|
| 1 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specially provided including removal of debris outside MD land complete all as specified and directed by EIC. |
| 2 | Dismantling wrought iron or mild steel work of any description not otherwise provided for |
| 3 | Dismantling fencing wire , any type |
| 4 | M&L for Providing, cement concrete Type B-1 1:2:4 (20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, bed blocks, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork as specified and directed. |
| 5 | M&L for Rolled sections as in framing for cladding, struts, posts, glazing and the like fixed with angle cleats and connecting plates, etc.Fe 410-W (GdeE- 250) quality A |
| 6 | M&L for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) |
| 7 | S&F barbed razor tape concertina coil SG hot galvanized spring tensile wire to particular here-in-after or other equivalent make as approved by GE of UTS 145 to 150kg/mm^2 and dia of coil when unstretched 601mm having minimum number of circles 10/Rm,minimum number of clips 25/Rm and minimum weight of coil 1.625 Kg/Rm, hot dip galvanized razor ribbon tape of size 0.50mm thickness , 19mmm width before wrapping on central core wire fixed with GI 1.66mm clips and special nut bolts to hold two coils together and extra two rows parallel wire of 10 gauge tied by binding wire wherever complete all as specified and directed by EIC. |
| 8 | M&L applying two coats of synthetic enamel paint over a coat of red oxide on new steel surfaces over 10cm width or girth including preparation of surface complete all as specified and directed. |
| 9 | M&L for Broken glass coping on top of walls in CM 1:3 including Taking and removing rubbish complete all as specified and directed. |
| 10 | Removing debris exc. 5 km but n exc. 15 km and depositing where directed |
| 11 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and not exceeding 10 sqm on plan and getting out in soft/loose soil for laying of cables, etc. complete all as specified and as directed. |
| 12 | Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm deep as in hard/soft soil complete all as specified and as directed. |
| 13 | Removing excavated materials to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point in soil including spreading in low lying area and leveling complete all as specified and as directed. |
| 14 | M&L for cutting existing road/hard standing not exceeding 45x50 cm in wide & depth getting out excavated material for laying GI tube, returning filling & well rammaing watering finish suraface 10 cm from top including provision of PCC 1:3:6 for repairing, including removal of surplus soil all as directed. |
| 15 | Removing, taking out, dismantling, cutting and lowering down existing pipes of any type and material (GI/MS/steel/DI/CI/PVC/HDPE etc.) of 25 mm diameter, in any condition, from any position, location and level including underground, inside buildings, shafts, trenches, ceilings, walls or open areas, including breaking of joints, necessary staging/scaffolding, handling, loading, unloading, stacking at designated place or disposal as directed, complete with all labour, tools, tackles, safety measures and incidentals, complete all as specified and as directed by the Engineer-in-Charge. |
| 16 | Ditto all as per item No 15 above but 40 mm dia bore complete |
| 17 | Ditto all as per item No 15 above but 50 mm dia bore complete |
| 18 | Ditto all as per item No 15 above but 80 mm dia bore complete |
| 19 | Ditto all as per item No 15 above but 100 mm dia bore complete |
| 20 | Ditto all as per item No 15 above but 150 mm dia bore complete |
| 21 | Supply, laying, fixing, jointing, connecting and testing in repairs steel water tubing, medium grade, galvanised, ISI marked, with screwed and socketed joints, in any length, including supply and fixing of all required fittings such as elbows, tees, bends, unions, sockets, nipples, clamps, etc., fixed to walls or laid in trenches, floors or any other position, including cutting, threading, making good the disturbed surfaces, testing to required pressure, complete for 25 mm bore, all as specified and as directed by the Engineer-in-Charge.Make: Tata / Jindal |
| 22 | Ditto all as per item No 21 above but 40 mm dia bore complete |
| 23 | Ditto all as per item No 21 above but 50 mm dia bore complete |
| 24 | Ditto all as per item No 21 above but 80 mm dia bore complete |
| 25 | Ditto all as per item No 21 above but 100 mm dia bore complete |
| 26 | Ditto all as per item No 21 above but 150 mm dia bore complete |
| 27 | S&F sluice valve 150 mm bore, cast iron body, flanged drilled end, conforming to IS-14846, ISI marked, class PN 1.6, resilient seating as well as metal seating Fusion bonded epoxy coating including all joints with rubber gaskets, bolts and nuts, washers, iron wheel including taking up / down old unserviceable valves from any position and any addition / alteration for fixing required complete all as specified and as directed. Make :- Kirloskar / Leader / Kartar / Upadhyay |
| 28 | Ditto all as per item No 27 above but 100 mm dia bore complete |
| 29 | Ditto all as per item No 27 above but 80 mm dia bore complete |
| 30 | S&F in repairs gunmetal gate or globe valve for 50 mm diameter, conforming to IS-778, Class 2, ISI marked, Copper alloy body, Test pressure (Hydrostatic) for shell 2.4 Mpa and Seat & back seat pressure of about 1.6 Mpa with maximum working temperature of about 45 °C with iron wheel head screwed at both ends for iron pipes or ferrule and fixing including necessary fittings like unions, check nuts, etc and any addition / alteration required for fixing, complete all as specified and as directed. Make :- Leader / Zoloto / L&T / Sant |
| 31 | -Ditto- all as per Item No 30.00 above but of size 40 mm dia |
| 32 | -Ditto- all as per Item No 30.00 above but of size 25 mm dia |
| 33 | Supply, installation, testing and commissioning of 100mm Cast Iron Non-Return Valve, PN-1.6 Swing Type, with nitrile rubber flap disc, cast iron body, bolted cover, flanged ends conforming to IS:1538, complete with gaskets, fasteners and necessary accessories, installed at any position and any addition / alteration for fixing required complete all as specified and as directed by Engr- in - Charge. Make : L&T / Castle / Leader / Zoloto |
| 34 | S & F cast iron Foot valve 80 mm, Ball type with flange joint model B-05 (N) conforming to IS with MS nuts bolts, washer, rubber gasket etc., any pattern as approved including any position and any addition / alteration for fixing required with testing complete all as specified and as directed by Engr- in - Charge.Make : Kirloskar / Kartar / Leader / Sant |
| 35 | Supply and fixing brass Air release valve of size 20 mm dia including all necessary fittings required for fixing complete all as specified and directed by Engr- in - Charge. Make :- Kirloskar / Leader / Castle / Anergy / Zoloto |
| 36 | Supply and fix Pressure gauge of 4\\" dial 0-14 kgs rating with ball valve including taking up / down old unserviceable pressure gauge from any position and any addition / alteration for fixing required complete all as specified and as directed by Engr- in - Charge. Make: Fiebig/ H. Guru/ Baker Mercer/ Danfoss |
| 37 | Material and labour for Welding in repairs exc 2.5 cm but not exc 5 cm in length, thickness of Metal to be welded exc 6mm but not exc 9 mm complete all as specified and directed. |
| 38 | Material and labour for cutting/drilling of existing DI/Cast Iron water main and tapping in position for providing branch connection of required internal diameter, including necessary tools, fittings, jointing, testing and making good, complete all as specified and as directed. |
| 39 | Supply and fixing in repair of 25 mm bore PVC ball valve, ISI marked, high-pressure type, made of PTMT, with epoxy-coated aluminium rod and high-density plastic ball, screwed type suitable for iron pipe, including all necessary fittings, fixing and testing, including taking down the existing unserviceable float valve, complete all as specified and as directed.Make: Prayag / Shakti. |
| 40 | Supply, laying and testing of 20 mm outer dia, 3- layer PP-R (Polypropylene random copolymer) pipes SDR 7.4/PN 16 UV stablised and antimicrobial fusion welded having thermal stability for portable water supply all PP-R plain & brass threaded polypropylene random including all fittings such as bends, tees, elbows, reducers, unions, plugs, sockets, GI–PPR transition fittings etc laid in trenches/floors, complete all as specified and directed . Make:-Prince /Supreme |
| 41 | Ditto all as per item No 40 above but 25 mm dia bore complete |
| 42 | Ditto all as per item No 40 above but 40 mm dia bore complete |
| 43 | Ditto all as per item No 40 above but 50 mm dia bore complete |
| 44 | S & F in repair PP-R Gate valve (Brass insert) 3 layered (outer green coloured UV stabalized , middle black coloured UV stabalized, and inner most layer white coloured with antimicrobial property )fusion welded PP-R ( Polypropyelene random copolymer) gate valve brass 20 mm Outer dia light weight ISI marked as per pre requirement of the site with handle screwed both ends for PP-R Pipes or for unions fixed of grade PN-25 , SDR-7.4 complete all as specified and as directed . Make:-Prince /Supreme |
| 45 | All as per Item No. 44 but for 25 mm outer dia pipe |
| 46 | All as per Item No. 44 but for 40 mm outer dia pipe |
| 47 | All as per Item No. 44 but for 50 mm outer dia pipe |
| 48 | M&L for renewal of valve pit of size up to 80 cm x 80 cm x 80 cm (internal diamension), stone / brick construction including all necessary excavation and earth work in any type of soil, returning, filling in disposal of surplus soil to a distance not exceeding 50 m and depositing where directed, PCC in foundation for mix (1:2:4) type D2 brick mansonary in cement mortar (1:4) rendering 12 mm duck in cement mortar (1:4) internally ,finished even and fair and polishing flush externally as the work proceeds in the same mortor. Mild steel angle iron 40 x 40 x 6 mm frame MS sheet cover 3.15 mm thick with handle and locking arrangement, painting all exposed MS work with two coats of synthetic enamel paint of the that as approved by the Engineer - in - charge over a coat of red oxide primer and painting all the MS embeded in PCC with two coats of black bitumenous paint complete all as specified. Please Enable Macros to View BoQ information |
| 49 | M&L for renewal of valve pit of size up to 80 cm x 80 cm x 80 cm (internal diamension), stone / brick construction including all necessary excavation and earth work in any type of soil, returning, filling in disposal of surplus soil to a distance not exceeding 50 m and depositing where directed, PCC in foundation for mix (1:2:4) type D2 brick mansonary in cement mortar (1:4) rendering 12 mm duck in cement mortar (1:4) internally ,finished even and fair and polishing flush externally as the work proceeds in the same mortor. Mild steel angle iron 40 x 40 x 6 mm frame MS sheet cover 3.15 mm thick with handle and locking arrangement, painting all exposed MS work with two coats of synthetic enamel paint of the that as approved by the Engineer - in - charge over a coat of red oxide primer and painting all the MS embeded in PCC with two coats of black bitumenous paint complete all as specified. Please Enable Macros to View BoQ information |
