|
| 1 | EARTH WORK IN FOUNDATION TRENCHES:Excavation work by mechanical means (Hydraulic Excavator) manual means in foundation trenches or drains not exceeding 1.5 m in width or 10 sqm on plan including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m. |
| 2 | Providing and laying hand packed stone soling in buildings works with clean hard selected stones, all complete. (Manual). |
| 3 | Providing and Laying in position cement concrete of specified grade including compacting curing etc all complete. 1:2:4 mix. (1cement, 2coarse sand, 4 graded stone aggregate of 20mm & down size). |
| 4 | Providing and Laying Random Rubble Stone Masonry in1:3:6 c.c.(1 cement, 3 sand, 6 clean hard graded stone chips, size 40 mm gauge) including bond stone, through stone of size 15 0mm x 150 mm x 450 mm manufactured in 1:4:8 (1 cement, 4 clean coarse sand, 8 clean hard stone aggregate of size 40mm and down) and curing etc, complete as per the direction of Engineer in Charge, excluding the cost of carriage of materials. |
| 5 | Steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 6 | Providing and Fixing G.I. Chain Link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. |
| 7 | Providing and Laying in position specified grade of reinforced cement concrete excluding the cost of form work, finishing and reinforcements.1:1.5:3 Mix (1cement, 1.5 coarse sand 3 graded stone aggregate 20mm and down nominal gauge). |
| 8 | Supplying, bending and placing in position tor- steel reinforcement in all R.C.C works including cost of binding wires, all complete. |
| 9 | Supplying, bending and placing in position mild steel (6 mm dia.) including straightening, cutting, bending and placing in position including binding wire complete. |
| 10 | Centering and Shuttering including strutting, proping etc. and removal of form work for: Lintels, Beam, Plinth Beam, Girders, Bressumers and Cantilever. |
| 11 | Centering and Shuttering including strutting, proping etc. and removal of form work for: Foundation, Footing, Bases of Column etc. for mass concrete. |
| 12 | Centering and Shuttering including strutting, proping etc. and removal of form work for: Column, Pillars, Piers, Abutments, Post & Struts. |
| 13 | Providing and laying first class brick work in half brick thick in super structure of standardsize bricks with 1:4 cement mortar (1 cement and 4 course sand) including carriage of bricks upto work site, curing etc all complete. |
| 14 | Providing and Laying 15mm thick cement plaster of specified mix in single coat including finishing even and smooth and curing etc all complete. 1:4 Mix |
| 15 | Providing and Fixing PVC door frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm, including providing EPDM rubber gasket weather seal throughout the frame including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x 100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer-in-charge. |
| 16 | 35 mm thick factory made solid panel PVC door shutter, made out of single piece extruded solid PVC profile, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mm x 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm x 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent, self driven self tapping screws & MS rectangular pipes bracket of size 190 mm x 100 mm of cross section size 35 mm x 17 mm x 1 mm at each coener. Single piece extruded 5 mm thick solid PVC lock rail pf size 115 mm x 35 mm, outb of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacture's specification and direction of Engineer-in-Charge. Decorative finish (wood grained finish). |
| 17 | Providing and Laying white or colored glazed tiles anti skid (elegant, cashmere, Egyptian rustic, celebrity, lara etc or equivalent) of glossy series or celebrity, elegant or equivalent in flooring, treads of steps landing etc of size 300mm x 300mm laid on a bed of 15mm, cm 1:3 (1cement, 3coarse sand) finished with flush pointing with white cement slurry. |
| 18 | Providing and Laying white or colored or ceramic glazed tiles of size 200mm x 300mm luster printed (loreno, bronzo,colubia or equivalent) in skirting, risers of steps and Dados on 12mm thick cement plaster (1cement, 3coarsed sand) 1:3 bare and jointed with white cement slurry. |
| 19 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 20 | Providing, fitting, fixing of 24 BWG Pre‐painted HULAS sheet roofing with lapping of 150mm (two corrugation) with G.I. hooks, bolts and nut 8mm dia with bitumen, GI limpet washers filled with white bad including carriage all complete |
| 21 | Providing fitting fixing ridges or hips of 60 cm over all width of plain 24 BWG Pre‐painted HULAS Sheet fixed with G.I, J or L hooks bolts and nuts 8 mm dia Limpets, Bitumen washers complete. |
| 22 | Providing and laying plaster of paris putty of 2mm thick over plastered surface to prepare the surface even and smooth all complete: |
| 23 | Providing and painting with ready mixed Enamel paints of approved quality and shade with two or more coats to give an even and smooth shade including clearing the surface complete on new surface. |
| 24 | Providing and Providing and painting with acrylic exterior paints of quality and make equivalent to EXCEL, WEATHER SHIELD to give an even shade including brushing the surface clean of dirt, dust etc. and sand papering and filling the scratches complete on New surface. |
| 25 | Distempering with dry distemper on New surface two or more coats of required shade to give an even and uniform shade including priming coat of whiting to give an even shade after thorough cleaning of dirt, dust, loose pieces of scabs, grease etc including surface preparation by sand paper in get ccomplete.New surfac |
| 26 | Providing and Providing and painting with plastic Emulsion paints on eormore coats on old surface of required shade to give even shade in‐including brushing the surface clean of all dirt, dust and smoothened by sand paper etc complete. |
| 27 | Providing, fitting and fixing white vitreous china flat back or wall corner type lipped front urinal basin of size 440x315x325 mm with 5ltr automatic flushing cistern with C.I. brackets, GI flush pipe and spreaders with brass unions and G.I. clamps including cutting and making good the walls and floors as required all complete: Range of 1 Urinal basin. |
| 28 | Providing, fitting and fixing white vitreous white china wash flat back basin with CI brackets, painted, 15 mm CP brass pillar taps, CP brass chain with rubber plug, 32 mm CP brass waste pipe, lead or PVC connection 32 mm dia CP brass cap andunions, complete including cutting and making good the walls wherever required. HINDWARE. One wash basin with one pillar cock. (63 cm x 45 cm). |
| 29 | Providing and Fitting Pedestal white colour for of Hind Vitreous wash basin complete. |
| 30 | Providing, fitting and fixing. urinal single squatting plate of white glazed fire clay with integral flushing pipe, 100mm channel,automatic flushing cistern of 5 liter.C.I.brackets, G.I. flush pipe with spreader pipe with fitting, G.I.clamps C.I.urinal trap 65 mm channel with vent including cutting and making good the wall and floors as required. Single squatting plate with 5 Ltr. cistern. |
| 31 | Providing, fitting and fixing Beveled gauge mirror of superior glass with 6mm A.C. sheets ground and fixed to timber cleats with CP screws, washer etc complete. |
| 32 | Providing, Fitting and fixing GI pipe of medium class, (excluding trenching, refilling, compacting and the cost of fittings) all complete.(15 mm dia G I pipe ) |
| 33 | Providing, fitting and fixing soil, waste and vent pipes including testing etc complete:100 mm dia. PRINCE / SUPREME or equivalent soil pipe |
| 34 | Providing, fitting and fixing bends of various types plain or a band with access door, insertion rubber washer 3mm thick bolts and nuts complete SCI or centrifugally cost spun sands pipes:100 mm dia. Supreme / Prince. |
| 35 | Providing, fitting and fixing double equal junction of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete:100 x 100 x 100 x 100 mm Supreme / Prince. |
| 36 | Providing & Fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000x450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge. |
| 37 | Supplying and Fixing Rolling Shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specialy designed pipe shaft with brackets, side guides and arrangments for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS: 4454-part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover. |
| 38 | Extra for providing mechanical device chain and crank operation for operating rolling shutters.Exceeding 10.00 sqm and upto 16.80 sqm in the area. |
| 39 | Fixed window/ventilator made of (small series) frame 47x50 mm & mullion 47x68 mm both having wall thickness of 1.9± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 40 | Providing, fitting and fixing towel rail of chromium plated brass complete with brackets fixed to the timber cleats, CP brass screws complete.600 x 20 mm. |
| 41 | Providing and Fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6 mm for diagonal braces and central cross piece. |
| 42 | Providing and Laying Chequers tiles inonf looring over12mm thick cement plaster (1 cement, 3 coarsed sand) 1:3 bare and jointed with white cement slurry. |
| 43 | Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing andTechnical specifications. Stone/Boulder. |
| 44 | Providing and fixing to existing door shutter 30 mm thick Glass Fibre Reinforced Polyester (FRP) Flush door shutter of required colour and approved brand and manufacture, made with fireretardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used as filler material throughout the hollow panel, cast monolithically with testing parameters of F.R.P. laminate conforming to table ‐ 3 of IS:14856:2000 complete as per direction of Engineer‐in‐charge of seasoned wood inside at required placed for fixing and fittings. |
| 45 | Providing and Fixing Brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 46 | Providing and Fixing Hydraulic door closer with accessories and screws complete. |
| 47 | Tubular Steel Railing on Medium Weight steel channel (ISMC series) 100 mm x 50 mm (Providing, fixing and erecting 50 mm dia steel pipe railing in 3 rows duly painted on medium weight steel channels (ISMC series) 100 mm x 50mm, 1.2 metres high above ground, 2m centre to centre, complete as per approved drawings. |
| 48 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 49 | Providing and Fixing 12 mm thick frameless toughned glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-Charge (Door handle, lock and stopper etc. to be paid separately). |
| 50 | Providing and Fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-Charge. Polyester powder coated minimum thickness 50 micron aluminium. |
| 51 | Loading and unloading of stone boulder/stone/aggregates/sand/ kanker/moorum. |
| 52 | Loading and Unloading of Cement or Steel by Manual Means and stacking. |
| 53 | Cost of haulage excluding loading and unloading- Surfaced road:-Non-stock & stock materials Please Enable Macros to View BoQ information |
