|
| 1 | Demolition/Dismantling of Brickwork or stone/ boulder masonry, built in cement mortar incl all quoins, arches, pillars, etc, complete all as specified and directed. |
| 2 | M&L for Brickwork with subclass 'B' bricks (old size bricks), straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed. |
| 3 | All as per item No 02 above but except bricks. |
| 4 | M&L for brick work with sub class ‘B’ bricks (old size brick) straight or curved on plan to any radius in half bricks thick walls, built in CM 1:4 complete all as specified and directed. |
| 5 | Taking down cement plaster of any description on concrete surfaces such as soffit of RCC slab, chajjas and brick walls, Ceiing etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed |
| 6 | M&L for rendering 15 mm thick cement plaster in CM 1:6 on brick Work or concrete surfaces including finished even and smooth without using extra cement all as specified and directed. |
| 7 | M&L for rendering 15mm thick in CM 1:4 on of brick work or concrete surface finish ever and smooth (w/o using extra cement) incl WPC as per user manual complete all as specified and directed. |
| 8 | M&L for rendering 10mm thick in CM 1:3 over concrete surface as on ceiling, chhajja, shelves etc to match with existing surfaces finish even and smooth w/o using extra cement complete all as specified and directed. . |
| 9 | M & L for preparation of new plastered surface and applying two coats of oil emulsion distemper on wall over one coat of primer incl one layer of 3mm thick wall care compound of altek/birla putty on old scraped surfaces or new plasterd surfaces and obtain smooth finish using sand paper complete all as specified and directed. |
| 10 | M&L for preparation of new plaster surface & apply two coats of cement based paint over a coat alkali primer resistance incl one layer of 3mm thick wall care compound of altek/birla putty on old scraped surfaces or new plasterd surfaces and obtain smooth finish using sand paper complete all as specified and directed. |
| 11 | M & L for preparation of new plastered surface and applying two coats of oil emulsion distemper on ceiling over one coat of primer incl one layer of 3mm thick wall care compound of altek/birla putty on old scraped surfaces or new plasterd surfaces and obtain smooth finish using sand paper complete all as specified and directed. |
| 12 | M&L for two coat of Acrylic smooth exterior emulsion paint over one coat of acrlic primer incl one layer of 3mm thick wall care compound of altek/birla putty for exterior/interior on old scraped wall/ceiling surfaces or new plasterd surfaces and obtain smooth finish using sand paper complete all as specified and directed.Note : Colour and make as approved by Engr-in-Charge. |
| 13 | Taking down chowkhats or frames with shutters not exc. 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed. |
| 14 | Taking down chowkhats or frames with shutters exc 1.5 Sqm but not exc. 4 Sqm each (without taking off shutters from the frames) complete all as specified and directed. |
| 15 | Taking down shutters of any description n exc 1 sqm each complete all as specified and directed. |
| 16 | Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed. |
| 17 | M&L for pressed steel frames of size 105mmx60mm for doors with one or more rebates fabricated out of 1.25mm thick mild steel sheets including necessary fixing lugs, butt hinges (100mm medium weight-03 Nos), lock strike plate with and including filling of hollow portion in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and making good the existing surface in cement mortar 1:6, complete all as specified and directed. |
| 18 | All as per item No 17 above but size of frame 125mmx60mm for doors. |
| 19 | S&F for 30mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed. |
| 20 | S&F for 2nd class H.W. glazed and skelton door shutters 35mm thick, open rebated and prepared to received glass/gauge etc (without sash bars) edges of framing plain, chamfered or rounded and mitred , beads for securing glass etc the size of member of shutter as specified in SSR part-I clause 8.23(b) and fitted to chowkahts incl stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads etc complete all as specified and directed. |
| 21 | S & F solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube incl taking down old frame any type complete all as specified and directed. |
| 22 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and raials with suitabale PVC sheet beading, and jointed together with solvant cement, fixing in the frame at side as per specification and drawing incl 3Nos- 100mm Aluminium hinges for each shutter complete all as specified and directed . |
| 23 | S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and directed. |
| 24 | M&L for factory made box type steel windows, 16 gauge steel section for frames & shutters, as per TD drawing No.219, sheet 01/03 to 03/03, using ERW hollow 'P' section comprising double frame for glazed and gauged skelton shutters jointed internally with flat iron 40X4 mm complete including grill of 10 mm square bar, fixed horizontally @ 10 cm centre to centre, pintel hinges 75 mm long 12 mm dia, 100 mm long handle, 150 mm long tower bolts, lugs etc. with/ without cooler provision, complete all as specified and directed. Note :- (i) For purpose of measurement and payment double shutter with frame including square grill shall be considered as one unit. (ii) Glazing and wire mesh shall be measured and paid for separately in respective of item. (iii) Item includes cost of double shutter of gauged and glazed shutter with square bar grill. |
| 25 | S&F in repair for factory made Solid WPC Door frame size ( 125mm X 65mm Double Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cbm & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawings including all necessary assories. The door frame should be Water Proof , Termite Proof , Fire Retardent and having excellent screw holding capacity, complete all as specified and directed. |
| 26 | S&F in repair for factory made Solid WPC Door frame size ( 100mm X 65mm Single Rebate ) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cbm & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawings including all necessary assories. The door frame should be Water Proof , Termite Proof , Fire Retardent and having excellent screw holding capacity, complete all as specified and directed. |
| 27 | S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 59-60 (SuspensionGrade) ,calcium carbonate and natural fibers(wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity indexof 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900N (Edge),minimum compressive strength 50 N/mm2,modulus of elasticity 850 N/mm2 and resistance to spread of flames of class A category with property of being termite /borer proof,water /moisture proof and fire retardant fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screw, complete all as specified and directed. |
| 28 | S&F Factory made solid panel PVC sketlton door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with. heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and Single Side Prelam PVC sheet used and stile & rails having one side feathered edge and on other side 10mm 900 bent edge for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wire gauzed i.e. panel will be of wire gauze in lieu of single side prelam PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed. |
| 29 | S&F window or ventilators made of roll formed pre painted galvanised steel ECO 4000 series (Base steel as per IS 513 of 0.58 mm thick \\"D\\" quality galvanized as per IS 277 with Zinc of 120 GSM); primer coated with epoxy primer of 5-7 micron thick, fininsh painted with a polyster paint of 12-16 microns thick and back coated with 5-7 micron thick alkyd backer. Section for outer frame should be 72x55 mm, centre mullion should be of 72x50mm, section for glass shutter should be 52x25 mm (irrespective whatever shown in the drawings) with concealed brackets Outer frame and mullions sections to hae rebate for glazed shutters, fly mesh and 20mm provision for guard bar/grills fly mesh shutter section should be 20x40 mm. The sections are to be cut to length mitre jointed with corner bracket. Centre mullions to be fixed with mullion cup. Stay, handle 2 nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 44 mm thick plain float glass and SS mesh for fly mesh shutter. Rubber Gasket are provided all around the glass. The above frame should be fixed to concrete/masonry wall by means of self expanding scew, including 12 mm square guard bars with 6\\" (152.4mm) pitch, complete all as specified as per Chief Engineer (AF) WAC Palam drg No CEAF/STD-191/2014 sheet 1/1 and 2/2 datde 11 Dec 2014 and complete all as specified and directed. |
| 30 | S & F steel windows or ventilators, fixed type,with glazing bars complete all as specified and directed. |
| 31 | S & F for 3mm thick sheet glass ordinary quality glazing with oil putty in square n exc 0.5 sqm quality or description from steel frame and complete all as specified and directed. |
| 32 | S & F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads complete all as specified and directed. |
| 33 | S & F in repair for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads complete all as specified and directed. |
| 34 | S & F in repair 3mm thick sheet glass, ordinary quality and with oil putty in Square n. exc 0.5 sqm in each pane incl hacking out old broken glass from metal frame incl punching or drilling out old glazing pins/spring clips and glazed with oil putty complete all as specified and directed. |
| 35 | S&F for MS butt hinges, medium weight, cold rolled mild steel 100mm long (ISI Marked) with welded or complete all as specified and directed. |
| 36 | S&F for aluminum anodized barrel tower bolts of extruded section 150mm long (ISI Marked) complete all as specified and directed. |
| 37 | S&F for aluminum handles cast type anodized 200mm long (ISI Marked) complete all as specified and directed. |
| 38 | S&F for 250mm long aluminium alloy, anodised, sliding door bolt of 16mm dia with hasp, staple (bolt type) and fixing clips of sheet, extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed. |
| 39 | S&F in repair, 150 mm ordinay rat tail rod pattern springs incl roller and rabber plate fixed to chowkhats in repairs incl necessary welding if reqd. complete all as specified and directed. |
| 40 | M&L for preparation of new steel or iron surfaces of any description not otherwise described over 10 cm girth or width and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as directed and specified. |
| 41 | M & L for one coat of synthetic enamel paint on steel surface including preparation of old steel surface width or girth exc 10cm complete all as specified and directed. |
| 42 | M&L for two coats of synthetic enamel paint over a coat of pink primer on wooden new surfaces of any description over 10cm width or girth incl preparation of new surfaces complete all as specified and directed. |
| 43 | M&L for one coats of synthetic enamel paint on wooden surfaces of any description over 10cm width or girth including preparation of old surfaces complete all as specified and directed. |
| 44 | M&L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 45 | M&L for 18mm thick water proof solid MDF Board prelaminated both sides of approved shade fitted with necessary arrangement as in kitchen cabinet back sides, partition, shutters and shelves, etc., fixed with solvent cement adhesive and stainless steel screws and providing 1mm thick PVC lipping to exposed edges, complete all as specified and as directed. |
| 46 | M&L for extruded brass handle, fancy type as approved by the GE, polished, 150mm long (ISI marked), complete all as specified and directed. |
| 47 | M&L for continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30mm, complete all as specified and as directed. |
| 48 | M&L for aluminium Fanlight catch with 14mm catch and fixed suitable for any shutters, complete all as specified and as directed. |
| 49 | S&F 125 mm size Hasp and staple, safety type mild steel,wire type,stove enamelled black,including bolt to hinge plate with screws complete all as specified and as directed. |
| 50 | S&F in repair 40 mm dia cupboard knobs fixed with nut, screw and washer of brass,bright finished complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 51 | S&F in repair 40 mm dia cupboard knobs fixed with nut, screw and washer of brass,bright finished complete all as specified and as directed. Please Enable Macros to View BoQ information |
