Tender For Special Repair To Shaft Area Of Map Buildings And Misc Works At Camero Complex Under Ge (Af) Subroto Park, Delhi Cantt-10
Tender Value
1.44 Crore
Estimated cost
Bid Submission
17 Aug 2026
2 days left
EMD
2.20 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Subroto Park → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Shaft Area Of Map Buildings And Misc Works At Camero Complex Under Ge (Af) Subroto Park, Delhi Cantt-10
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 30-Jun-2026 | Corrigendum No 1 | Date | 16-Jul-2026 |
| 2 | 07-Jul-2026 | Corrigendum No 2 | Date | 23-Jul-2026 |
| 3 | 14-Jul-2026 | Corrigendum No 3 | Date | 30-Jul-2026 |
| 4 | 21-Jul-2026 | Corrigendum No 5 | BOQ | 03-Aug-2026 |
| 5 | 21-Jul-2026 | Corrigendum No 4 | Date | 03-Aug-2026 |
| 6 | 03-Aug-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 10-Aug-2026 |
| 7 | 12-Aug-2026 | Corrigendum No 6 | Date | 17-Aug-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement or cement lime plaster any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge. |
| 2 | M&L for rendering plaster in CM (1:6) 10 mm thick on fair faces of brick work or concrete surfaces etc including finished even and smooth without using extra cement up to Nine storey height bldg and removing the debries outside the MOD land complete all as specified and directed by Engr In Charge. |
| 3 | M&L rendering plaster 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth with out using extra cement up to Nine storey height bldg and removing the debries outside the MOD land complete all as specified and directed by Engr In Charge. |
| 4 | M & L rendering plaster 5mm thick on ceiling in cement mortar 1:3 finished fair and even smooth without using extra cement etc built in cement mortar and removing the debries outside the MOD land complete all as specified and directed by Engr In Charge. |
| 5 | M&L for preparation of new plastered surfaces of walls, and applying two coats of distemper oil emulsion over a coat of primer incl 3mm thick elastomeric wall care putty on walls up to nine storey height building complete and specified and as directed by engr-in -charge. |
| 6 | M&L for prepration of old plastered or unplastered surfaces of walls and applying two coat of approved shade of oil emulsion distemper, including repairing of pot holes and cracks with putty, up to Nine storey height building complete all as specified and directed by Engr-in-Charge. |
| 7 | M&L for preparation on new or previously untreated wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces over putty up to nine storey height building complete all as specified and directed by Engineer-in-Charge. |
| 8 | M&L for complete removal of existing old surface wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surface over putty up to nine storey height building complete all as specified and directed by Engineer-in-Charge. |
| 9 | M&L preparation of new plastered or unplastered surface and applying three coats of white wash on ceiling up to nine storey height building complete and all as specified and directed by engr-in -charge. |
| 10 | M & L preparation of old plastered surface and applying two coats of white wash on ceiling up to nine storey height building complete and all as specified and directed by Engr-in -Charge. |
| 11 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) |
| 12 | S&F in PVC (SWR) pipes 110 mm single socketed, in any length with solvent cement joints fixed to walls/laid in floors up to nine storey height building etc complete all as specified and directed by Engr In Charge. |
| 13 | S&F in PVC (SWR) pipes 75 mm single socketed, in any length with solvent cement joints fixed to walls/laid in floors up to nine storey height building etc complete all as specified and directed by Engr In Charge. |
| 14 | S&F for 110 mm dia pvc pipe Stack clamps out of 50 mm by 5mm flat iron and 16mm dia round iron stays,enlcuding bolts and nuts and securing ends of stays to wall or roof up to nine storey height building as per complete all as specified and directed by Engr In Charge. |
| 15 | S&F for 75 mm dia pvc pipe Stack clamps out of 50 mm by 5mm flat iron and 16mm dia round iron stays,enlcuding bolts and nuts and securing ends of stays to wall or roof up to nine storey height building as percomplete all as complete all as specified and directed by Engr In Charge. |
| 16 | S&F in repair PVC SWR bends 110 mm up to nine storey height building complete all as specified and directed by Engr In Charge. |
| 17 | S&F in repair PVC SWR bends 75 mm up to nine storey height building complete all as specified and directed by Engr In Charge. |
| 18 | S&F in repair 110 mm PVC SWR Junction single (Single T) provided with access door complete up to nine storey height building all as specified and directed by Engr In Charge. |
| 19 | S&F in repair 75 mm PVC SWR Junction single (Single T) provided with access door complete up to nine storey height building all as specified and directed by Engr In Charge. |
| 20 | S&F in repair PVC SWR Junction piece 110 mm double (Double T) provided with access door equal or unequal complete up to nine storey height building all as specified and directed by Engr In Charge. |
| 21 | S&F in repair PVC SWR Junction piece 75 mm double (Double T) provided with access door equal or unequal complete all as specified and directed by Engr In Charge. |
| 22 | S&F in repair 110 mm PVC SWR Branch piece, double (Single Y) complete all as specified and directed by Engr In Charge. |
| 23 | S&F in repair 75 mm PVC SWR Branch piece, double (Single Y) complete all as specified and directed by Engr In Charge. |
| 24 | S&F in repair PVC SWR vent cowl of size 110 mm complete all as specified and directed by Engr In Charge. |
| 25 | S&F in repair PVC SWR vent cowl of size 75 mm complete all as specified and directed by Engr In Charge. |
| 26 | Taking up or down steel tubing or removing from site of 15mm bore pipe up to nine storey height building all as specified and directed by Engineer-in-charge. |
| 27 | All as above item No 26 but 20mm bore. |
| 28 | All as above item No 26 but 25-32mm bore. |
| 29 | All as above item No 26 but 50 mm bore. |
| 30 | S&F for 15mm bore steel water tubing medium grade , galvanized ISI marked with all fittings fixed to wall & ceiling or laid in floors complete all as specified and directed by Engineer-in-charge. |
| 31 | All as per item No 30 above but 20mm bore |
| 32 | All as per item No 30 above but 25mm bore |
| 33 | All as per item No 30 above but 32mm bore |
| 34 | All as per item No 30 above but 50 mm bore |
| 35 | S&F in repair gun metal globe balve ot gate valve with mild steel iron wheel head, screwed both ends for iron pipe & fifed for 20 mm bore up to nine storey height building complete all as specified and directed by Engr In Charge. |
| 36 | All as per item No 35 above but 25 mm bore |
| 37 | All as per item No 35 above but 32 mm bore |
| 38 | All as per item No 35 above but 50 mm bore |
| 39 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) area n. exc 1.5 sqm complete all as specified and directed by Engr In Charge. |
| 40 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 andresistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance indimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 41 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900N (Edge),minimumcompressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 42 | S&F 150 mm long Aluminium anodised, barrel tower bolts of ex- truded section and fixed complete and specified and directed by engr-in -charge. |
| 43 | S&F 150mm long aluminium handle cast type polished bright complete and specified and directed by engr-in -charge. |
| 44 | S&F 100 mm long butt hinges medium weight, mild steel, and fixed complete and specified and directed by engr-in -charge. |
| 45 | Supply only liquid water proofing compund only complete all as specified and directed by Engr In Charge. |
| 46 | Demolition of cement concrete in sunken portion in any position not otherwise specifically provided for complete all as specified and as directed by Engineer-in-Charge. |
| 47 | Providing and making fillet of 75mmx75mm in size with cement concrete in 1:2:4 in sunken portion, complete all as specified and directed by Engr In Charge. |
| 48 | Refilling Lime concrete with brick aggregate (Course) in lime mortar1:3, in the sunken with the help of proper tools & equipments & plants complete all as specified and as directed by Engineer-in-Charge. |
| 49 | Material and labour for Sunken treatment with following steps:-(a) All pipes passing through walls of sunken One No.50 mm dia, 35 cm long medium grade Gl pipe with wire gauge on inside mouth shall be provided to each sunken portion. (b) Clear the sunken/lowered portion of RCC slab surface for full depth of sunken floor by wire brush. Chisel out any mortar sticking the surface.(i) Applying FOSROC Nitoproof 600PF (minimum 0.8 mm dft) over a priming coat of Nitoproof WB Primer or equiyalent product of Asian paints, M/s MC Bauchemie / CIPY / SIKA/ Pidilite Dr Fixit / Thermax / STP applied as per manufacturer's instructions to bottom and fullvertical sides of sunken floors. (ii) Fill it with water and check for dampness and seepage. In case the slightest indication of seepage/leakage is noticed, the same shall be rectified by injection grouting to seal all cracks or application of Polymer modified mortar FOSROC Nitobond SBR or equivalent of M/s MC Bauchemie / CIPY / SIKA / Pidilite Dr Fixit / Asian paints / Thermax/STPadmixed with Integral WPC or cementitious crystalline waterproofing compound in the affected area to seal all cracks and micro cracks if any, and this shall be done by Contractor at his own cost.(iii) Apply additional coat of FOSROC Nitoproof 600 PF or equivalent or Asian paints /M/s MC Bauchemie / CIPY / SIKA/ Pidilite DrFixit / Thermax / STP.All junction points of side walls where CI/GI pipes are passing through shall be sealed with epoxyCement mortar. |
| 50 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.complete all as specified and directed by Engr In Charge. |
| 51 | M&L Glazed ceramic coloured tiles in vertical surface 450x300x7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match incl back plaster 10 mm thick in cm 1:4 up to Nine storey height bldg complete all as specified and directed by Engr In Charge. |
| 52 | M&L for non skid ceramic joint free coloured tiles 8mm thick, (square or rectangular) area of each tile n. exc 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed in CM(1:6) up to Nine storey height bldg complete all as specified and directed by Engneer-in-Charge. |
| 53 | S&F in repair for vitreous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/ white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, excluding fixing bolts, flushing cistern and flush pipe) complete all as specified. |
| 54 | S&F in repair PVC SWR floor trap including jointing with solvent cement 75 mm dia complete up to nine storey height building all as specified and directed by Engr In Charge. |
| 55 | S&F in repairs10 ltr capacity PVC flushing cistern coloured with accessories Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete and specified and directed by engr-in -charge. |
| 56 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mmthick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engr In Charge. |
| 57 | S&F in repairs for 125mm dia Steelness steel grating doom with waste hole for waste pipe (minimum weight 40 gram) complete all as specified and directed by Engr In Charge. |
| 58 | S&F in repairs 15mm CP bib tap fancy type copper alloy with crutch or butterfly handle , screwed down, screwed for iron pipe etc complete all as specified and directed by Engr In Charge. |
| 59 | S&F in repairs chromium plated shower rose 125 mm size with or without swivel joints complete all as specified and directed by Engr In Charge. |
| 60 | M&L in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cemen complete all as specified and directed by Engr In Charge. |
| 61 | S&F in repair CP stop valve /angle valves, cast copper alloy, fancy type, chromium plated with long shank & cup (concealed type) with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore complete all as specified and directed by Engr-In-Charge. |
| 62 | S&F in repairs CP tubular Towel rail , 20 mm dia, D Type 600mm long between flanges brass chromium plated with screws and cleats, (Minimum weight 190 gms) complete all as specified and directed by Engr In Charge. |
| 63 | S&F in repairs soap dish / Paper Holder Steelness steel fixed to plugs with chromium plated brass screws etc complete all as specified and directed by Engr In Charge complete all as specified and directed by Engr In Charge. |
| 64 | S&F 15mm dia PVC Connection 450 mm long with nuts complete all as specified and directed by Engr In Charge. |
| 65 | S&F in repairs vitreous china wash hand basin bowl type of size 550mm x 400mm white, flat back including angle iron brackets including PVC waste pipe of 32mm dia of suitable length, and 32mm dia brass waste fitting complete all as specified complete all as specified and directed by Engr In Charge. |
| 66 | S&Fin repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engr In Charge. |
| 67 | S&F in repair glass shelf assembly consisting of 5.5 mm thick sheets glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-In-Charge. |
| 68 | S&F in repair corner glass shelf with bracket complete all as specified and directed by Engineer-in-charge. |
| 69 | S&F in repairs fancy type 15mm dia Brass CP wall mixer/basin hole mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed by Engineer-in-charge. |
| 70 | S&F in repairs 32mm dia Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified and directed by Engr In Charge. |
| 71 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc complete all as specified and as directed by the Engineer-in-Charge. |
| 72 | M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge. |
| 73 | M&L Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed by Engr In Charge. |
| 74 | Demolition of concrete surfaces in ground floor and paving n.exc. 15cm thickness (below or above ground level) all as Specified. |
| 75 | M & L for 75 mm thick PCC 1:3:6 type C2 as in Plinth Protection using 40 mm stone aggregate including making joints & filling with sand bitumen mastic as per complete all as specified and directed by Engr In Charge. |
| 76 | Demolition reinforced cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas, RCC Jali and similar suspended work (reinforcement cut as required to facilitate demolition) complete up to nine storey height building all as specified and directed by Engineer-in-Charge. |
| 77 | M&L Reinforced cement concrete nominal mix 1:2:4, type B-1 using (20mm graded aggreate) in slabs supported on walls, beams and column in floors,roofs,landings, balconies, canopies, deck slabs and in shelves and the like complete including formwork all as specified and directed by Engr-In-Charge. |
| 78 | S& F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire(annealed) not less than 0.9mm dia upto nine storey complete all as specified and directed by Engr In Charge. |
| 79 | Removing plant including roots by dismantaling of brick work PCC/RCC including necessary scaffoilding any type in any location/position i.e roof , parapet wall near pipes etc and applying acid after removing roots for preventing the regrowth and making good of disturbed portion using PCC 1:2:4 type B0 & 10mm thick plaster in CM 1:3 size of disturbed portion 150 x 150 x 200mm complete up to nine storey height building all as specified & directed by Engr - In - Charge. |
| 80 | Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 and portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc. |
| 81 | S&F Mild steel, plain black sheet 1.00mm thick in wall cladding, steel gates & similar work, cut to size, holes punched; including round headed screws, clout nails or rivets & fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required |
| 82 | M&L for preparation of new steel surfaces of any description, not other wise described, over 10 cm width or girth and applying two coats synthetic enamel paint over a coats of red oxide primer as specified and directed by Engr-in-charge. |
| 83 | M&L for removing building materials etc. (other than spoil payable under items 03028 to 03031 in Section-3—Earthwork) to a distance of 15km, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and directed by Engineer-in-Charge. |
| 84 | S&F in repair for plain galvanized sheet 0.8 mm thick and 300 mm wide to covering of crumple/expansion joint/gaps on vertical/horizontal surface, steeped finishind or fixing screw up to nine storey height building etc complete all as specified and directed by Engr In Charge. |
| 85 | S&F in repair for plain galvanized sheet 0.8 mm thick and 450 mm wide to covering of crumple/expansion joint/gaps on vertical/horizontal surface, steeped finishind or fixing screw up to nine storey height building etc complete all as specified and directed by Engr In Charge. |
| 86 | S&F in repair for plain galvanized sheet 0.8 mm thick and 1000 mm wide to covering of crumple/expansion joint/gaps on vertical/horizontal surface, steeped finishind or fixing screw up to nine storey height building etc complete all as specified and directed by Engr In Charge. |
| 87 | S&F precast machine pressed PCC interlocking paver block of 80 mm thickness, M-40 grade of any shape and size confirming to IS -15658-2006 with grey cement and pigment as approved and 80mm thick plain cement concrete, type D-2, 1:4:8, (using 40mm graded stone aggregate) as in sub base flooring, and dismantling old tiles complete all as specified and directed by Engineer-in-Charge. |
| 88 | Taking down carefully copper/aluminium point wiring light, fan, light fittings, socket or power complete, such as switches, ceiling roses, pendants, regulators, sockets etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditioned separately) and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engineer-in-Charge Please Enable Macros to View BoQ information |
| 89 | Taking down carefully copper/aluminium point wiring light, fan, light fittings, socket or power complete, such as switches, ceiling roses, pendants, regulators, sockets etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditioned separately) and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engineer-in-Charge Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Aug 12, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Jul 16, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Completed
Jul 23, 2026
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Completed
Jul 30, 2026
18:00 IST
Corrigendum-3 Issued
Clarifications on tender conditions and amendments issued.
Completed
Aug 03, 2026
18:00 IST
Corrigendum-4 Issued
Clarifications on tender conditions and amendments issued.
Completed
Aug 03, 2026
18:00 IST
Corrigendum-5 Issued
Clarifications on tender conditions and amendments issued.
Completed
Aug 10, 2026
18:00 IST
Corrigendum-6 Issued
Clarifications on tender conditions and amendments issued.
Completed
Aug 17, 2026
18:00 IST
Corrigendum-7 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 2 daysAug 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysAug 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender