|
| 1 | Demolition of Brick or Stone Masonry built in cement mortar including pillar etc. complete all as apecified |
| 2 | M&L Brick Work with Fly Ash Modular Bricks straight or curved on plan to any radius built in cm 1:6 complete all as apecified |
| 3 | Taking down Cement Plaster on walls etc, including racking out joints, hacking for key, scrubbing down with water etc complete all as directed |
| 4 | M&L for Rendering 15 mm thick on Brick or Concrete surfaces in cement mortar 1:4 finished all as specified. |
| 5 | M&L Prepration of New Concrete Surfaces over 10 cm girth or width, not otherwise described and including Applying Two Coats of Synthetic Enamel Paint (Black / White / Yellow) over a coat of oil based Primer complete all as specified and directed. (Note : Work to be done on Road Side Kerb Stone) complete all as directed |
| 6 | M&L Prepration of Old Concrete Surfaces over 10 cm girth or width, not otherwise described and including Applying One Coats of Synthetic Enamel Paint (Black / White / Yellow) complete all as specified and directed. (Note : Work to be done on Road Side Kerb Stone) |
| 7 | Dismantling Stone Slabs and Tiles laid dry or laid dry and pointed of any description or thickness in floors, aprons etc all as specified and as directed. |
| 8 | Demolition of Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above GL) complete all as directed |
| 9 | M&L Hardcore of Gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as directed |
| 10 | M&L 100 mm thick PCC type B-1, 1:2:4 (20mm graded aggregate) as in Paving, Path and Hard Standing etc all as specified and directed. |
| 11 | M&L for 75 mm thick Cement Concrete type D4, 1:4:8 (40mm graded aggregate) as in Sub Base complete all as directed |
| 12 | M&L Crushed Sand / Manufacturer Sand / Stone Dust filling under Floors / Path in foundations and including watered and consolidation complete all as specfied and directed |
| 13 | M&L PCC 1:2:4 (20mm graded stone aggreagte) type B1 as in Copings, Kerbs Kneelers, Mass Concrete, Bed Plates, Water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as specified and directed |
| 14 | M&L 60MM thick Machine Pressed M35 Grade Factory Made Precast Concrete Inter Locking Paver Blocks with rubber finished/lacquer finish of any shape and size conforming to IS 15658- 2006 with grey cement and pigment complete all as specified and directed.. |
| 15 | M&L 80MM thick Machine Pressed M40 Grade Factory Made Precast Concrete Inter Locking Paver Blocks with rubber finished/lacquer finish of any shape and size conforming to IS 15658- 2006 of grade with grey cement and pigment complete all as specified and directed.. |
| 16 | Dismantling of Floor, Hearth or Wall Tilling incl cement mortar bedding (but not backing) and removing the rubbish off the premises out side MoD land complete all as specified and as directed by Engineer -in-Charge. |
| 17 | M&L for Coloured Non Skid Matte finish Endura Parking Tiles 12MM-16MM thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.16 sqm, in floors, steps, parking and paving etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including 15mm thick screed bed in cement morar 1:6 complete all as specified and as directed by Engineer -in-Charge. (Make of Tiles : Johnson, Somany, Kajaria, AGL, etc) |
| 18 | M&L Chequered Cement Concrete Tiles 30cm x 30cm x 25mm thick including 20mm thick Screed Bed or bedding layer of mortar in Cement Mortar 1:6 for lying floor finishes, set jointed and pointed in neat cement slurry with grey cement and pigments complete all as specified and as directed by Engineer -in-Charge. |
| 19 | M&L Providing and Laying at or near ground level Factory Made Kerb Stone of M-25 Grade Cement Concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand) and including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), making drainage opening wherever required as specified and directed. Please Enable Macros to View BoQ information |
