|
| 1 | Taking down defective self priming recirculation pump set of any type of capacity upto 3.5 HP Three phase by unscrewing the foundation bolts, disconnecting from water connection and electric motor, opening for inspection in presence of Engr-in-Charge and carry out repair at site such as replacement of ball bearing ,check nuts ,impeller,greasing ,gland,bush,casing gasket,nut bolt , washers etc and re-fixing, re-connecting in position, testing and commissioning complete all as specified and as directed by Engr-in-Charge. |
| 2 | Taking down defective self priming recirculation electric motor of capacity 3.5 HP from electric mains, isolating the necked connections, removing from foundation by unscrewing the nuts, bolts etc, discouple from pump, opening of motor including transporting to the workshop for rewinding of motor, cutting ,removing of burnt winding, cleaning and winding of motor with copper enameled wire of same gauge and turn of existing winding , varnishing, baking , reassembling , relpacement of bearings and transporting back to the site & re-connecting same to foundation including replacement of nuts, bolts washers etc. of suitable size, testing and commissioning complete all as specified and directed by Engineer-in-charge. . |
| 3 | Supply only for Alum (K2 SO4) for swimming pool for purifying the existing water complete all as specified and directed by Engineer-in-charge. |
| 4 | S&F under water light with housing water proof LED light fittings with Driver, LED-NP 300S, round light 18W/ 12 V PAR 56 144 LEDs and necessary fixing arrangement, fixed to concrete wall by means of long screws including making new hole by drilling machine and easily remove and fixing the fitting for future repair work with and including taking down unserviceable light fittings any type in swimming pool complete all as specified and as directed by Engineer-in-charge. Make:- Emaux cat part no 88045366 or equivalent in make Halbert. |
| 5 | S&F in repair LED driver CVD upto18W/12Volt, suitable for under water light with housing water proof LED light fittings with and including taking down unserviceable LED driver upto 18W/12Volt from fitting complete all as specified and directed by Engineer-in-charge . |
| 6 | S&F in replacement PVC vacuum hose pipe 30 mtr length upto 50mm dia (suitable for connection of existing pipe) for cleaning the swimming pool complete all as specified and directed by Engineer-in-charge. Make –Emaux/Halbert |
| 7 | S & F in replacement chemical testing kit for PH & chlorine of water complete all as specified and directed by Engineer-in-charge. |
| 8 | S&F UPVC pipe 75 to 90 mm including elbow, socket, Nipple, tee etc, all as per site requirement with and including taking out unserviceable UPVC pipe 75 to 90 mm complete all as specified and directed by Engineer-in-charge. |
| 9 | S&F UPVC pipe 110 to 160 mm including elbow, socket, Nipple, tee, reducer socket etc with and including taking out unserviceable UPVC pipe 110 to 160 mm all as per site requirement complete all as specified and directed by Engineer-in-charge. |
| 10 | S&F union suitable to UPVC pipe 75 to 90 mm with and including taking out unserviceable union 75 to 90 mm complete all as specified and as directed by Engineer-in-charge. |
| 11 | S&F union suitable to UPVC pipe 110 to 160 mm with and including taking out unserviceable union of size 110 to 160 mm complete all as specified and directed by Engineer-in-charge. |
| 12 | S&F Aqua seal lever operated butterfly valve suitable to UPVC pipe 75 to 90 mm with necessary fixing arrangement like flange, nut, bolts as per existing etc with and including taking out unserviceable valve 75 to 90 mm complete all as specified and directed by Engineer-in-charge. |
| 13 | S&F Aqua seal lever operated butterfly valve suitable to UPVC pipe 110 to 160 mm with necessary fixing arrangement like flange, nut, bolts as per existing with and including taking out unserviceable valve 110 to 160 mm complete all as specified and directed by Engineer-in-charge. |
| 14 | Supply and fixing in replacement of unserviceable sheet metal enclosure for distribution board SPN (when MCBs to be used) 8 way double door 200 Amps rated bus bar and with neutral, earthing bar and din rail complete all as specified and as directed by Engr-in-Charge. |
| 15 | S&F in replacement Standard curved poly Bristle wall brush 18'' including telescopic pole of suitable length complete all as specified and directed by Engineer-in-Charge. |
| 16 | S&F in replacement Leaf Skimmer of suitable size for swimming pool water cleaning complete all as specified and directed by Engineer -in -charge. |
| 17 | S&F in replacement (250x30) mm x 1 m white over flow grating single pin lock system complete all as specified and directed by Engineer -in -charge. Make:- Halbert/Emaux/Pentair. |
| 18 | Supply only Copper sulphate for colouring the water complete all as specified and directed by Engineer -in -charge. |
| 19 | Supply and Fixing in replacement of SP Series side mount filter valve of 6-way,dia 2\\" complete all as specified and directed by Engineer -in -charge. Make : Halbert/Emaux/Pentair. |
| 20 | Excavation in trenches not exc 1.5 meters wide and not exc 1.5 meters deep for pipe line in any type of soil, getting out and levelling of bottom surface to required level complete all as specified and as directed by Engineer-in-Charge. |
| 21 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed by Engineer-in-Charge. |
| 22 | Removing excavated material from site to a distance not exc 50 meters away and depositing where directed at a level not exc 1.5 meter from the starting point complete all as specified and as directed by Engineer-in-Charge. |
| 23 | Taking up CI/DI water main including all fittings with spigot and socket ends and lead/tyton joints including burning out lead joints and recovering lead of the 80 mm size of pipe complete all as specified and as directed by Engineer-in-Charge. |
| 24 | Taking up CI/DI water main including all fittings with spigot and socket ends and lead/tyton joints including burning out lead joints and recovering lead of the 100 mm size of pipe complete all as specified and as directed by Engineer-in-Charge. |
| 25 | Taking up CI/DI water main including all fittings with spigot and socket ends and lead/tyton joints including burning out lead joints and recovering lead of the 150 mm size of pipe complete all as specified and as directed by Engineer-in-Charge. |
| 26 | Supply & Laying, jointing, testing cast iron pipe with spigot socketed ends centrifully cast, class LA, tyton joints/ lead joint conforming to IS-1536-1976 laid in trenches of 80 mm dia sizes complete all as specified and as directed by Engineer-in-Charge. |
| 27 | M&L for 100 mm ductile iron pipe with spigot and socket ends, centrifugally cast, class k-9 (IS-8329-2000) with tyton joints in any length laid in trenches or fixed on pillars etc complete all as specified and as directed by Engineer-in-charge. |
| 28 | M&L for 150 mm ductile iron pipe with spigot and socket ends, centrifugally cast, class k-9 (IS-8329-2000) with tyton joints in any length laid in trenches or fixed on pillars etc complete all as specified and directed by Engineer-in-charge. |
| 29 | Material and labour for run lead joint including jointing material for cast iron pipe of 80 mm size/bore complete all as specified and as directed by Engineer-in-Charge. |
| 30 | Material and labour for run lead joint including jointing material for cast iron pipe of 100 mm size/bore complete all as specified and as directed by Engineer-in-Charge. |
| 31 | Material and labour for run lead joint including jointing material for cast iron pipe of 150 mm size/bore complete all as specified and as directed by Engineer-in-Charge. |
| 32 | Taking up or down 15mm dia bore GI tubing with connections including fittings complete all as specified and as directed by Engineer-in-Charge. |
| 33 | Taking up or down 20mm dia bore GI tubing with connections including fittings complete all as specified and as directed by Engineer-in-Charge. |
| 34 | Taking up or down 25mm dia bore GI tubing with connections including fittings complete all as specified and as directed by Engineer-in-Charge. |
| 35 | Taking up or down 40mm dia bore GI tubing with connections including fittings complete all as specified and as directed by Engineer-in-Charge. |
| 36 | Taking up or down 50mm dia bore GI tubing with connections including fittings complete all as specified and as directed by Engineer-in-Charge. |
| 37 | Taking up or down 80mm dia bore GI tubing with connections including fittings complete all as specified and as directed by Engineer-in-Charge. |
| 38 | Supply & Laying, jointing, testing GI pipe of 15 mm bore including fittings fixed to walls and ceiling or laid in floor, trench complete all as specified and as directed by Engr-in-Charge. |
| 39 | Supply & Laying, jointing, testing GI pipe of 20 mm bore including fittings fixed to walls and ceiling or laid in floor, trench complete all as specified and as directed by Engr-in-Charge. |
| 40 | Supply & Laying, jointing, testing GI pipe of 25 mm bore including fittings fixed to walls and ceiling or laid in floor, trench complete all as specified and as directed by Engr-in-Charge. |
| 41 | Supply & Laying, jointing, testing GI pipe of 40 mm bore including fittings fixed to walls and ceiling or laid in floor, trench complete all as specified and as directed by Engr-in-Charge. |
| 42 | Supply & Laying, jointing, testing GI pipe of 50 mm bore including fittings fixed to walls and ceiling or laid in floor, trench complete all as specified and as directed by Engr-in-Charge. |
| 43 | Supply & Laying, jointing, testing GI pipe of 80 mm bore including fittings fixed to walls and ceiling or laid in floor, trench complete all as specified and as directed by Engr-in-Charge. |
| 44 | Supply & Fixing gun metal gate valve suitable for 15mm bore dia pipe with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer-in-charge. |
| 45 | Supply & Fixing gun metal gate valve suitable for 20mm bore dia pipe with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer-in-charge. |
| 46 | Supply & Fixing gun metal gate valve suitable for 25mm bore dia pipe with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer-in-charge. |
| 47 | Supply & Fixing gun metal gate valve suitable for 40mm bore dia pipe with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer-in-charge. |
| 48 | Supply & Fixing gun metal gate valve suitable for 50mm bore dia pipe with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and as directed by Engineer-in-charge. |
| 49 | Supply and fixing including jointing and testing of cast iron sluice valves PN 1.6 class I, ISI mark flanged ends drilled having stainless steel / brass spindle with cast iron wheel at top complete with nuts, bolts, washers and gaskets for 80 mm bore complete all as specified and as directed. |
| 50 | Supply and fixing including jointing and testing of cast iron sluice valves PN 1.6 class I, ISI mark flanged ends drilled having stainless steel / brass spindle with cast iron wheel at top complete with nuts, bolts, washers and gaskets for 100 mm bore complete all as specified and as directed. |
| 51 | Supply and fixing including jointing and testing of cast iron sluice valves PN 1.6 class I, ISI mark flanged ends drilled having stainless steel / brass spindle with cast iron wheel at top complete with nuts, bolts, washers and gaskets for 150 mm bore complete all as specified and as directed. |
| 52 | Supply and fixing including jointing and testing of cast iron sluice valves PN 1.6 class I, ISI mark flanged ends drilled having stainless steel / brass spindle with cast iron wheel at top complete with nuts, bolts, washers and gaskets for 200 mm bore complete all as specified and as directed. |
| 53 | Material and labour for DI/CI specials such as Tees of any size and radius, collars, tapers, tail pieces, caps and plugs etc upto 150 mm bore complete all as specified and as directed. |
| 54 | Disconnecting existing defective electric motor of any make capacity of motor upto 5 HP from electric mains isolating the connections, removing from foundation by unscrewing the nuts, bolts etc, discouple from pump, opening of motor for inspection in presence of Engr-in-Charge & carrying out minor repairs at site and re-assembling the motor after repair, refixing in position re-connecting same as prior to removing from foundation including replacement of nuts, bolts washers of suitable size, testing and commissioning complete all as specified and directed. |
| 55 | All as per serial item No. 54.00 here-in-before but capacity of motor 40HP to 50HP complete all as specified and as directed. |
| 56 | Taking out old unserviceable/burnt copper winding of motors capacity upto 5 HP (defective motor taken out from Srl item No.62 above) and material and labour for rewinding of elect motor of capacity upto 5 HP, 3 Phase with super enameled copper winding wire of suitable gauge as per existing including cleaning of rotor, slots, all winding/insulation material, varnishing ball bearing ms shaft etc. complete and testing at site on full load after re-installation to the satisfaction of Engr-in-Charge all as specified and as directed. |
| 57 | All as per item No 56.00 here in before but taken out from 40 to 50 HP, 3 phase of any type & size complete all as specified and as directed. |
| 58 | Taking out defective centrifugal pump set of any type, make and capacity by unscrewing the foundation bolts, disconnecting from water connection, and disconnecting from electric motor, opening for inspection in presence of Engr-in-Charge and transported to contractor's workshop, repair the pump including replacement of unserviceable housing gasket -1 set, greasing, nut, bolt with washer and refixing, re-coupling in position, testing and commissioning complete including replacement of nuts, bolts, washers etc. complete all as specified and as directed. (single/3 phase upto 5 HP). |
| 59 | All as per item No 58.00 here-in-before but 40 to 50 HP 3 phase of any type & size complete all as specified and as directed. |
| 60 | S&F in replacement of shaft of existing material suitable for 40 to 50 HP pump set complete all as specified and as directed. |
| 61 | S&F in replacement of impeller of existing material suitable for 40 to 50 HP pump set complete all as specified and as directed. |
| 62 | S&F in replacement of shaft sleeve of existing material suitable for 40 to 50 HP pump set complete all as specified and as directed. |
| 63 | S&F in replacement of drive end bearing 6313 complete all as specified and as directed. |
| 64 | S&F in replacement of CI bearing Gauge complete all as specified and as directed. |
| 65 | S&F in replacement of gland assembly complete all as specified and as directed. |
| 66 | S&F in replacement of throat bush complete all as specified and as directed. |
| 67 | S&F in replacement of shaft coupling suitable for 40 to 50 HP pump set complete all as specified and as directed. |
| 68 | S&F in replacement of unsv Rotor body complete all as specified and as directed. |
| 69 | S&F of ball bearing of size 3309 complete all as specified and as directed. |
| 70 | S&F in replacement of unsv cooling fan suitable for 40 to 50 HP induction motor of any type complete all as specified and as directed. |
| 71 | Disconnecting, electrically, isolating the existing unserviceable MCCB of any make and capacity and Supply, fixing, connecting, testing and commissioning MCCB three phase, 415 volts fixed in existing panel including necessary modification for new MCCB, 400 Amp, 3 pole, breaking capacity 36 kA, conforming to relevant IS including all jointing and connecting material complete all as specified and as directed. Make:- Standerd/Havells/L&T. |
| 72 | All as per item No.71 here-in-before but 250 Amps, breaking capacity 36 kA, 4 Pole complete all as specified and as directed by Engineer-in-Charge. |
| 73 | All as per item No.71 here-in-before but 200 Amps, breaking capacity 35 kA, 4 Pole complete all as specified and directed by Engineer-in-Charge. |
| 74 | All as per serial item No. 71 here-in-before but 125 Amps, breaking capacity 25 kA, 3 pole complete all as specified and directed by Engineer-in-Charge. |
| 75 | All as per serial item No. 71 here-in-before but 100 Amps, breaking capacity 36 kA/ 25 KA, 3 pole complete all as specified and directed by Engineer-in-Charge. |
| 76 | All as per serial item No. 71 here-in-before but 63 Amps, breaking capacity 10 kA, 4 pole complete all as specified and directed by Engineer-in-Charge. |
| 77 | All as per serial item No. 71 here-in-before but 32 Amps, breaking capacity 10 kA, 3 pole complete all as specified and directed by Engineer-in-Charge. |
| 78 | Disconnecting and lifting out of existing submersible pump set from borewell capacity upto 7.5 HP alongwith their column pipe and submersible cable from bore well from any depth and lowering after repair complete all as specified and as directed by Engineer-in-charge. |
| 79 | Taking out old unserviceable/burnt copper winding of submercible pump capacity upto 7.5 HP (defective motor taken out from Srl item No.83 above) and material and labour for rewinding of submercible pump of capacity upto 7.5 HP, 3 Phase with super enameled PVC insulated copper winding wire of suitable gauge as per existing including cleaning of rotor, slots, all winding/insulation material, bearing etc. complete and testing at site on full load after re-installation and replacement of unserviceable parts to the full satisfaction of Engr-in-Charge complete all as specified and as directed. |
| 80 | M&L for Servicing of submersible pump set including replacement of thrust plate shaft sleev, spacer, impeller - 04 Nos, SS shaft - 01 No, stud 4 Nos and filling of water and making it water tight complete all as specified and as directed by Engineer-in-charge |
| 81 | S&F in replacement GI column pipe 50mm dia heavy duty class 'C' with GI flanged and drilled at both ends duly threaded and welded of 3 mtr long alongwith cut for passing the submersible cable including bolts, nuts, washers and rubber insertions packing complete all as specified and directed by Engineer-in-charge. |
| 82 | S&F in replacement GI column pipe 80mm dia heavy duty class 'C' with GI flanged and drilled at both ends duly threaded and welded of 3 mtr long alongwith cut for passing the submersible cable including bolts, nuts, washers and rubber insertions packing complete all as specified and directed by Engineer-in-charge. |
| 83 | Supply, connecting, testing and commissioning submersible cable with copper conductor, stranded of size 4 sqmm 3 core complete including dismantling the old unserviceable cable complete all as specified and as directed. |
| 84 | Supply, connecting, testing and commissioning submersible cable with copper conductor, stranded of size 6 sqmm 3 core complete including dismantling the old unserviceable cable complete all as specified and as directed. |
| 85 | S&F in replacement water proof joint for submersible cable suitable for size 4/6 sqmm 3 core complete all as specified and as directed by Engineer-in-charge. |
| 86 | Supply, installation, testing and commissioning of pressure pumpset 1 HP with automatic pressure switch which switches the pump on and off based on turning on and off of the Tap, air tank of suitable capacity, pressure gauge etc with and including taking down unserviceable pressure pump set complete all as specified and as directed by Engineer-in-Charge. |
| 87 | M&L CI Non return valve without by pass arrangement confirming to IS-5312 part-1, PN 1.0 including nuts, bolts, washers and gaskets including taking out old unserviceable NRV 100 mm dia complete all as specified and as directed by Engineer-in-charge. |
| 88 | M&L CI Non return valve without by pass arrangement confirming to IS-5312 part-1, PN 1.0 including nuts, bolts, washers and gaskets including taking out old unsv NRV 150 mm dia complete all as specified and as directed by Engineer-in-charge. |
| 89 | Material and Labour for in replacement CI foot valve flanged type including nuts, bolts, washers and rubber 150 mm dia confirming to IS-4038 complete all as directed by Engineer-in-Charge. |
| 90 | Supply only CDD 5000 (two components chlorine dioxide powder) (CAS No 10049-04-4 conforming to ISO9001-2015) white in colour highly soluble in water, 99.9% effective against water borne micro organisms disinfectant for chlorination of water complete all as specified and directed by Engr-in-charge. |
| 91 | M&L for Flushing of existing borewells of size upto 300mm dia, depth upto 200 mtr with drilling compressor including surging and flushing the bore at a pressure of 7 kg/ sqcm minimum 8 hrs, complete with compressed air and flushing the sand, mud etc from the bore well complete all as specified and directed by Engr-in-charge. Note:- Disconnecting and lifting out of existing submerssible pumpst from borewell upto 10 HP capacity along with their column pipe and submerssible cable from borewell from any depth and lowering after flushing existing borewell shall be deemed to be included the unit item rate. |
| 92 | M&L for chemical and bacteriological analysis and potability of water obtained from Delhi Jal Board & borewells from Sriram Test House/ MCD approved micro engineering and testing lab and submitting the report in duplicate complete all as specified and as directed by Engineer-in-charge. Note:- The Report shall be carried out quarterly and submit to GE for verification and record. |
| 93 | Opening the pressure filter 1200mm dia installed at swimming pool equipment room removing the old filter media, removing all the scaling deposited on the surface area of filter assembly by using wire brush and cleaning the filter with HCC, refilling new filter media of various silica grade as required at site, re-assembling the filter assembly and apply one coat of good quality paint on the outer surface area of filter assembly and testing for leakage of proper functioning and testing complete all as specified and directed by Engr-in-charge. |
| 94 | M&L for earthing complete with Galvanised steel earth plate electrode 600mm x 600mm x 6mm buried directly in the ground vertically to depth not less than 2.25 Mtr below the ground level with the top edge of earth plate, depth not less than 1.5 Mtr below the ground level connected to GI earth strip of 25mm x 4 mm size by means of bolts, nuts and washers protected by GI tubing light grade 40 mm dia uptoTest point 20 mm dia watering pipe with funel & wire mesh, PCC pit in mix (1:2:4) (using 20 mm graded stone aggregates) chamber, 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded stone aggregates complete all as specified and shown in Electrical plate No.3 of SSR Part-I including earth work in any type of soil, removal of surplus soil and providing charcol dust & salt layers all around the earth plate upto 15 cm all as required specified & directed by Engr- in -charge. Note:- Up to 7.5 Mtr length of pipe of 40 mm dia and GI strip shall be deemed to be included in unit rate quoted by tenderer. GI pipe and GI strip beyond 7.5 shall be measured and paid separately under respective items. |
| 95 | Supply and fixing Auto timer clock as per existing complete all as specified and directed by Engineer-in-Charge. |
| 96 | Supply and fixing of single phase preventor VSP-2 / VSP-1 complete all as specified and as directed by Engr-in-Charge. Make: -Minilac/ L &T/ Lagrand |
| 97 | Material & Labour for painting to existing centrifugal motor & pumping set complete including base frame with super enameled paint of existing colour coat by spray painting and writing of SM/MES No with white paint, 40 to 50 HP capacity all as specified and directed by Engineer-in-Charge. |
| 98 | All as per item No 97 above but upto 5 HP capacity any type and make complete all as specified and as directed. |
| 99 | Material and labour for Servicing of liquid chlorine dosing system, any make, any type/capacity complete including replacement of chlorine dosing pipe upto 2.5 mtr length for each plant including servicing of motor, washing of chlorine tank with descaling agent and re-commissioning testing of plant complete all as specified and as directed. |
| 100 | Supply and fixing for Amps meters 0 to 200 Amps, Digital type with selector switches, CTs etc complete all as specified and as directed by Engineer-in-charge. |
| 101 | Supply and fixing for volt meters 0 to 500 Volt, Digital type 415 volts with selector switches, CTs etc complete all as specified and directed by Engineer-in-charge. |
| 102 | Supply and fixing LED indicator lamps (R,G,Y) complete all as specified by Engineer-in-charge. |
| 103 | Supply and fixing Automatic pressure control switch suitable for pressure pump of capacity upto 1.0 HP complete all as specified and as directed by Engineer-in-charge. |
| 104 | Supply and fixing pressure gauge 0-10 Kg/ Sqcm suitable for pressure pump complete all as specified and directed by Engr-in-charge. |
| 105 | Supply and fixing air tank of suitable capacity as per existing for pressure pump of capacity upto 1.0 HP complete all as specified and as directed by Engr-in-charge. |
| 106 | Material and Labour for cutting of hard standing upto suitable depth for inserting the pipe upto 250mm bore dia/ Cables of any size and making good the disturbed surfaces with paste pre mix bituminous 50mm thick polymer based material over WBM 75mm thick including rolling work etc complete all as specified and as directed by Engineer-in-Charge. |
| 107 | Supply and fixing in replacement of unserviceable display board for showing details of pump houses and borewells as provided by Engineer -in-charge made out of white PVC sheet of size 1.5mtrX1mtr including GI angle frame and GI sheet cover to the frame and fixing of 2 nos LED tube light fittings 20 watts, connecting electrical supply to the frame with cable 2 core 1.5 sqmm to connect from electric source and making arrangement for replacement of tubelights including round steel pole minimum 12 feet long of suitable dia for erection on ground with PCC complete all as specified and as directed by Engineer-in-charge. |
| 108 | M&L for painting of water supply header of size 100/150/200/250/300mm dia with two coat of synthetic enamel paint with a suiatble colour as per instruction complete all as specified and directed by Engr-in-charge. |
| 109 | Supply only in replacement of stainless steel vaccuum suction head 36\\" suitable for swimming pool cleaning including necessary wheel complete all as specified and as directed by Engineer-in-Charge. |
| 110 | Supply and fixing BI metallic over load relay, range 36-60 amp rating for automatic starters complete all as specified and directed by Engineer-in-charge. Make:- Legrand/LT |
| 111 | All as per item No 110 above but 9-15 Amps complete all as specified and directed by Engineer-in-charge. |
| 112 | M&L for augering of holes in true horizontal position under road by trench less method by means of mechanical rig covering in route upto 1.5 mtr deep and not exceeding 30 mtr long for passing the water pipe lines upto 150mm bore all as specified and as directed by Engr-in-Charge. |
| 113 | Supply and fixing in replacement of unserviceable power contactor MNX 50-70 Amps suitable for 40 to 50 HP pumping set complete all as specified and directed by Engr-in-charge. |
| 114 | Supply and fixing in replacement of unserviceable power contactor HGS 50-65 Amps suitable for 40 to 50 HP pumping set complete all as specified and directed by Engr-in-charge. |
| 115 | Supply, fixing, commissioning and testing Digital display board wall mounted outdoor type of size 5.3 ft width 2.1 ft height (11.13 Sq Feet), Screen size 160 cm x 64 cm, Pixel pitch P4 outdoor incl LED controller, BIS certified ISO 9001 Certified MSME complete including programming as details provided by Engr-in-Charge, water proof IP65, Content support reqd Image, Text and Video and USB/ Ethernet/ wifi connectivity, display should be remote supported complete all as specified and directed by Engr-in-Charge.Note:- Fittings required for installation like wall mount and connected items shall be deemed to be included in item rate. |
| 116 | Dismantling floor, hearth or wall tiling including cement mortar bedding and removing debries off the premises complete all as specified and as directed by Engr-in-charge. |
| 117 | Taking down cement plaster on brick or concrete wall surfaces etc including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed by Engr-in-charge. |
| 118 | M&L for 15mm thick rendering on brick or concrete wall surfaces in cement mortar (1:4), surface finished even and smooth without using extra cement complete all as specified and as directed. |
| 119 | M&L for preparation of new plastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and as directed. |
| 120 | M&L for complete removal of existing treatment of old plastered surfaces on walls including brooming down or steel wire brushing, scraping down and applying two coats of distemper oil emulsion over one coat of alkalic resistant primer complete all as specified and as directed by Engineer - in- charge. |
| 121 | M&L for complete removal of existing treatment of old decorated external surface of walls by electrically operated grinder including necessary scaffolding complete and applying two coats of exterior emulsion paint over a coat of primer of same brand over 2mm thick (avg thickness) cement based wall care putty to obtain even and smooth surfaces including preparation of surfaces complete all as specified and as directed by Engineer - in- charge. |
| 122 | S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated, fancy type, long/ short body screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. |
| 123 | S & F in repair cast copper alloy CP Soap dish complete all as specified and as directed. |
| 124 | S & F in repair cast copper alloy CP towel ring complete all as specified and as directed. |
| 125 | S&F in repairs vitreous china wash down water closet pan (pedestal pattern), and trap white (excluding flushing cistern and seat cover) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc complete all as specified and as directed by Engineer-in-Charge. |
| 126 | S&F in repairs 15mm bore angle cock, chromium plated, screwed down, high pressure, with crutch or butterfly handles, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 127 | S&F in repairs, 15mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all specified and as directed by Engr-in-Charge. |
| 128 | S&F in repair health faucet with double lock 1 meter brass plated stainless steel flexible hose and wall hook complete all as specified and as directed. |
| 129 | S & F in repair CP toilet paper holder complete all as specified and as directed. |
| 130 | S&F in repair plastic water closet seat cover, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and as directed by Engineer-in-Charge. |
| 131 | S&F in repair PVC valveless, syphonic action type, flushing cistern low level, 10 litre capacity, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed. |
| 132 | S&F in repair brass chromium plated shower rose 125 mm size fixed to 15 mm bore iron pipe complete all as specified and as directed by Engineer-in-Charge. |
| 133 | S&F in repair 500 litres capacity rotational moulded, three layered, white, polyethene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed. |
| 134 | S&F in repair 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and as directed. |
| 135 | M&L for snow glazed blue blend ceramic swimming pool tile in floor and wall surfaces, set and jointed with adhesive including pointing etc complete all as specified and as directed. |
| 136 | Demotion of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 137 | M&L for chequered cement concrete tiles of size (30cm x 30cm) x 25mm thick, set, jointed and pointed in neat cement slurry as in floors with and including over 20mm thick scread bed with cement mortar (1:6) complete all as specified and as directed. Please Enable Macros to View BoQ information |
