|
| 1 | Boring of 30cm dia piles of single under reamed of 50cm dia of bulb and 3.5 meter depth in black cotton soil with hand operated auger machine including all laboure T&P etc. for proper completion of work as per IS code-2911(Part-III) 1980. |
| 2 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:(All kinds of soil)As per DSR-2.1.1 |
| 3 | Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete.As per DSR-2.27 |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).As per DSR-4.1.8 |
| 5 | Providing and injecting chemical emulsion for pre-constructional antitermite treatment and creating and chamical bariier under and arround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the external perimeter of binding expansion joints, surrounding of pipes and conduit etc. complete (plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981) approved material such as Hepthachlor or chlordane will be used. The rate of application of chemical emulsion shall be as follows. |
| 6 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) :.As per DSR-5.2.2 |
| 7 | Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in foundation and plinth Cement morter 1:4 .As DSR NO.- 6.1.1 |
| 8 | Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5 in Superstrecture and above plinth Cement morter 1:6 .As DSR NO.- 6.4.2 |
| 9 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars.As per DSR-5.22.1 |
| 10 | CEMENT PLASTER (IN FINE SAND)12 mm cement plaster of mix :in 1:4 (1 cement: 4 fine sand).AS per DSR No.- 13.1.1 |
| 11 | 4 cm thick cement concrete floor 1:2:4 finished with a floating coat of neat cement including cement slurry,but excluding cost of nosing of steps etc all complete.As per DSR no.- 11.3.1 |
| 12 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Glazed vitrified floor tile polished finish of size of tile 600 x 1200 mm .As per DSR No.- 11.41A.2.2 |
| 13 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 14 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 15 | supply & Fixing of 10cm Internal dia PVC pipes complete with rose- heads, bends abd gratings & including supply of necessary M.S. clamps 2.5cmx3mm (1\\"x1/8\\") fixed to walls, with & including supply of 15cm (6\\") long 6mm (1?4\\") dia nails & including supply of all materials, labour and T&P etc required for proper completion of the work and also including repair of plaster, pointing etc if damaged during fixing of pipes, details of 30' length. |
| 16 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.As Per DSR No.8.2.2.1 |
| 17 | Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.As per DSR No.- 10.1 |
| 18 | Supply & fixing of flush doors commercial quality conforming to IS 2202 Part 1 (1983) including fixing of wooden cleats and stoppers and including fixing and adjustment of hinges bolts locks handles springs fitting with necessary screws to be supplied departmentally. (a) Single leaf (35 mm Thick). As per DSR No. - 9.20.1 |
| 19 | Painting or varnishing new iron work in small areas of new wood of 1 sqm area with one coat of ready mixed priming paint and two coat or approved superior quality ready mixed paint or varnish including supply of all material, labour and T&P etc. required .AS per SOR |
| 20 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. As per DSR No.-17.1.1 |
| 21 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid As per DSR No.-17.3.1 |
| 22 | White Vitreous China Surgeon type wash basin of size 660x460 mm with single 15 mm C.P. brass pillar taps with elbow operated levers ISI Marked. As per DSR No.- 17.7.9 |
| 23 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(25 mm nominal dia Pipes).Asper DSR No.-18.7.3 |
| 24 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(15 mm nominal dia Pipes).Asper DSR No.-18.7.1 |
| 25 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore. As per DSR No.- 18.17.1 |
| 26 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore.As per DSR No.- 18.51.1 |
| 27 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.As per DSR No.- 18.52.1 |
| 28 | Supply & wiring of sub-main with 2 nos 2.5 sqm FR P.V.C. insulated 1100 volts grade multistand single core copper conductor cable in 20 mm diameter heavy duty 2mm thick P V C conduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete .As per E&M DSR no.- 1.14.2 |
| 29 | Supply & wiring of sub-main with 2 nos 4 sqm FR P.V.C. insulated 1100 volts grade multistand single core copper conductor cable in 20 mm diameter heavy duty 2mm thick P V C conduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete .As per E&M DSR no.- 1.14.2 |
| 30 | Supply and erection of AC 230/250 Volts 50 Hz Exhaust fan including providing nuts bolts amounting frame & other accessories including connection etc. complete as required (Crompton Greaves/ GEC / Orient or equivalevt mark)(a) - 300 mm Sweep As per market |
| 31 | Wiring point for light /fan /exhaust fan with 1.5 sq.mm FR P.V.C insulated multistrand single core copper cunductor cable in P V C cond-uit pipe part cocealed in wall & partly laid in slabalong with the reinforcement before concreting complete with 14 S.W.G. copper earth continuity wire & piano type switch and ceiling rose/angle/batten holder on 3mm thick phenolic laminated backelite sheet etc. complete in all respect.including matching color wash.As per DSR no.-1.1.1 |
| 32 | Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect.CAT- AAA |
| 33 | Supply & fixing of 5/6/7.5/10/15/20/25/30/32 Amp SPMCB 9 KA/10 KA |
| 34 | Supply and fixing of flush/surface mounting distribution boards without MCB with additional metal door complete in all respects.(CAT:B)8 Way SPN |
| 35 | Supply fixing and making connection of following FPMCBS complete in all respects as per direction and satisfaction of engineer- in-charge.40 Amp. DP MCB |
| 36 | Supply and burying of 40mm dia x 4.5meters long G.I. pipe, vertically for earthing having 12 mm dia. Holes spaced 75mm apart drilled upto 2 meters from the bottom complete with earthing lead of no 6 to 8 SWG GI wire in GI pipe upto appron (and from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) upto switch board, 30cm. square C.I. box with hinged cover, masonary enclosue, funnel at top, alternate layers/of charcoal/ coke and salt at least 150mm thick alround etc. complete in all respects. |
| 37 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.As per DSR No.- 17.16 A |
| 38 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.As per DSR No.- 17.22 |
| 39 | Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. DSR No.- 17.22A |
| 40 | Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. DSR No.- 17.24 |
| 41 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.As per DSR- 18.48 |
| 42 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.). DSR - 10.28 |
| 43 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mmDSR - 17.32.4 Please Enable Macros to View BoQ information |
