|
| 1 | Part A |
| 2 | SITC of Automatic Lift (as per manufacturer design & as per detailed specification below conforming to IS) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor if any etc to complete as reqd. |
| 3 | .Make : OTIS / KONE/SCHINDLER |
| 4 | Type: Bed cum Passenger Lift . |
| 5 | Load: 20 Passenger / 1360 Kg |
| 6 | Control- Microprocessor based with AC variablevoltage & variable frequency ( VVVF) |
| 7 | Machine:- Energy efficient machine, Gearless, with out Machine Room |
| 8 | Position of Machine Room: - Not applicable |
| 9 | Speed: 1.0 Mtrs./ Sec |
| 10 | Floor served : G+7 |
| 11 | Landing:- 8, all on same side |
| 12 | Total Rise : 31.6 Mtr |
| 13 | Operation- Microprocessor based simplex full collective with or without attendant. |
| 14 | Signals Digital car position indicator,car travelsdirection indicator in car & at all landing with callregistration indicator. |
| 15 | Leveling accuracy: +- 5 mm(Micro levelling arrangement) |
| 16 | Car inside: 1300 mm ( W ) x 2400 mm ( D ) X 2200 MM HIGH |
| 17 | Car Entrance : Minimum Clear Opening 1000 mm (W) x 2000 mm (H ) protected with car door |
| 18 | Car Enclosure : Stainless Steel sheet (20 SWG) with Hairline finish with hand rail. |
| 19 | Car Ceiling & Lighting: Stainless Steel with hairline finish with I ED lighting and Fan |
| 20 | Car Ventilation: Pressure fan with anodized aluminium grill. |
| 21 | Car Flooring: Decorative granite fiooring (As per direcion of EIC and according to this Department's Order). |
| 22 | Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system |
| 23 | Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system |
| 24 | Door Opening: Automatic power oprated door with full length PhotoccH assembly light curtain sensor |
| 25 | PROTECTIVE DEVICES & OTHERACESSORIES |
| 26 | ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others. |
| 27 | Overload Protection: Fully loaded with overload protection. On overloading the lift car will not start with door remaining open and give audio display indication |
| 28 | Emergency lighting in car : Battery operated emergency lighting in the lift car. |
| 29 | Intercom system : Battery operated intercom system in Lift Car, Machine Room & Control Room |
| 30 | Emergency Alarm: Battery operated alarm bell system in lift car and control room |
| 31 | Fireman switch : Fireman switch at main landing terminal. |
| 32 | Voice Synthesizer : Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator. |
| 33 | Main rope : As per manufacturer's standard conforming to IS |
| 34 | DIMENSION OF SHAFT & POWER SUPPLY |
| 35 | Available Shaft Dimension : 2174 mm X 2900 mm |
| 36 | Pit Depth : 1800 mm |
| 37 | Overhead: 4500 mm |
| 38 | Electric power supply : AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS |
| 39 | Bidder should see the actual physical well size and no extra cost will be paid for additional fabrication of angle iron structure , iron clamp or any other mechanical works . Rates should be quoted with minor civil work ( i.e. chieseling inside the lift well , necessary pocket cutting , making hole on machine room floor etc. incl mending good the damages should be made by the respective agency. |
| 40 | Part B |
| 41 | SITC of Automatic Lift (as per manufacturer design & as per detailed specification below conforming to IS) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor if any etc to complete as reqd. |
| 42 | .Make : OTIS / KONE/SCHINDLER |
| 43 | Type: Bed cum Passenger Lift . |
| 44 | Load: 10 Passenger / 680 Kg |
| 45 | Control- Microprocessor based with AC variablevoltage & variable frequency ( VVVF) |
| 46 | Machine:- Energy efficient machine, Gearless, with out Machine Room |
| 47 | Position of Machine Room: - Not applicable |
| 48 | Speed: 1.0 Mtrs./ Sec |
| 49 | Floor served : G+7 |
| 50 | Landing:- 8, all on same side |
| 51 | Total Rise : 31.6 Mtr |
| 52 | Operation- Microprocessor based simplex full collective with or without attendant. |
| 53 | Signals Digital car position indicator,car travelsdirection indicator in car & at all landing with callregistration indicator. |
| 54 | Leveling accuracy: +- 5 mm(Micro levelling arrangement) |
| 55 | Car inside: 1200 mm ( W ) x 1400 mm ( D ) X 2200 MM HIGH |
| 56 | Car Entrance : Minimum Clear Opening 800 mm (W) x 2000 mm (H ) protected with car door |
| 57 | Car Enclosure : Stainless Steel sheet (20 SWG) with Hairline finish with hand rail. |
| 58 | Car Ceiling & Lighting: Stainless Steel with hairline finish with I ED lighting and Fan |
| 59 | Car Ventilation: Pressure fan with anodized aluminium grill. |
| 60 | Car Flooring: Decorative granite fiooring (As per direcion of EIC and according to this Department's Order). |
| 61 | Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system |
| 62 | Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system |
| 63 | Door Opening: Automatic power oprated door with full length PhotoccH assembly light curtain sensor |
| 64 | PROTECTIVE DEVICES & OTHERACESSORIES |
| 65 | ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others. |
| 66 | Overload Protection: Fully loaded with overload protection. On overloading the lift car will not start with door remaining open and give audio display indication |
| 67 | Emergency lighting in car : Battery operated emergency lighting in the lift car. |
| 68 | Intercom system : Battery operated intercom system in Lift Car, Machine Room & Control Room |
| 69 | Emergency Alarm: Battery operated alarm bell system in lift car and control room |
| 70 | Fireman switch : Fireman switch at main landing terminal. |
| 71 | Voice Synthesizer : Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator. |
| 72 | Main rope : As per manufacturer's standard conforming to IS |
| 73 | DIMENSION OF SHAFT & POWER SUPPLY |
| 74 | Available Shaft Dimension : 1900 mm X 2100 mm |
| 75 | Pit Depth : 1800 mm |
| 76 | Overhead: 4500 mm |
| 77 | Electric power supply : AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS |
| 78 | Bidder should see the actual physical well size and no extra cost will be paid for additional fabrication of angle iron structure , iron clamp or any other mechanical works . Rates should be quoted with minor civil work ( i.e. chieseling inside the lift well , necessary pocket cutting , making hole on machine room floor etc. incl mending good the damages should be made by the respective agency. Please Enable Macros to View BoQ information |
