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size exceeding 25 SQ. MM in open duct 400 SQ. MM direct in ground in the EXISTING PIPE etc as required as per direction of Engg.-in -charge.
189	Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM in surface with shaddle and screw etc as required as per direction of Engg.-in -charge.
190	Supplying and making end termination with 4 core x16 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge.
191	Supplying and making end termination with 3.5 core x95 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge.
192	Supplying and making end termination with 3.5 core x120 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge.
193	Supplying and making end termination with 3.5 core x70 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge.
194	Supplying and making end termination with 3.5 core x240 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge.
195	Providing,fixing and laying of following dia G.I. pipe (medium class) in ground complete with G.I fitting incl. trenching(75 mm depth)and refilling as per direction of Engg.-in-Charge.
196	50 mm dia
197	Supplying,laying of 3cx2.5 sq.mm copper flexible cable with insulated cover with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials(make-Finolex/Polycab/HAVELLS/RR KABLE/KEI/Gloster )
198	Supplying,laying of 3cx2.5 sq.mm AL armoured XLPE cable with insulated cover with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials(make-Finolex/Polycab/HAVELLS/RR KABLE/KEI/Gloster )
199	Supplying,laying of 3cx6 sq.mm AL. armoured XLPE cable with insulated cover with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials(make-Finolex/Polycab/HAVELLS/RR KABLE/KEI/Gloster )
200	Providing,fixing and laying of fallowing dia HDPE pipe (medium class) in ground complete with fitting incl. trenching(75 mm depth)and refilling as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials
201	50 mm dia
202	S/I/T&Commissioning of LT OUTDOOR floor mounted cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing. (FOR ALL MAIN CONNECTED LOAD)as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.3P+N Type 1+2 SPD 65 kA with 63A 4P MCB,10kA, Cseries shall be installed in the incomer. 50X10MM Separate Aluminium Earth bus bar should be installed.Provision of cable alley chamber is mandatory. All the feeders shall have ON/OFF/TRIP indication.In commer-1-01 number of 400A 4P Icu=100%Ics,25Ka MCCB with TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula In commer-2- 01 number of 250A 4P Icu=100%Ics,25Ka MCCB with TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula .Changeover- 01 no of 250A 4P onload changeover switch ( DG 01 NO)(Make-Legrand/Siemens/Schneider/ABB).Busbar-1&2 04 numbers of 500Amps Aluminium busbar with 1A/SQ.MM current carring capacity. busbar duly sleeved by color coated PVC sleeve & supported by suitable size DMC insulator. (for outgoing).Out going- 04 numbers of 125Amps 4P MCCB.Icu=100%Ics,25Ka TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula .Out going-8 numbers of 100-63Amps 4P MCCB.Icu=100%Ics,25Ka TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula .Outgoing- 4 nos. 32A 2P MCB, C series, 10 ka , Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200.(ii) 02 set of digital type multifunction meter with CT for voltage,current,frequency,PF,THD indication(iii) All the MCCB outgoing feeders shall have digital ammeter with CT of suitable class 1 rating.(Make-Legrand/Siemens/Schneider/ABB)
203	S/I/T&Commissioning of LT Indoor floor mounted cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing.as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.3P+N Type 2 SPD 40 kA with 63A 4P MCB,10kA, Cseries shall be installed in the incomer. 20X10MM Separate Aluminium Earth bus bar should be installed.Provision of cable alley chamber is mandatory.All the feeders shall have ON/OFF/TRIP indication.In commer-1-01 number of 100A 4P Icu=100%Ics,25Ka MCCB with TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula .Busbar-1&2 04 numbers of 200Amps Aluminium busbar with 1A/SQ.MM current carring capacity. busbar duly sleeved by color coated PVC sleeve & supported by suitable size DMC insulator. (for outgoing.Out going- 8 numbers of 40A 2P MCB10KA,C series ( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200). Out going- 2 numbers of 40A 4P MCB10KA,C series ( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200) . Out going- 2 numbers of 63A 4P MCB10KA,C series ( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200).nstrument- (i) 03 numbers phase indicating lamp with toggle switch & HRC fuse. ii) 01 set of digital type multifunction meter with CT for voltage,current,frequency,PF,THD indication
204	Supplying,installation,testing & commissioning Of Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required as per direction of Engg. in charge.
205	Supplying & laying of 6 swg GI WIRE at 0.5m below the ground as strip earth electrode including connection/termination with nut ,bolt ,spring washer etc as required(jointing shall be done by over laping and with 2 sets of brass nut ,bolt & spring washer spaced at 50mm . as required as per direction of Engg. in charge.
206	Supplying & laying of 25mm x 5 mm GI strip at 0.5m below the ground as strip earth electrode including connection/termination with nut ,bolt ,spring washer etc as required(jointing shall be done by over laping and with 2 sets of brass nut ,bolt & spring washer spaced at 50mm . as required as per direction of Engg. in charge.
207	S/F of Street light- 90W,120 lm/w efficacy ,IP PC Lens new generation energy saving & environmental friendly long life versatile pressure die-cast alluminium IP66, IK 08 roadway luminaire with high power LED as light source with acrylic cover (Make-Panasonic/LT/Havells /Philips/Wipro/Crompton/Bajaj) (5Years Warranty)
208	Supply of 8 mtr long hot dip Galvanized Octagonal pole manufactured from HT steel(with decorative single arm) as per BS EN 10025/IS 2062 having minimum yield strength of 350 N/ SQMM having top dia of 70 MM A/F and bottom dia of 155 MM A/F of 3 mm thick or more , base plate as per IS 2062 complete with 4 nos. En 8 grade foundation bolts to withstand basic wind speed of 180 KM/HR wind speed (As per structural calculation of pole manufacturer )or more (Make of poles: Utkarsh/Bajaj/RR Ispat/Vakarangee as per direction of Engg. in Charge.
209	Supply of 8 mtr long hot dip Galvanized Octagonal pole manufactured from HT steel(with decorative DOUBLE arm) as per BS EN 10025/IS 2062 having minimum yield strength of 350 N/ SQMM having top dia of 70 MM A/F and bottom dia of 155 MM A/F of 3 mm thick or more , base plate as per IS 2062 complete with 4 nos. En 8 grade foundation bolts to withstand basic wind speed of 180 KM/HR wind speed (As per structural calculation of pole manufacturer )or more (Make of poles: Utkarsh/Bajaj/RR Ispat/Vakarangee as per direction of Engg. in Charge.
210	Installation of pole by making the suitable size foundation by embeding the pole 1 mtr into the ground with necessary civil work and fixing the light on the pole equievalant make ISI marked as approved as per direction of Engg. in Charge.
211	Supply, Installation, Testing & Commissioning of of IP66 LED (50-60)w Post Top Fixture with Body made of Pressure Die Cast Aluminium Housing for Optimal thermal Conductivity. With UV Stabilized PC Compound Lens for Good Impact Resistance. High Efficiency Driver with necessary safety Protection against Short Circuit, Miswiring,Over Voltage and Surge Protection of upto 10kV ( 6kV Internal and 10kV External SPD of IP67). System Efficacy>100lpw. THD<10%.Submission of LM79,LM 80 report from State/central accredited NABL laboratory).CRI>=80, PF>.95. CCT - 5700/4000K.Impact Resistance IK07.Operating Voltage Between (140-270)V. Avg life of 50,000 Burning [email protected] the light fixture and the Driver Should be BIS Approved. Before final procurement, the final design shall be approved by the concerned client and Engineer-in-charge.The price inclussive of 3 meter long aesthetically designed decorative light pole with Cast Aluminium base and cast aluminium in middle of the Pole . Pole shall made up of Mild Steel Body and coated with zinc rich primer & pure polyester powder coating and finished with black & gold embellishment. The pole shall be suitable for fitting of 50-60W decorative Heritage Light . Dimension of light must be Ø400mm dia and 800mm height. Body size of the pole will Ø88mm dia. The Pole shall have base Plate Ø230x12mm thick with provision for founation bolt fittings. Pole is Compatible for 70mm size for cable entry & exist. Junction Box service door is made up cast aluminium of size 325 X 90mm and the control gear tray only is prewired with 2.5sq mm cable, 6A SP MCB and 4pole studd connector for loop-in loo-out arrangement. The lighting manufactor must have own NABL Approved lab to justify the lumen efficacy, IP-66 protection and other parameters as required by the Engineer-in- Charge.(Make: K -lite Pole KP-12011-300 + KL-5444 Luminaries / LT/panasonic/Havells /Philips/Wipro /Crompton/Bajaj).
212	Supply, Installation, Testing & Commissioning of of IP66 LED (50-60)w Post Top Fixture with Body made of Pressure Die Cast Aluminium Housing for Optimal thermal Conductivity. With UV Stabilized PC Compound Lens for Good Impact Resistance. High Efficiency Driver with necessary safety Protection against Short Circuit, Miswiring,Over Voltage and Surge Protection of upto 10kV ( 6kV Internal and 10kV External SPD of IP67). System Efficacy>100lpw. THD<10%.Submission of LM79,LM 80 report from State/central accredited NABL laboratory).CRI>=80, PF>.95. CCT - 5700/4000K.Impact Resistance IK07.Operating Voltage Between (140-270)V. Avg life of 50,000 Burning [email protected] the light fixture and the Driver Should be BIS Approved. Before final procurement, the final design shall be approved by the concerned client and Engineer-in-charge.Make-Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj/K-Lite.The price inclussive of of 4 meter long aesthetically designed decorative light pole with Cast Aluminium base and cast aluminium in middle of the Pole . Pole shall made up of Mild Steel Body and coated with zinc rich primer & pure polyester powder coating and finished with black & gold embellishment. The pole shall be suitable for fitting of 50-60W decorative Heritage Light . Dimension of light must be Ø400mm dia and 800mm height. Body size of the pole will Ø88mm dia. The Pole shall have base Plate Ø230x12mm thick with provision for founation bolt fittings. Pole is Compatible for 70mm size for cable entry & exist. Junction Box service door is made up cast aluminium of size 325 X 90mm and the control gear tray only is prewired with 2.5sq mm cable, 6A SP MCB and 4pole studd connector for loop-in loo-out arrangement. The lighting manufactor must have own NABL Approved lab to justify the lumen efficacy, IP-66 protection and other parameters as required by the Engineer-in- Charge.(Make: K -lite Pole KP-12011-400 + KL-5444 Luminaries/LT/panasonic/Havells /Philips/Wipro /Crompton/Bajaj).
213	Supplying, Erection, Fixing, connection & testing of 50W LED Heritage GATE Light, Dimension of light must be Ø400mm dia and 800mm height, IP 66, IK07, amb. temp -10 to 45 degree celcious, CT 3000-5700K,,50000 HRS, CRI 70, 120 Lm/W system efficacy,driver efficiency >/ 85%,dia case aliminium housing,Clear Acrylic diffuser of Make-K-LITE Model No - 25444/LT/panasonic/Havells /Philips/Wipro /Crompton/Bajaj as approved maintenance free having 2 years warranty G.I P ipe with braket including MCB box & including with foundation as per the Drawing for inspection as required & as per direction of Engg.-in-Charge.
214	Supply, Installation, Testing & Commissioning of of IP65 (16)w Bollard Fixture with Body made of Extruded Aluminium /Mild steel Pole & PDC Aluminium Housing for Optimal thermal Conductivity. With UV Stabilized Injection Moulded Diffuser for Soft and even light distribution. High Efficiency Driver with necessary safety Protection against Short Circuit, Miswiring,Over Voltage and Surge Protection of upto 10kV ( 4kV Internal and 10kV External SPD of IP67) THD<10%. CRI>70, PF>.95. CCT - 5700/4000/3000K.Impact Resistance IK05.Operating Voltage Between (100-275)V. Avg life of 50,000 Burning [email protected] the light fixture and the Driver Should be BIS Approved.Before final procurement, the final design shall be approved by the concerned client and Engineer-in-charge. Make-K-K -lite Bollard KL-25582/Philips/LT/PANASONIC/Havells/Bajaj/Crompton/Wipro
215	Supply, Installation, Testing and Commissioning of 18W LED Focus Light having CCT 3000K +/-355K as per ANSI , CRI>80, SDCM<3. The fixture housing must be Made of extruded Aluminium housingfor better thermal healing & Powder coated by Corrosion resistant Nano coating technology. Luminaire must have minimum Ingress protection of IP66. The fixture should be equiped with stabilized Injection moulded special PC diffused optics ensuring low glare. The luminaire must have Integral high efficiency electronic thermally isolated constant current IP66 driver with operating voltage range of 90-205V, power factor > 0.95, THD < 10%, with Inbuilt surge protection of : 3kV and upgraded with integrated External IP67 protected SPD of 10KA surge protection .Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-03/05/06/07, Surge : IEC 61000-4-5, EMC : EN 55015. CE Certified, ROHS compliant, BIS Certification for Luminaires & Drivers. The lighting manufactor must have own NABL Approved lab to justify the lumen efficacy, IP-66 protection and other parameters as required by the Engineer-in- Charge. Make: K -lite Nebula KL-22782/LT/Havells/panasonic/Philips/Wipro /Crompton/Bajaj).
216	Supply, Installation, Testing and Commissioning of 50W LED Focus Light having CCT 3000K +/-355K as per ANSI , CRI>80, SDCM<3. The fixture housing must be Made of extruded Aluminium housingfor better thermal healing & Powder coated by Corrosion resistant Nano coating technology. Luminaire must have minimum Ingress protection of IP66. The fixture should be equiped with stabilized Injection moulded special PC diffused optics ensuring low glare. The luminaire must have Integral high efficiency electronic thermally isolated constant current IP66 driver with operating voltage range of 90-205V, power factor > 0.95, THD < 10%, with Inbuilt surge protection of : 3kV and upgraded with integrated External IP67 protected SPD of 10KA surge protection .Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-03/05/06/07, Surge : IEC 61000-4-5, EMC : EN 55015. CE Certified, ROHS compliant, BIS Certification for Luminaires & Drivers. The lighting manufactor must have own NABL Approved lab to justify the lumen efficacy, IP-66 protection and other parameters as required by the Engineer-in- Charge. (Make: K -lite Navi KL-26805/LT/Havells/panasonic /Philips/Wipro /Crompton/Bajaj).
217	Supplying and laying of one number PVC insulated armoured and PVC sheathed XLPE AL. conductor power cable of 1.1 KV grade POLYCAB/FINOLEX/HAVELLS/KEI/RR Kabel/Gloster of following size cables as per direction of Engg.-in-Charge.Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials
218	4core x 16 sq mm (OFP TO IND. TIMER PANEL)
219	4 core x 4 sq mm (for small power/LIGHT TO POLE)
220	Laying of PVC Insulated PVC Seated /XLPE power cable of 1.1 kv grade size not exceeding 25 SQ. MM direct in ground in the trench in one horizental formation including excavation ,sand coushing protection covering and refilling the trench etc as required as per direction of Engg.-in -charge.
221	Supplying and making end termination with brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge.
222	Supplying and making end termination with 4 core x16 sq mm brass compression gland and aluminium lugs for following mentioned size cable.as per direction of Engg.-in-Charge.
223	Supplying,laying of 3cx2.5 sq.mm copper flexible cable with insulated cover of reputed make,ISI marked with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials. Make-POLYCAB/FINOLEX/HAVELLS/KEI/RR Kabel/Gloster
224	Providing,fixing and laying of fallowing dia HDPE pipe (medium class) in ground complete with fitting incl. trenching(75 mm depth)and refilling as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials
225	50 mm dia
226	S/I/T&Commissioning of LT OUT DOOR FLOOR mounted cubical type IP66 based panel made out by 2mm CRCA steel sheet duly derusted & pented by simens gray powder cote paint is designed as G.A drawing. (FOR USE) with 63A TPN MCB 01 NO,1 no. Astronomical digital timer, AUTO MANUAL(with start and stop push button) SELECTOR 63 A 3P contactor, OLR,RYB,ON,OFF trip indication, Type-II SPD 40ka ,,04 nos 10A 4P MCB,C,10KA as outgoing MCB( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200) as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period 1 years of acceptance of materials
227	Supply,installation,testing and commissioning of 12M high mast shaft in two sections suitable for 55 m/sec wind speed along with head frame, luminaires carriage suitable for 6 luminaires in symmetrical arrangement and other accessories manufactured in factory. ( Bottom 360mm / Top -150mm, 3mm thickness, 445PCD, diameter of base plate 520mm including supplying of raising lowering system comprising double drum winch, 6mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightning finial. (Wiring material from JB to individual luminaire & MCB in base compartment are not included and are a part of installation)along with foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template along with Construction of shallow foundation with M20 grade concrete for the highmast considering the safe soil bearing capacity at site as 10 T/sqmtr at 2 metre depth with all materials and labour.Erection of the high mast with the help of suitable tools and plants, wiring of luminaires with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor cores of 1.5 sq. mm, lugs, MCB and all labour . Provision of GI pipe earthing for High mast with 2.5 M long 40 mm dia GI Pipe including connection to High mast earth terminal with 25 x 3 mm GI flats with all materials and labour. (2nos per mast required) Approved colour after treatment along with provision of masonary pedestal duly finished with plaster and painting with GI pipe for cable entering as required.. (2nos per mast required) (Make:-Bajaj/ Utkarsh/ Vakrangee/RR ISPAT/Valmont
228	SITC of 250W Outdoor Flood LED lights with polycarbonate module lens provided with silicon gasket for efficient ingree protection with silicon potted driver, IP66, IK08 , bottom opening maintanance , LPW not less than 120.Input Voltage: 85-265V AC ,Body : pressure Die cast Aluminium housing designed to act as heat sink for proper heat dissipation, IP66, CRI greater than eual to 70, burning hours 50,000 hrs, pf greater than 0.95, THD less than 10% as per the Drawing for inspection as required Panasonic/LT/Havells /Philips/Wipro /Crompton/Bajaj as rerquired & as per direction of Engg.-in-Charge.The luminaire should be Replacement Warranty will be 2 years .
229	LED type single dome aviation obstruction light. (Make:-Bajaj/ Utkarsh/ Vakrangee/RR ISPAT
230	S/I/T&Commissioning of LT OUT DOOR FLOOR mounted cubical type IP66 based panel made out by 2mm CRCA steel sheet duly derusted & pented by simens gray powder cote paint is designed as G.A drawing. (FOR USE) with 63A TPN MCB 01 NO,1 no. Astronomical digital timer, AUTO MANUAL(with start and stop push button) SELECTOR 63 A 3P contactor, OLR,RYB,ON,OFF trip indication, Type-II SPD 40ka ,,04 nos 10A 4P MCB,C,10KA as outgoing MCB( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200) as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period 1 years of acceptance of materials
231	Solar light
232	Supply of Elegant look 60 W(>=190lm/W) AIO LED Solar Street lights having extruded alluminium housing, 180Wp or more (subjected to final panel backup calculation with dimming profile of 100% output for 2 hrs, 90% output for 1 hr, 60% output for 1 hr and 50% output for 8 hrs per day. The calculation is to approved by SE,Electrical Circle (R&B) and CE ,Buildings, Odisha, BBSR before final procurement of the product.) Mono Crystalline Panel/Laminates fixed on the top of the luminaire housing, maintenance free 12.8 volts 96 Ah or more (subjected to final battery calculation with dimming profile of 100% output for 2 hrs, 90% output for 1 hr, 60% output for 1 hr and 50% output for 8 hrs per day. The calculation is to approved by SE,Electrical Circle (R&B) and CE ,Buildings, Odisha, BBSR before final procurement of the product.) LiFePO4 battery(BIS certified) , BMS, MPPT charge controller, PIR sensor( when there will be no movement the lumens output will be 30% output).The solar panel and battery should be designed to provide 2 days (24 hrs ) back up . The luminaire is having IP 65 protection for critical components, IK 08 and having lumen output of >=11400 lumens as per LM 79 report third party/central/state govt accredited NABL lab to justify the lumen output & lumen efficacy . Lenses should be provided on the LED chip for better lighting dstribution to avoid glare on human eyes. Both the luminaire and Mono Crystalline Panel must be manufactured in India. The Solar lighting company must submit the third party central/state govt accredited NABL lab reports to justify the lumen efficacy,luminaire output , IK 08 and IP 65 protection.The Luminaire should be supplied along with adjustable type mounting bracket which can be fitted directly on the pole.The Solar lighting manufacturer must submit the declaration letter by mentioning that complete solar light and the solar panel are manufactured in India and warranty certificate on their company's letterhead by mentioning warranty period as 5 years and necessary aftersales Service will be provided through their tollfree base service network located within 100 KM from the project site. The Solar Street light manufacturer should have own NABL accredieted laborotory. The following test reports must be submitted and approved from SE,Electrical Circle (R&B) and CE ,Buildings, Odisha, BBSR for the technical acceptance of the products.1.LM 79 REPORT and LM 80 Report ( from third party/central/state govt accredited NABL lab of AIO solar light) , 2. IK 08 ( from third party/central/state govt accredited NABL lab of AIO solar light ) , 3. IP 65 (Report of third party/central/state govt accredited NABL lab of AIO solar light 4. EN50530 – MPPT Efficiency , 5. IEC61547 , 6. IEC61000-3-2 – EMC , 7. IEC 60598-2-3 ,8. IEC 62109-1, ( The necessary test reports of third party/central/state govt accredited NABL lab from sl no. 4 to sl no.8 must be submitted for any wattage of AIO solar light )Make-(Philips/Panasonict/Wipro/Crompton/Bajaj/Havells/LT ). NB: The cost includes 5 years CMC including repair/ Maintenance/ replacement of the product in case of any defect.
233	Supply of 8 mtr long hot dip Galvanized Octagonal pole manufactured from HT steel as per BS EN 10025/IS 2062 having minimum yield strength of 350 N/ SQMM having top dia of 70 MM A/F and bottom dia of 155 MM A/F of 4 mm thick or more , base plate as per IS 2062 complete with 4 nos. En 8 grade foundation bolts to withstand basic wind speed of 180 KM/HR wind speed (As per structural calculation of pole manufacturer )or more (Make of poles: Utkarsh/Bajaj/RR Ispat/Vakarangee as per direction of Engg. in Charge.
234	Installation of pole by making the suitable size foundation by embeding the pole 1 mtr into the ground with necessary civil work and fixing the light on the pole equievalant make ISI marked as approved as per direction of Engg. in Charge.
235	Installation of 60W AIO LED solar street light on 8 mtr octagonal pole.
236	Supply of 20 Watt outdoor Horn Speaker, IP65, Frequency Response : 150 Hz – 15 kHz, 4 INCH DRIVER, peak power handling capacity 80W, Should have Passive 350 Hz high-pass filter built-in, SPL : 133 dB peak @ 1.4 kHz, IP-65 rating per IEC529, Coverage Pattern: 60° horizontal by 80° vertical , Maximum SPL (1m): 109dB peak, 8 ohm Impedence, Transformer Taps: 70V/100V: 20W, 100V: 30 w.MAKE:Bose/EV/Audac(HS121)/Sonodyne
237	Supplying, installing, testing and commissioning of quad channel Power amplifier of continous power 4x 240 W @8 ohm and 100V, frequency response- 50Hz-20 kHz , class D amplifier.The amplifier should be clean reliable audio for public address amplification and music.Line input less than 1 volt, unbalanced& line output less than 1 volt unbalanced.Make-Bose/Audac(PMQ240)/EV/Sonodyne
238	Supply of 30 W weather proof rock speaker with LMT, IP65 , Transformer Taps: 70V/100V: 20W, 100V: 30 w Make-Sonodyne (RS 650)/Bose/EV/Audac
239	Supply of 10-Channel Mixing Console: Max. 4 Mic / 10 Line Inputs (2 mono + 1 stereo) / 4 GROUP Buses + 1 Stereo Bus / 4 AUX (incl. FX),16-Channel Mixing Console mic preamps with an inverted Darlington circuit,1-Knob compressors,High-grade effects: SPX with 24 programs,24-bit/192kHz 2in/2out USB Audio functions,Works with the iPad (2 or later) through the Apple iPad Camera Connection Kit / Lightning to USB Camera Adapter,Includes Cubase AI DAW software download version,PAD switch on mono inputs,+48V phantom power,XLR balanced outputs with provision for bluetooth.Make-Yamaha/Soundcraft/Studiomaster
240	SITC of 17U 600/650D UL Listed Floor mount Rack with Front perforated door with 3 point lock, Rear mesh door with Cam lock and 3inch Castor Wheel included with 2 no 6/16 Amp Indian-Standard - 06 Socket - Single Pole / Screw Mountable / 16 Amp MCB / Alternating Current - 16 Amp 3 Pin Plug with Power Cable 2.5 sq.mm 3 meter Length, 4nos 1U Metal Cable manager with Plastic cable loops, 2nos CFM FAN set, 1no Monitor Tray - Ventilation - 495W - 375D and H/W screw920sets). Make: Valrack/ Rittal/ Legrand
241	Speaker Cable Armoured 2 core 2.5 sqmm PVC Sheathed etc complete as required.
242	Laying of cable (Digging , laying and refilling with sand and Bricks)
243	Installation of all equipment, testing and commissioning of the system
244	EV CHARGE STATION
245	Supplying,fixing of 1x16A Plug on the separate board with complete fitting by 01 no of 16A switch & socket(modular type) with suitable size modular box & cover including supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge.. Make-Schneider(Zencelo)/legrand( Myrius)/Panasonic (vision) (For equipement power)All the switches & sockets should be warrantied for a replacement period of 2 years against defects with ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free aftersales service within warranty period for acceptance of materials. (For bike charging)
246	S/I/T&Commissioning of LT OUTDOOR floor mounted cubical type electrical main panel (for both light and power circuit) made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing.as per direction of Engg.-in-Charge. Warrentee period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.3P+N Type 2 SPD 40 kA with 63A 4P MCB,10kA, Cseries shall be installed in the incomer. 20X10MM Separate Aluminium Earth bus bar should be installed.Provision of cable alley chamber is mandatory.All the feeders shall have ON/OFF/TRIP indication.
247	In commer-1-01 number of 125A 4P Icu=100%Ics,25Ka MCCB with TMR based release ( Make-LEGRAND-DPX3 / Siemens-3VA Model/ Schneider- CVS/ABB Formula
248	Busbar-1&2 04 numbers of 200Amps Aluminium busbar with 1A/SQ.MM current carring capacity. busbar duly sleeved by color coated PVC sleeve & supported by suitable size DMC insulator. (for outgoing)
249	Out going- 16 numbers of 40A 2P MCB10KA,C series ( Make-LEGRAND-DX3/ Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200)
250	Instrument- (i) 03 numbers phase indicating lamp with toggle switch & HRC fuse.
251	(ii) 01 set of digital type multifunction meter with CT for voltage,current,frequency,PF,THD indication
252	Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S cylindrical body, squeeze lever dischange valve fitted with pressure indicating gauge internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to IS : 2878 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.Make- Safex/Supremex/ Ceasefire/Flameklog .4.5 kg capacity
253	Providing and fixing ABC type fire extinguishers consisting of welded M.S cylindrical body, squeeze lever dischange valve fitted with pressure indicating gauge internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to IS finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.Make- Safex/Supremex/ Ceasefire/Flameklog.6 kg capacity
254	Supplying and installing at approved location approved make fire buckets at 24 gauge galvanized stseel sheet, standard 9 liters capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letter \\"FIRE\\" in black and gold. Cost shall be inclusive of Providing MS stand duly painted over a coat of primer (one stand shall be suitable for hanging 5 buckets.
255	SIGNAGES: SITC flexyl of Photoluminescent based Glow-in-the-dark sheeting with luminious properties enclosed in a weather-proof UV stabilized film with UV screen printing by imported inks pasted over 3 mm Thick Cast Acrylic Sheet with the Protection of 3 mm Thick Cast Acrylic from Front side with stud type mirror screw with lifespan of 5 years, visible upto 4-6 hrs in total darkness for floor indication, fire exit, hydrant, hose reel, fire extinguisher, MCP, fire alarm panel, in case of fire, lift, alarm valve signages
256	Illumination Glow light for Exit Indication with Battery Back-up. Make-Prolite/Bajaj
257	Supply, Transportation, erection, testing and commissioning of 3 Phase, 415V, 50Hz, water cooled multi cylinder diesel generator set with alternator of 58.5KVA ( Make -Kirloskar / Jakson/TMTL/Mahindra/Captiva/Sterling) out put contineous rating directly coupled Engine and Alternator with guard and mounted on a common base plate of Robust construction and complete with AMF panel having IP-52 protection, Acoustic Enclosure as per CPCB IV+ norms , sound absorbing material, to restrict sound level up to 75 dB up to 1 mtr distance and as per CPCB IV+ norms etc as per following specifications mentioned below. Warrentee period must be 2 years ALTERNATOR:The alternator of the output rating shall be 3 Phase, 415V, 50Hz, Ac , 0.8 P.F. lagging at 1500 RPM. The alternator is self excited, self regulated, and shall confirm to IS: 13364 of 1992 with regulation of +5% from no load to full load. degree of protections shall be IP21.ENGINE: Diesel Engine start, developing suitable BHP output at 1500 RPM with mechanical / electronic governing so as to enable the alternator to give 58.5KVA continuous output at 0.8 P.F. lagging at NTP conditions. The diesel engine shall be capable of providing 10% O/L for 1 Hr for every 12 Hrs of continuous running at full load. The engine with 1st filling of oil and Diesel etc.01. Exhaust pipe of required size and length with insulation or clading.02. Diesel tank suitable for 8 to 10 Hours running capacity.03. Residential Silencer.04. SMF Batteries with leads as per the Manufacturer standardsAMF PANEL: Cubical, Compartmentalized, AMF Panel Baord with all Power & Control Contractors, Switches, Meters and other accessories, Internal Wiring, connection, inter-connection etc. for Trouble Free smooth function for 58.5 KVA DG Set complete with Battery Charger & leads as required. BASE PLATE: Common Base Plate of required size for mounting of Engine Alternator Set fabricated from MS Channel and vibration damping arrangement with cushy foor mounting including paintng etc. as required. FOUNDATION: Suitable size Cement Concrete (1:2:4) foundation duly plastered and finished with neat coat Cement as required along with smoke exhaust system piping including base frame of structure & lightening protection system. , control cable of 15mtr 2.5sqmm 6core , civil foundation work. (The Manufacturing of DG set shall not in any case be more than six months old from the date of award of work)
258	LIGHTENING PROTECTION SYSTEM--- Lightning Protection :- Supply of 8 mm Aluminum Round Conductor.Tested as per IEC 62561. as per direction of engineer in charge.Make-OBO/Dehn/ABB
259	Supply of Roof conductor holder for parapet- PolyamideConductor holder:With M8 female thread or diameter 7mm, M8Screw to connect the conductor holder.Weather andtemperature resistant from -35 to +90 degree Celsius tested.Conductor holder @ 1 meter distance.Tested as per IEC 62561. as per direction of engineer in charge.Make-OBO/Dehn/ABB
260	Supply of Polyamide roof cable holder for flat roof:DIN 48829 Form B1. Closed form with bottom. Filling weight1Kg (frost-resistant concrete). Sleeve from polyethylene, black@ 1 meter distance. Tested as per IEC 62561. Make-OBO/Dehn/ABB
261	Supply of Connector: For T cross and parallel connectors. Quickinstallation using hexagonal bolt M10X30 high-grade hot dipgalvanised. Tested as per IEC 62561.(2nos/expansion piece ).Make-OBO/Dehn/ABB
262	Supply of 1 mtr vertical air terminal with mounting accessorieson the flat surface to meet the requirements of IS/IEC 62305.Tested for Electrical , mechanical and chemical as per IEC62561. Tested for 100kA lightning current. Make-OBO/Dehn/ABB
263	Supply of Vertical air terminal with accessories:Providing of Air terminalsas per IS-IEC -62305 part-3Nominal size Ø10/16 mm aluminium rod:2 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN48801) Suitable for high wind load.Tested as per IEC 62561. Make-OBO/Dehn/ABB
264	Supply for Providing of Stand for Fang Fix system 16 kg with base andclamp ,made up of frost resistant concrete and clamp testedupto 100KA lightning current . Make-OBO/Dehn/ABB
265	Supply for Providing of Stand for Fang Fix system 16 kg made up of frostresistant concrete. Make-OBO/Dehn/ABB
266	Supply of Test Joint (Folding Clamp) suitable to connect 8mmround conductor and max by 30x3 mm GI strip as specified indrawing and directed by Engineer.Tested for 100kA lightning current. Make-OBO/Dehn/ABB
267	Supply of IP 66 Poly Propylene Junction Box. Installation at 1Mtr HeightFor Test Joint .Internal dimensions: 100x100x48 mm Make-OBO/Dehn/ABB
268	Supply of Galvanised Steel Flat 30X3 mm thickness from earthelectrode directly in ground as required. Flat conductor HotDipped Galvanized. Tested as per IEC 62561. Make-OBO/Dehn/ABB
269	Supply for Providing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate. Tested for 100kA lightning current. Make-OBO/Dehn/ABB
270	Supply of flat conductor holder- Fit: FL 30, With mounting hole6.2 x 22 mm, With 2 cylinder bolts M6 x 16 and over-piece fromhot-dip galvanised steel, Bottom section from polyamide, black.Tested as per IEC 62561. Make-OBO/Dehn/ABB
271	Supply for Providing of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric. Make-OBO/Dehn/ABB
272	Supply of UL Listed maintenance free ,Low carbon coppercoated earth rod of 3 metre electrode having diameter of 17.2mm with copper coating thickness of 250micron tested as perIEC 62561-2 Make-OBO/Dehn/ABB
273	Supply of universal clamp made of SS to connect rod with flatconductor Make-OBO/Dehn/ABB
274	Supply of Earth conductivity enhancing mineral compound shall be of 25kg/pit tested as per IEC 62561-7,TCLP tested Make-OBO/Dehn/ABB
275	Supply of The above arrangements shall be provided with Heavy dutyearth champer of 5000kg load bearing capacity to ensure thesafety of earthing system Make-OBO/Dehn/ABB
276	Installation of The above arrangements including all accessories as per Direction of Engg. In charge.
277	SITC of high quality long through multi colour with RGBW 4in1 LED, DMX-RDM based wash light, Protection Rating: IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598 (Part 2/Sec 1):2020\\", and \\"Electromagnetic Compatibility Directive - EN 61547:2020\\", Mounting Structure: Adjustable surface mount yoke arrangements for fixing the lights having the rotation degrees embossed in the die cast. Power consumption: 50W, CCT: RGBW (6000K -7000K) (as per the design approval), Optics: PMMA/PC Lens with separate holder, Beam Angle: 25°/45°/60°(as per the design approval), Luminous Efficacy must be Min : 55Lm/W, Body: Die casted/ extruded aluminium with embossed manufacturer logo, Separate compartment for keeping the decoder/driver in the housing which can be easily removable for service without disturbing the LEDs/Optics, Hot spot and light distribution: Optics Designed to minimize hot spots & fringing in colour mixing applications. Luminaire shall be capable of producing dynamic colour-changing light with 16.7million colours and it shall support control via DMX, Ethernet, and Remote Device Management (RDM) for enhanced configuration and management. The luminaire should offer channel options of 8/ 4 channels by using a Programming kit, with these channels providing control for effects and colour transitions like 4 colour 4 channels, Master, Jump, strobe, Macro function and speed in the rest 4 channels as per the requirement. Additionally, it shall feature auto colour synchronization functionality, allowing seamless operation if there is a loss of DMX signal/ with loop in loop out. Power Input: DC 24V External Group Driver, Surge Protection: Inbuilt surge protection in the driver 2KV-4KV (Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection: IK08 or higher, Painting: Chemical 3/7 tank processed treatment before the powder coat black/Grey/approved colour coat. Fixture will be suitable to operate in a temperature range of -10°C to +60°C, the light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 50 degrees centigrade LM80 to be provided. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35-micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK08, HV & IP66 Certificates from NABL Accredited laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with LM80 report from as international testing Laboratory. Power & DMX Loop In/Out along with moulded connector having the length >300mm. Certifications: CE, RoHS, BIS.Make-Leksa lighting/Canara lighting/LT/Philips
278	SITC of high quality long through multi colour with RGBW 4in1 LED, DMX-RDM based wash light, Protection Rating: IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598 (Part 2/Sec 1):2020\\", and \\"Electromagnetic Compatibility Directive - EN 61547:2020\\", Mounting Structure: Adjustable surface mount yoke arrangements for fixing the lights having the rotation degrees embossed in the die cast. Power consumption: 100W, CCT: RGBW (6000K -7000K) (as per the design approval), Optics: PMMA/PC Lens with separate holder, Beam Angle: 25°/45°/60°(as per the design approval), Luminous Efficacy must be Min : 55Lm/W, Body: Die casted/ extruded aluminium with embossed manufacturer logo, Separate compartment for keeping the decoder/driver in the housing which can be easily removable for service without disturbing the LEDs/Optics, Hot spot and light distribution: Optics Designed to minimize hot spots & fringing in colour mixing applications. Luminaire shall be capable of producing dynamic colour-changing light with 16.7million colours and it shall support control via DMX, Ethernet, and Remote Device Management (RDM) for enhanced configuration and management. The luminaire should offer channel options of 8/ 4 channels by using a Programming kit, with these channels providing control for effects and colour transitions like 4 colour 4 channels, Master, Jump, strobe, Macro function and speed in the rest 4 channels as per the requirement. Additionally, it shall feature auto colour synchronization functionality, allowing seamless operation if there is a loss of DMX signal/ with loop in loop out. Power Input: DC 24V External Group Driver, Surge Protection: Inbuilt surge protection in the driver 2KV-4KV (Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection: IK08 or higher, Painting: Chemical 3/7 tank processed treatment before the powder coat black/Grey/approved colour coat. Fixture will be suitable to operate in a temperature range of -10°C to +60°C, the light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 50 degrees centigrade LM80 to be provided. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35-micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK08, HV & IP66 Certificates from NABL Accredited laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with LM80 report from as international testing Laboratory. Power & DMX Loop In/Out along with moulded connector having the length >300mm. Certifications: CE, RoHS, BIS. Make-Leksa lighting/Canara lighting/LT/Philips
279	SITC of high quality Multi Color Neon Flexible light, Protection Rating : IP65, Mounting Structure : Adjustable wall mount aluminium profile for fixing the lights. Power consumption : 12W, CCT : RGB/RGBW, (as per the design approval) Beam Angle : 120º, Control : DmX512 Channel : 4 CH, Power Input : DC 24V with external driver, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life time should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. LED Makes should be CREE, LumilLED, Osram, Seoul, Epistar, Nichia or equivalent with the engineer or 3rd party testing laboratory approval.Make-Leksa lighting/Canara lighting/LT/Philips
280	SITC of Aluminium Profile for Neon flex
281	SITC of high quality long through multi colour with RGBW 4in1 LED, DMX-RDM based spot light, Protection Rating: IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598 (Part 2/Sec 1):2020\\", and \\"Electromagnetic Compatibility Directive - EN 61547:2020\\", Mounting Structure: Adjustable surface mount yoke arrangements in the die cast for fixing. Power consumption: 12W, CCT: RGBW (6000K - 7000K) (as per the design approval), Optics: PMMA/PC Lens with holder, Beam Angle: 25°/45°/60°(as per the design approval), Luminous Efficacy must be Min : 55Lm/W, Body: Die casted aluminium with embossed manufacturer logo, Separate compartment for keeping the decoder/driver in the housing which can be easily removable for service without disturbing the LEDs/Optics, Hot spot and light distribution: Optics Designed to minimize hot spots & fringing in colour mixing applications. Luminaire shall be capable of producing dynamic colour-changing light with 16.7million colours and it shall support control via DMX, Ethernet, and Remote Device Management (RDM) for enhanced configuration and management. The luminaire should offer channel options of 8/ 4 channels by using a Programming kit, with these channels providing control for effects and colour transitions like 4 colour 4 channels, Master, Jump/ strobe, Micro function and speed. Additionally, it shall feature auto colour synchronization functionality, allowing seamless operation if there is a loss of DMX signal/ with loop in loop out. Power Input: DC 24V External Group Driver, Surge Protection: Inbuilt surge protection in the driver 2KV-4KV (Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection: IK07 or higher, Painting: Chemical 3/7 tank processed treatment before the powder coat black/Grey/approved colour coat. Fixture will be suitable to operate in a temperature range of -10°C to +60°C, the light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 50 degrees centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35-micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, HV & IP66, Certificates from NABL Accredited laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with moulded connector having the length >300mm. Certifications: CE, RoHS, BIS. Make-Leksa lighting/Canara lighting/LT/Philips
282	SITC of high quality long through Multi colour with RGBW 4in1 LED, DMX-RDM based linear wash light, Protection Rating: IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598 (Part 2/Sec 1):2020\\", and \\"Electromagnetic Compatibility Directive - EN 61547:2020\\", Mounting Structure: Adjustable surface mount yoke arrangements in the die cast for fixing. Power consumption: 30W, CCT: RGBW (6000K - 7000K) (as per the design approval), Optics: PMMA/PC Lens with holder, Beam Angle: 25°/45°/60°(as per the design approval), Luminous Efficacy must be Min : 55Lm/W, Body: Die casted/ extruded aluminium with embossed manufacturer logo, Separate compartment for keeping the decoder/driver in the housing which can be easily removable for service without disturbing the LEDs/Optics, Hot spot and light distribution: Optics Designed to minimize hot spots & fringing in colour mixing applications. Luminaire shall be capable of producing dynamic colour-changing light with 16.7million colours and it shall support control via DMX, Ethernet, and Remote Device Management (RDM) for enhanced configuration and management. The luminaire should offer channel options of 8/ 4 channels by using a Programming kit, with these channels providing control for effects and colour transitions like 4 colour 4 channels, Master, Jump/ strobe, Micro function and speed. Additionally, it shall feature auto colour synchronization functionality, allowing seamless operation if there is a loss of DMX signal/ with loop in loop out. Power Input: DC 24V External Group Driver, Surge Protection: Inbuilt surge protection in the driver 2KV-4KV (Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection: IK07 or higher, Painting: Chemical 3/7 tank processed treatment before the powder coat black/Grey/approved colour coat. Fixture will be suitable to operate in a temperature range of -10°C to +60°C, the light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 50 degrees centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35-micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, HV & IP66 Certificates from NABL Accredited laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with moulded connector having the length >300mm. Certifications: CE, RoHS, BIS.Make-Leksa lighting/Canara lighting/LT/Philips
283	SITC of high quality long through Multi colour with RGBW 4in1 LED, DMX-RDM based linear wash light, Protection Rating: IP66, complying to BIS standard \\"IS 10322 (Part 5/Sec 1): 2012\\" and having CE certification against standard \\"Low Voltage Directive & Protective Equipment - EN 60598 (Part 2/Sec 1):2020\\", and \\"Electromagnetic Compatibility Directive - EN 61547:2020\\", Mounting Structure: Adjustable surface mount yoke arrangements in the die cast for fixing. Power consumption: 50W, CCT: RGBW (6000K - 7000K) (as per the design approval), Optics: PMMA/PC Lens with holder, Beam Angle: 25°/45°/60°(as per the design approval), Luminous Efficacy must be Min : 55Lm/W, Body: Die casted/ extruded aluminium with embossed manufacturer logo, Separate compartment for keeping the decoder/driver in the housing which can be easily removable for service without disturbing the LEDs/Optics, Hot spot and light distribution: Optics Designed to minimize hot spots & fringing in colour mixing applications. Luminaire shall be capable of producing dynamic colour-changing light with 16.7million colours and it shall support control via DMX, Ethernet, and Remote Device Management (RDM) for enhanced configuration and management. The luminaire should offer channel options of 8/ 4 channels by using a Programming kit, with these channels providing control for effects and colour transitions like 4 colour 4 channels, Master, Jump/ strobe, Micro function and speed. Additionally, it shall feature auto colour synchronization functionality, allowing seamless operation if there is a loss of DMX signal/ with loop in loop out. Power Input: DC 24V External Group Driver, Surge Protection: Inbuilt surge protection in the driver 2KV-4KV (Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection: IK07 or higher, Painting: Chemical 3/7 tank processed treatment before the powder coat black/Grey/approved colour coat. Fixture will be suitable to operate in a temperature range of -10°C to +60°C, the light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 50 degrees centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35-micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK07, HV & IP66 Certificates from NABL Accredited laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power & DMX Loop In/Out along with moulded connector having the length >300mm. Certifications: CE, RoHS, BIS. Make-Leksa lighting/Canara lighting/LT/Philips
284	SITC of DC power driver for the above Lights, Power : 200W, Input : AC 110-240V AC, 50Hz, Output : DC 12/24V, Protection rating, IP67, Surge protection : LL 4KV, LE 6KV Make-Leksa lighting/Canara lighting/LT/Philips
285	SITC of high quality DMX decoder, Power Input : DC 24V, Input Signal: DMX512, Addressing: You can manually set DMX addresses using DIP switches or digital displays, Smooth Dimming: Enables 0–100% dimming and dynamic effects like fading or color chasing. IP Rating: IP20. Make-Leksa lighting/Canara lighting/LT/Philips
286	SITC of PVC insulated multi core electrical un armored flexible 5C x 0.5Sq mm power cable having less electrical losses. (make-Polycab/ RR/ Finolex/ Havells/ KEI/ Gloster )
287	SITC of PVC insulated multi core electrical un armored flexible 3C x 1.5Sq mm power cable having less electrical losses. This PVC insulated and round sheathed wire features a bright multi strands copper conductors and it supports voltage grade up to 1100V. (make-Polycab/ RR/ Finolex/ Havells/ KEI/ Gloster )
288	SITC of 3cx2.5 sq.mm copper flexible cable with insulated cover with all other concerned materials as per direction of Engg.-in-Charge. Ncessary test report & Warrnaty certificate to be submitted to the department for genuinity of product & to avail free after sales service within warranty period for acceptance of materials(make-Polycab/ RR Kabel/ Finolex/ Havells/ KEI/ Gloster )
289	SITC of 5 core DMX cable comprises twisted pairs with shield support for carrying of data. DMX512 cable is used for connecting all light consoles that use DMX 512 standard data transmission. Make-Leksa lighting/Canara lighting/LT/Philips
290	SITC of IP65 \\"I\\" power connectors having 3/4 pole cable connector, chuck type strain relief, Current rating 20 A rms continuous, Easy and extremely precise locking system \\"Quick Lock\\" High impact materials - long-lasting and reliable. Make-Leksa lighting/Canara lighting/LT/Philips
291	SITC of IP65 \\"I\\" DMX connectors having 3/5 pole cable connector, Male/Female connector with improved latch, cage type contacts, \\"solder stop\\" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability.Make-Leksa lighting/Canara lighting/LT/Philips
292	SITC of 5 pin XLR Male connectors having 5 pole cable connector, Male/Female connector with improved latch, cage type contacts, \\"solder stop\\" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability.Make-Leksa lighting/Canara lighting/LT/Philips
293	SITC of 5 pin XLR Female connectors having 5 pole cable connector, Male/Female connector with improved latch, cage type contacts, \\"solder stop\\" for easy soldering, and additional ground contact for best contact integrity between chassis and cable connector. More durable housing for maximum reliability. Make-Leksa lighting/Canara lighting/LT/Philips
294	SITC of Outdoor type Power Distribution Panel made out by 2mm CRCA steel sheet duly derusted & painted by simens grey powder cote paint is designed as G.A drawing.as per direction of Engg.-in-Charge and external outgoing connecting points, fibre / brass glands of suitable size fitted MCB control for outgoing circuits. Timer with required contactor for auto switching. Power panel suitable for outdoor applicable and floor mount / wall mount options.Warranty period of replacement of panel & accessories must be 1 year & compelete test certificate must be submitted along with panel board including component list.3P+N Type 2 SPD 40 kA with 63A 4P MCB,10kA, Cseries shall be installed in the incomer. 20X10MM Separate Aluminium Earth bus bar should be installed.Busbar-04 numbers of 100Amps Aluminium busbar with 1A/SQ.MM current carring capacity. busbar duly sleeved by color coated PVC sleeve & supported by suitable size DMC insulator. (for outgoing) Outgoing-9 Nos of 6/10A SP MCB, C series, 10 kA Incomer-1No of 32A FP MCB, C series, 10 kA.Make-LEGRAND-DX3 / Siemens-Betaguard/ Schneider- Acti 9/ABB SB 200Make of SPD-Legrand/OBO/DEHN/ABB/Schneider/Siemens
295	SITC of IP 68 driver box made up of PVC / UPVC for the internal terminations and external outgoing connecting points, with required PVC / brass glands, Optional suitable size MCB fitted for control outgoing circuits.Make-Leksa lighting/Canara lighting/LT/Philips
296	SITC of DMX isolator or splitter provides Isolated optical DMX splitter provides 8 outputs from a 1 input and Input voltage: AC 110 to 220 V, 50 Hz, Product features: Group 1 & group 8 DMX signal change.Make-Leksa lighting/Canara lighting/LT/Philips
297	SITC of Din Rail Mount DMX controller can be used to control a wide variety of different DMX systems- from RGB/RGBW to more advanced moving and color mixing luminaires, DMX audio players and fountains. The controller comes with a variety of features, iPhone/iPad/Android remote control, Wi-Fi facilities, dry contact port triggering and flash memory.USB connection • 1024 DmX channels universe in live mode (computer) • 8 dry contact trigger ports via HE10 connector • stand alone mode with 5 area and 90+ scenes, Mac OSx 10.6/10.7/10.8 - Windows XP/VISTA/SEVEN/8 32/64 bits and USB 2.0, XLR3, mini USB, 1 HE10, Power From 5V to 5.5V DC (AC/DC adapter in option. The cost is inclusive of programming charges as per site conditions or client's approval (18 scenes ) Make-Leksa lighting/Canara lighting/LT/Philips
298	SITC of additional accessories for installing the lights as per the final drawing/site condition consisting of clamps, brackets, angles, steel conduits, covered cable tray, joints, hardware's like fasteners, nut & bolts etc.,
299	Supplying,installation,testing & commissioning of materials and installation of GI earth plate 600mmx600mmx6mm thick ISI marked with G. I. nut bolts & washers including cost of burnt wood charcoal, salt, foreign soil, water pouring arrangements, brick masonary enclosure on top with removable RCC cover complete with labour for excavation of pit in all kinds of soil & rock as required and as per direction of Engineer-in-charge.
300	Providing and fixing 6SWG dia GI wire on surface or in recess for loop earthing as required as per direction of Engg.-in-Charge.
301	Providing and fixing 25mm x 5 mm GI strip on surface or in recess for connections etc. as required as per direction of Engg.-in-Charge.
302	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes conforming to IS:15778, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge
303	20mm dia C - PVC pipe SDR - 11
304	25mm dia C - PVC pipe SDR - 11
305	32mm dia C - PVC pipe SDR - 11
306	40mm dia C - PVC pipe SDR - 11
307	Supplying all materials, labour T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all joiniting materials including cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.
308	15mm dia CP angle stop cock(FLR-ACR-5053N)
309	15mm dia CP two in one bib cock (Con-CHR-041KN Jaquar make)
310	15 mm dia CP S.B. Bib cock(CON-CHR-037KN)
311	15mm dia CP Pillar cock (Con-CHR-011KN Jaquar make)
312	25mm dia brass full way valve (Shakti make)
313	32mm dia brass full way valve (Shakti make)
314	40mm dia brass full way valve (Shakti make)
315	15mm dia CP Health faucet (Con-ALD-MCH-573 Jaquar make)
316	15mm CP Extension piece
317	125mm CP grating
318	15mm size C.P. flange
319	Supplying all materials , labour, T&P and fixing rotational moulded polyethylene cylindrical vertical water storage tanks conforming to IS:12701/1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc. including hoisting upto a height of 5 metres above ground level and placing the tank to the required position and providing 5.40 mtr. lengthx0.25 mtr width KB brickwork in cement mortar (1:6) of 0.46m height in staging and 0.13mtr thick circular protection wall of 0.46mtr height to support the tank,12mm thick cement plaster in cement mortar (1:6) over brick work, RCC slab of size 1.60mX1.60m and 0.10m thick ,RCC beam of 0.25mx0.30m and 3.40m average length in cement concrete (1:2:4) using 12mm size crusher broken hard black granite chips and required steel reinforcement including centering and shuttering,watering,curing ,cost of all materials,conveyance of all materials to worksite , payment of royalty, all taxes etc.all complete as per approved drawing , P.H. specification and direction of Engineer-in-charge
320	2000 liters capacity PVC water storage tank
321	supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking G.I. Pipes and fittings/ P.V.C. pipes and fittings including watering, curing, cost & conveyance of all materials to worksite, payment of royality, taxes etc. all complete as per direction of Engineer-in-charge.
322	Supplying all materials , labour, T&P and cutting holes in RCC floors and roofs upto 19cm thick for passing P.V.C pipes and G.I fittings etc. , and repairing the holes after insertion of pipe etc. with cement concrete (1:2:4) including finishing complete so as to make it leak-proof as per P.H. specification and direction of Engineer-in-charge
323	Supplying all materials, labour, T&P and cutting grooves in pucca floors and walls for taking G.I./P.V.C. pipes and making good the damages including watering , curing , cost & conveyance of all materials to worksite, payment of royality, taxes etc all complete as per direction of the Engineer-in-charge.
324	Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches , cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.
325	110mm U-PVC SWR Pipe (Supreme /Ashirvad)
326	110mm U-PVC ‘P’ Trap(Ori Plast/Finolex/Supreme Make)
327	110mm U-PVC door bend(Ori Plast/Finolex/Supreme Make)
328	110mm U-PVC Plain bend(Ori Plast/Finolex/Supreme Make)
329	110mm U-PVC offset without ear(Ori Plast/Finolex/Supreme Make)
330	110mm U-PVC Cowl(Ori Plast/Finolex/Supreme Make)
331	110mm U-PVC S/Jn door(Ori Plast/Finolex/Supreme Make)
332	110mm U-PVC Plain tee(Ori Plast/Finolex/Supreme Make)
333	110mm U-PVC D/Jn door(Ori Plast/Finolex/Supreme Make)
334	110mm U-PVC Door tee(Ori Plast/Finolex/Supreme Make)
335	110mm U-PVC Socket(Ori Plast/Finolex/Supreme Make)
336	Supplying all materials, labour, T&P and fixing vitreous china water closet, squatting pan (Indian type W.C pan/Orissa pattern squatting pan) duly embedded in cement concrete (1:5:10) using 4cm size hard granite metal including fixing a pair of vitreous china 250mm x 130mm x30mm footrest, fixing 100mm dia HCI 'p' or 's' trap (with/without 50mm dia horn) for water colset squatting pan including jointing the trap with pan in cement mortar (1:1) cutting the floor and mending good the damages , cost & conveyance of all materials to worksite, payment of royality , taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.
337	580mm size Orissa pan (Hindware/Parryware/Neycer make)
338	Supplying all materials, labour T&P and and fixing 12.50 liters/10 liters capacity low level flushing cistern with a pair of cast iron or M.S. brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle,unions and couplings for connection with inlet, outlet and overflow pipes, 32mm dia CP long flush bend, 15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connceting the inlet pipe with suupply main , cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge
339	10 ltr. Capacity pvc L.L. cistern with 32mm. Dia CP long flush bend ( Slimline-white-Parryware make )
340	Supplying all materials,labour,T&P and fixing Flat back lipped wall (Mini stall urinal -630mmx180mm) urinal of the following sizes including connecting the urinal with 32mm. dia pvc waste pipe 910mm. long by means of white lead mixed with chopped hemp, fixing 32mm. dia CP dome waste, 15mm. dia CP spreader including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc. all complete as per specification and direction of the Engineer in charge Half stall urinal
341	Supplying all materials, labour, T&P and fixing the following vitreous china Wash Down Water Closet(European type W.C. pan)with integral 'p' or 's' trap to the floor with wooden plug and chromium plated pedestal screws including jointing the trap with soil pipe in cement mortar (1:1) fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers including polishing , cost & conveyance of all materials to worksite, payment of royality, taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge
342	One piece commod(Hindware)ELEMENT Cat No.92084.
343	EWC(Matrix set)No.70002(P-18)
344	Supplying all materials, labour T&P and fixing wash basins with hole for pillar taps with cast iron or M.S.brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered 'Hot' and 'Cold' with long screws, shanks and back nuts of 15mm dia nominal bore, fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin, fixing 32mm dia CP brass waste, cost & conveyance of all materials to worksite, payment of taxes etc. all complete as perP.H specification and direction of the Engineer-in-charge
345	Under Counter basin(560x450)Hindware-No.10095
346	Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm.thick A.C. sheet or ply wood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of Engineer in charge.
347	Large Size mirror with Frame (11x0.90x0.75)=
348	Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge
349	CP soap holder (Jaquar)ACN-ACR-1131N
350	Supplying all materials , labour, T&P and cutting holes through existing brick or laterite masonry wall for taking U-PVC pipes and fittings including making good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge
351	Supplying all materials , labour, T&P and cutting of RCC chajja for taking HCI or U-PVC pipe and fittings including making good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge
352	Supplying all materials ,labour ,T&P and constructing Inspection Chamber of inside size 760mmx760mmx460mm with cement concrete (1:3:6) using 40mm size crusher broken hard black granite metal on bed , KB brick work in cement mortar (1:6) in foundation and plinth, moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size crusher broken hard black granite chips, 12mm thick cement plaster (1:3) with cement punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab (1:2:4) using 12mm size crusher broken hard black granite chips with R.C.C man hole cover, earth work in excavation in all kinds of soil and refilling the cavity around the chamber including watering,curing,cost of all materials, conveyance of all materials to worksite, payment of royalty,all taxes etc.all complete as per approved drawing, P.H specification and direction of Engineer-in-charge
353	Inside size 76cmx76cmx46cm with 18” dia RCC MH cover
354	Supplying all materials ,labour ,T&P and constructing gully trap chamber of inside size 250mmx250mm with 8cm thick RCC precast cover slab in cement concrete (1:2:4) mix using 12mm size crusher broken HG chips, foundation concrete (1:4:8) using 40mm size crusher broken HG metal on bed and around trap, KB brick work in cement mortar (1:6) in foundation and plinth and inside 12mm thick cement plastering (1:3) finished with a floating coat of neat cement including fixing 100mmx100mm size HCI gully trap, 150mmX150mm size CI grating etc.all complete as per drawing, specification and direction of Engineer-in-charge
355	Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized P.V.C. pipe conforming to IS 4985/2000 of the following out side dia for class- 3 (0.60mpa ) including jointing with supply of approved solvent cement by non-heat application method/as per manufacture's specification, provoding and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the type C-1 standard bedding surrounding or encasing including concrete for bedding and curing etc all complete as per P.H. specification and direction of the Engineer in charge
356	100mm dia P.V.C. pipe
357	150mm dia P.V.C. pipe
358	Supplying all materials labor T&P and constructing MH chamber of sizes earth work in excavation in all kinds of soil CC(1:1:8) with black granite chips size 46mm brick work with K.B. brick having crossing strength not less than 75 Kg /CM2 to 90 Kg/CM2s in CM(1:6)12mm C.P(1:8) inside MH chamber over benching with cement slush pointing (1:3)outside the MH chamber providing painting MS or CI step iron RCC(roof of slab with CC(1:2:4)with black granite chips size 12mm bending binding tying the grills placing of the reinforcement providing RCC color of required size refilling the cavity around the MH chamber with excavated earth including channeling the bed of MH etc all complete as per PH specification.
359	MH size 0.91m x 0.91 m with 0.45 m (18” dia RCC Cover )
360	Supplying all materials labour T&P and constructing 1.40m dia x 2.00 m deep soak way pit with dry brick having crossing strength not less than 75Kg/CM2 to 99Kg/CM2 in CM(1:6) for the remaining 0.4572mm height of wall at top CC(1:3)inside and outside inside fill with dry brick khoa size 38mm ,CM thick RCC perforated slab to a height of 1.9012m from bottom covered by means of 50mmthick RCC wall cover in pieces filled with iron plugs including earth work in excavation refilling of cavity around the pit and painting the iron works complete as per PHD design and specification including carriage of all materials to site.
361	Earth work in excavation of foundation in all kinds of soil within 50m initial lead and 1.5m initial lift including rough dressing & breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.30m in depth and as per direction of the Engineer-in-Charge.
362	Extra lifts of 1.50 mtr or part thereof over the initial lift of 1.5 mtr in all kinds of embankments and road works and ordinary earthwork in general.
363	Supplying all materials, labour, T&P and providing shoring and shuttering foundation trenches, pits etc with close wooden planks or sheets shuttering etc all complete as per direction of the Engineer in charge.
364	Supplying all materials, labour, T&P and filling in foundation and plinth with sand well watered and rammed including conveyance of all materials to worksite, payment of royalty, taxes etc.all complete as per direction of the Engineer in charge.
365	Supplying all materials, labour, T&P and providing cement concrete (1:3:6) with 4cm size hard granite metal including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge
366	Supplying all materials, labour, T&P and providing 6mm thick cement plaster (1:4) on RCC work including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge
367	Supplying all materials, labour, T&P and providing cement punning including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge
368	Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for R.C.C works including false work and dismantling them after casting including conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge
369	R.C.C beams,columns,girder and bressmer etc.
370	Supplying all materials, labour, T&P and providing M.S reinforcement for R.C.C work including cutting, bending, binding, and tying the grills and placing in position including cost of binding wire 18 to 20 gauge, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge
371	Supplying all materials, labour, T&P and providing cement concrete (1:1.5:3) with 12mm size hard broken granite chips for R.C.C works including hoisting, laying, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge
372	Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard broken granite chips including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge
373	Supplying all materials, labour, T&P and providing 12mm thick cement plaster (1:4) on brickwork including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge
374	Supplying all materials, labour, T&P and providing brick work with K.B bricks having crushing strength not less than 75kg/cm² with dimensional tolerance ± 8 percent in cement mortar (1:4) including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge
375	Supplying all materials, labour, T&P and making MS step iron in 20mm diameter MS steel bars and fixing into walls of man hole/septic tank duly embedded in cement concrete (1:3:6) complete as per specification and direction of the Engineer in charge.
376	Filling in foundation and plinth with excavated materials, moorum including watering and ramming as directed by the Engineer in charge
377	Earth work in excavation of foundation in all kinds of soil with in 1.5m initial lift including dressing and leveling of bed and breaking the clods and the excavated materials with in 50m initial lead as per direction of Engineer in charge.
378	Earth work in excavation of foundation in all kinds of soil with in 1.5m initial lift including dressing and leveling of bed and breaking the clods and the excavated materials with in 50m initial lead as per direction of Engineer in charge with 1st extra lift of 1.50 m over initial laft.
379	Supplying all labor T&P & filling foundation and plinth with excavated materials well watered & rammed etc. all complete as per direction of EIC.
380	Supplying all materials, labour, T&P and providing cement concrete ( 1:2:4 ) with 12mm size crusher broken hard black granite chips including watering, curing,cost of all materials, conveyance of all materials to work site with payment of royalty, all taxes etc all complete as per P.W.D specification and direction of Engineer-in-charge
381	Supplying all materials, labour, T&P and providing cement concrete (1:1½:3) with 12mm size crusher broken hard black granite chips for RCC works including hoisting, laying, watering, curing,cost of all materials, conveyance of all materials to worksite, payment of royalty,all taxes etc. all complete as per PWD specification and direction of the Engineer in charge.
382	Supplying all materials, labour, T&P and providing steel reinforcement of Fe-415 /Fe-500 grade for RCC work including cutting,bending,binding and tying the grills and placing in position including cost of binding wire 18 to 20 gauge,cost of steel, conveyance of all materials to worksite, payment of royalty,all taxes etc all complete as per PWD specification and direction of the Engineer-in-charge.
383	Supplying all materials, labour, T&P and providing rigid & smooth centering and shuttering for RCC works including false work and dismantling them after casting including conveyance of all materials to worksite, payment of royalty, taxes etc. all complete as per specification and direction of the Engineer-in-charge
384	RCC floor, roof slab chhaja up to 4.430 m height
385	Supplying all materials.labour.T&P and providing brick work in foundation and plinth with KB bricks having curshing strength not less than 75 kg/sqcm with dimensional tolerance+ 8% in cement mortar ( 1:3 ) including watering,curing,cost of all materials,conveyance of all materials to worksite,payment of royalty,all taxes etc.all complete as per PWD specification and direction of the Engineer in charge.
386	Supplying all materials,labour,T&P and providing 12mm thick cement plaster(1:3) on brick work including watering,curing,cost of all materials, conveyance of all materials to worksite,payment of royalty,all taxes etc.all complete as per PWD specification and direction of the Engineer-in-charge.
387	Supplying all materials,labour,T&P and providing 12mm thick cement plaster(1:6) on brick work including watering,curing,cost of all materials, conveyance of all materials to worksite,payment of royalty,all taxes etc.all complete as per PWD specification and direction of the Engineer-in-charge.
388	Supplying all materials, labour, T&P and providing cement punning including watering, curing,cost of all materials, conveyance of all materials to worksite, payment of royalty,all taxes etc. all complete as per specification and direction of the Engineer-in-charge
389	Supplying all materials labour T&P and fitting and fixing 12mm dia MS/CI step iron including supply of necessary CC(1:2:4) for fixing etc. complete as per PH specification.
390	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes conforming to IS:15778, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge
391	20mm dia C - PVC pipe SDR - 11
392	25mm dia C - PVC pipe SDR - 11
393	32mm dia C - PVC pipe SDR - 11
394	Supplying all materials, labour T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all joiniting materials including cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.
395	15mm dia CP angle stop cock(FLR-ACR-5053N)
396	15mm dia CP Pillar cock (Con-CHR-011KN Jaquar make)
397	25mm dia brass full way valve (Shakti make)
398	32mm dia brass full way valve (Shakti make)
399	15mm CP Extension piece
400	125mm CP grating
401	15mm size C.P. flange
402	Supplying all materials , labour, T&P and fixing rotational moulded polyethylene cylindrical vertical water storage tanks conforming to IS:12701/1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc. including hoisting upto a height of 5 metres above ground level and placing the tank to the required position and providing 5.40 mtr. lengthx0.25 mtr width KB brickwork in cement mortar (1:6) of 0.46m height in staging and 0.13mtr thick circular protection wall of 0.46mtr height to support the tank,12mm thick cement plaster in cement mortar (1:6) over brick work, RCC slab of size 1.60mX1.60m and 0.10m thick ,RCC beam of 0.25mx0.30m and 3.40m average length in cement concrete (1:2:4) using 12mm size crusher broken hard black granite chips and required steel reinforcement including centering and shuttering,watering,curing ,cost of all materials,conveyance of all materials to worksite , payment of royalty, all taxes etc.all complete as per approved drawing , P.H. specification and direction of Engineer-in-charge
403	2000 liters capacity PVC water storage tank
404	supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking G.I. Pipes and fittings/ P.V.C. pipes and fittings including watering, curing, cost & conveyance of all materials to worksite, payment of royality, taxes etc. all complete as per direction of Engineer-in-charge.
405	Supplying all materials , labour, T&P and cutting holes in RCC floors and roofs upto 19cm thick for passing P.V.C pipes and G.I fittings etc. , and repairing the holes after insertion of pipe etc. with cement concrete (1:2:4) including finishing complete so as to make it leak-proof as per P.H. specification and direction of Engineer-in-charge
406	Supplying all materials, labour, T&P and cutting grooves in pucca floors and walls for taking G.I./P.V.C. pipes and making good the damages including watering , curing , cost & conveyance of all materials to worksite, payment of royality, taxes etc all complete as per direction of the Engineer-in-charge.
407	Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches , cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.
408	110mm U-PVC SWR Pipe (Supreme /Ashirvad)
409	110mm U-PVC door bend(Ori Plast/Finolex/Supreme Make)
410	110mm U-PVC Plain bend(Ori Plast/Finolex/Supreme Make)
411	110mm U-PVC Plain tee(Ori Plast/Finolex/Supreme Make)
412	110mm U-PVC Socket(Ori Plast/Finolex/Supreme Make)
413	Supplying all materials, labour T&P and fixing wash basins with hole for pillar taps with cast iron or M.S.brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered 'Hot' and 'Cold' with long screws, shanks and back nuts of 15mm dia nominal bore, fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin, fixing 32mm dia CP brass waste, cost & conveyance of all materials to worksite, payment of taxes etc. all complete as perP.H specification and direction of the Engineer-in-charge
414	Under Counter basin(560x450)Hindware-No.10095
415	Supplying all materials, labour, T&P for fitting & fixing plain edge kitchen/wall sink of all standard sizes with a pair of bracket, C.P. waste, trap & P.V.C. waste pipe & painting brackets including supply of cement concrete & mortar etc. all complete. 24” x 18” x 10” sink
416	Supplying all materials, labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge
417	CP towel Ring(Jaquar)ACN-ACR-1121N
418	Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm.thick A.C. sheet or ply wood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of Engineer in charge.
419	Large Size mirror with Frame (5x0.90x0.75)=
420	Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge
421	CP soap holder (Jaquar)ACN-ACR-1131N
422	Supplying all materials , labour, T&P and cutting holes through existing brick or laterite masonry wall for taking U-PVC pipes and fittings including making good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge
423	Supplying all materials , labour, T&P and cutting of RCC chajja for taking HCI or U-PVC pipe and fittings including making good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge
424	Supplying all materials ,labour ,T&P and constructing gully trap chamber of inside size 250mmx250mm with 8cm thick RCC precast cover slab in cement concrete (1:2:4) mix using 12mm size crusher broken HG chips, foundation concrete (1:4:8) using 40mm size crusher broken HG metal on bed and around trap, KB brick work in cement mortar (1:6) in foundation and plinth and inside 12mm thick cement plastering (1:3) finished with a floating coat of neat cement including fixing 100mmx100mm size HCI gully trap, 150mmX150mm size CI grating etc.all complete as per drawing, specification and direction of Engineer-in-charge
425	Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized P.V.C. pipe conforming to IS 4985/2000 of the following out side dia for class- 3 (0.60mpa ) including jointing with supply of approved solvent cement by non-heat application method/as per manufacture's specification, provoding and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the type C-1 standard bedding surrounding or encasing including concrete for bedding and curing etc all complete as per P.H. specification and direction of the Engineer in charge
426	100mm dia P.V.C. pipe
427	Supplying all materials labour T&P and constructing 1.40m dia x 2.00 m deep soak way pit with dry brick having crossing strength not less than 75Kg/CM2 to 99Kg/CM2 in CM(1:6) for the remaining 0.4572mm height of wall at top CC(1:3)inside and outside inside fill with dry brick khoa size 38mm ,CM thick RCC perforated slab to a height of 1.9012m from bottom covered by means of 50mmthick RCC wall cover in pieces filled with iron plugs including earth work in excavation refilling of cavity around the pit and painting the iron works complete as per PHD design and specification including carriage of all materials to site.
428	Supplying all materials, labour, T&P for fitting & fixing plain edge kitchen/wall sink of all standard sizes with a pair of bracket, C.P. waste, trap & P.V.C. waste pipe & painting brackets including supply of cement concrete & mortar etc. all complete. 24” x 18” x 10” sink
429	Supplying all materials, labour, T&P and providing fitting and fixing (Aqua guard) pure chill 120 PSS UV of size 750 x 570 x 1350mm hight with water storage capacity 120 liter's along with 3 noa of faucets 2 for cold water and 1 for normal water including a flow of 1.5 ltr per munite etc all complete as per approved drawing , specification and direction of the Engineer in charge
430	Aqua guard pure Chill 120 PSS UV
431	Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized P.V.C. pipe conforming to IS 4985/2000 of the following out side dia for class- 3 (0.60mpa ) including jointing with supply of approved solvent cement by non-heat application method/as per manufacture's specification, provoding and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the type C-1 standard bedding surrounding or encasing including concrete for bedding and curing etc all complete as per P.H. specification and direction of the Engineer in charge
432	100mm dia P.V.C. pipe
433	Supplying all materials labour T&P and constructing 1.40m dia x 2.00 m deep soak way pit with dry brick having crossing strength not less than 75Kg/CM2 to 99Kg/CM2 in CM(1:6) for the remaining 0.4572mm height of wall at top CC(1:3)inside and outside inside fill with dry brick khoa size 38mm ,CM thick RCC perforated slab to a height of 1.9012m from bottom covered by means of 50mmthick RCC wall cover in pieces filled with iron plugs including earth work in excavation refilling of cavity around the pit and painting the iron works complete as per PHD design and specification including carriage of all materials to site.
434	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes conforming to IS:15778, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge
435	20mm dia C - PVC pipe SDR - 11
436	25mm dia C - PVC pipe SDR - 11
437	32mm dia C - PVC pipe SDR - 11
438	Supplying all materials, labour T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all joiniting materials including cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.
439	15mm dia CP angle stop cock(FLR-ACR-5053N)
440	15 mm dia CP S.B. Bib cock(CON-CHR-037KN)
441	15mm dia CP Pillar cock (Con-CHR-011KN Jaquar make)
442	25mm dia brass full way valve (Shakti make)
443	32mm dia brass full way valve (Shakti make)
444	15mm CP Extension piece
445	125mm CP grating
446	15mm size C.P. flange
447	supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking G.I. Pipes and fittings/ P.V.C. pipes and fittings including watering, curing, cost & conveyance of all materials to worksite, payment of royality, taxes etc. all complete as per direction of Engineer-in-charge.
448	Supplying all materials , labour, T&P and cutting holes in RCC floors and roofs upto 19cm thick for passing P.V.C pipes and G.I fittings etc. , and repairing the holes after insertion of pipe etc. with cement concrete (1:2:4) including finishing complete so as to make it leak-proof as per P.H. specification and direction of Engineer-in-charge
449	Supplying all materials, labour, T&P and cutting grooves in pucca floors and walls for taking G.I./P.V.C. pipes and making good the damages including watering , curing , cost & conveyance of all materials to worksite, payment of royality, taxes etc all complete as per direction of the Engineer-in-charge.
450	Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non-heat application method/as per manufacturer's specification, testing, earthwork in excavation in all kinds of soil and refilling of trenches , cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.
451	110mm U-PVC SWR Pipe (Supreme /Ashirvad)
452	110mm U-PVC ‘P’ Trap(Ori Plast/Finolex/Supreme Make)
453	110mm U-PVC door bend(Ori Plast/Finolex/Supreme Make)
454	110mm U-PVC Plain bend(Ori Plast/Finolex/Supreme Make)
455	110mm U-PVC offset without ear(Ori Plast/Finolex/Supreme Make)
456	110mm U-PVC Cowl(Ori Plast/Finolex/Supreme Make)
457	110mm U-PVC S/Jn door(Ori Plast/Finolex/Supreme Make)
458	110mm U-PVC Plain tee(Ori Plast/Finolex/Supreme Make)
459	110mm U-PVC Socket(Ori Plast/Finolex/Supreme Make)
460	Supplying all materials, labour, T&P and fixing vitreous china water closet, squatting pan (Indian type W.C pan/Orissa pattern squatting pan) duly embedded in cement concrete (1:5:10) using 4cm size hard granite metal including fixing a pair of vitreous china 250mm x 130mm x30mm footrest, fixing 100mm dia HCI 'p' or 's' trap (with/without 50mm dia horn) for water colset squatting pan including jointing the trap with pan in cement mortar (1:1) cutting the floor and mending good the damages , cost & conveyance of all materials to worksite, payment of royality , taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge.
461	580mm size Orissa pan (Hindware/Parryware/Neycer make)
462	Supplying all materials, labour T&P and and fixing 12.50 liters/10 liters capacity low level flushing cistern with a pair of cast iron or M.S. brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle,unions and couplings for connection with inlet, outlet and overflow pipes, 32mm dia CP long flush bend, 15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connceting the inlet pipe with suupply main , cost & conveyance of all materials to worksite, payment of taxes etc. all complete as per P.H specification and direction of the Engineer-in-charge
463	10 ltr. Capacity pvc L.L. cistern with 32mm. Dia CP long flush bend ( Slimline-white-Parryware make )
464	Supplying all materials, labour T&P and fixing wash basins with hole for pillar taps with cast iron or M.S.brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs, screws and cement etc, fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete, fixing pillar taps capstan head screw down high pressure lettered 'Hot' and 'Cold' with long screws, shanks and back nuts of 15mm dia nominal bore, fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin, fixing 32mm dia CP brass waste, cost & conveyance of all materials to worksite, payment of taxes etc. all complete as perP.H specification and direction of the Engineer-in-charge
465	550mmx400mm W.H.basin (Hindware/Parryware/Neycer make)with 15mm dia C.P.pillar cock (Plaza make) with 22” x 16” pedestal
466	Supplying all materials, labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge
467	CP towel Ring(Jaquar)ACN-ACR-1121N
468	Supplying all materials, labour, T&P and fixing mirror of superior glass mounted on 6mm.thick A.C. sheet or ply wood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of Engineer in charge.
469	Large Size mirror with Frame (11x0.90x0.75)=
470	Supplying all materials, labour, T&P and fixing CP soap holder complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge
471	CP soap holder (Jaquar)ACN-ACR-1131N
472	Supplying all materials , labour, T&P and cutting holes through existing brick or laterite masonry wall for taking U-PVC pipes and fittings including making good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge
473	Supplying all materials , labour, T&P and cutting of RCC chajja for taking HCI or U-PVC pipe and fittings including making good the damages etc. all complete as per P.H. specification and direction of Engineer-in-charge
474	Supplying all materials, labour, T&P and laying in trenches (to level or slope) unplasticized P.V.C. pipe conforming to IS 4985/2000 of the following out side dia for class- 3 (0.60mpa ) including jointing with supply of approved solvent cement by non-heat application method/as per manufacture's specification, provoding and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the type C-1 standard bedding surrounding or encasing including concrete for bedding and curing etc all complete as per P.H. specification and direction of the Engineer in charge
475	100mm dia P.V.C. pipe
476	Supplying all materials labour T&P and constructing 1.40m dia x 2.00 m deep soak way pit with dry brick having crossing strength not less than 75Kg/CM2 to 99Kg/CM2 in CM(1:6) for the remaining 0.4572mm height of wall at top CC(1:3)inside and outside inside fill with dry brick khoa size 38mm ,CM thick RCC perforated slab to a height of 1.9012m from bottom covered by means of 50mmthick RCC wall cover in pieces filled with iron plugs including earth work in excavation refilling of cavity around the pit and painting the iron works complete as per PHD design and specification including carriage of all materials to site.
477	Construction of 2nos production wells including scientific source finding through consolidated and unconsolidated rock with down the hammer drilling rig or combination rig with PVC pipe and installation of submersible pump set with all acessories
478	Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rig or combination rig as required to suit the site condition as per the direction of the Engineer in charge including use of own rig with its accessories, tools and plant and consumables etc for lowering of 200mm/150mm dia G.I/P.V.C/M.S casing pipes for housing fitted with socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation (G.I/ P.V.C/ M.S casing pipes if required to prevent collapse of overburden is to be provided by the contractor including lowering and withdrawing after completion of the tube well), 200mm dia to 400mm dia in overburden portion including packing of gravel supplied by the contractor for 400mm dia bore only
479	Drilling of 200mm dia bore00 mtr to 30mtr
480	30 mtr to 50mtr
481	Drilling of 150mm dia bore50 mtr to 215.00mtr
482	Lowering the following size of G.I/P.V.C/M.S housing pipes with or without slotted pipes as per the necessity from ground level up to 45.00m depth and fitted and fixed up in perfectly vertical position including cutting and threading of pipes and slotted pipes and supplying and fixing all jointing materials, tools and plant etc all complete and keeping the top of casing pipe threaded including plugging tube wells to prevent entry of foreign materials.
483	00 mtr to 30 mtrs
484	30 mtr to 60mtr
485	Supplying polyvinyl chloride pipes as per ASTM-D-1785-89 having threads in accordance with DIN 2999 part-1/DIN-42225 part-II specification length of pipe (laying length) will be 3 mtrs. The pipes shall be supplied with both external and threaded with free socket. The pipe having external thread at one end i.e female and or belled end. The female end having internal thread is to be belled in order to accept the male end while jointing pipes with a bore threading shall be provided with a greave at the roof of the male thread accomodate flexible PVC/Rubber 'O' ring to make the joint water tight colour of the pipe shall be blue. The name of the manufacture along with batch No class of pipe shall be stranded legibly of each pipe length.
486	200mm dia PVC (sch-80) pipe
487	Supplying all materials, labour, T&P and providing and providing sanitary sealing by cement concrete grouting of annular space around GI/PVC/MS housing pipe upto 5m below ground level (as per drawing) to plug the bore hole excluding cost of cement all complete as per direction of the Engineer in charge. Minimum one metre of casing pipe to be inserted in the bore into the rock at the bottom to ensure sanitary sealing (excluding cost of cement which will be supplied directly by the department)
488	Cleaning and developing the tube well with supply of compressor worked till clear and adequate discharge is obtained from the tube well including supply and use of all necessary equipment and labour as per direction of the Engineer in charge
489	By DTH Rig
490	Supplying all materials, equipment, labour & conducting reconnaissance survey, integrated Hydrological and Geophysical (Electrical Resistivity Method) survey & selection of potential source for exploration of Ground Water including selection and recommendation of site for drilling wells in selected locations in any part of Orissa under the following Geological formation:
491	Rocky terrain with boulder formation for 300m depth
492	Supplying all materials , labour T&P and providing consturction of plat form as per UNICEF specifcation etc.all completes as per direction of Engineer-in-Charge
493	Supplying all materials ,labour T&P and providing fitting and fixing India Mark-II hand pump with C I Cylender and connectiong roads with providing 24.00 mtr of 32 mm dia GI raiser pipe etc. all complete as per P.H Specification and direction of Engineer-in-Charge
494	Supplying all materials, labour, T&P and providing, fitting and fixing submersible pump with squirrel cage induction type submersible type submersible electric motor to run on 3 phase/1 phase line voltage ranging from 320 volt to 450 volt conforming to IS: 8034/89 with following specifications with suitable control panel, jointing with GI/PVC/HDPE pipes, electrification, testing, commissioning, trial running, conveyance of all materials to worksite, payment of taxes etc all complete as per specification and direction of the Engineer in charge (Texmo/Crompton Greaves/Kirloskar make)
495	2HP single phase 3 stage vertical / horizontal submersible pump set at head range 20 to 35 meters discharge 145 to 110 LPM with outlet dia of 25mm
496	DOL Control panel
497	40mm dia steel short piece
498	Well cap
499	50mm size CI bracket
500	2.50sqmm flat cable

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Odisha Tenders

Construction Tenders

Turnkey Projects Tenders

Infrastructure Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Infrastructure Development Of Ranipur Jharial At Bangomunda Block, Bolangir (Part-1), Ranipur-Odisha

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Infrastructure Development Of Ranipur Jharial At Bangomunda Block, Bolangir (Part-1), Ranipur-Odisha

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us