|
| 1 | Earthwork in Hard soil within 50m, initial lead , 1.50m initial lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3m in depth and as per direction of the Engineer in charge. |
| 2 | Loosening of the ground upto a level of 500 mm below the sub grade level, watered, graded and compacted in layers to meet requirements of table 300 - 2 for sub grade construction & clause 305 of MoSRT&H specifications for road & bridge works(4th revision). |
| 3 | Construction of granular sub-base by providing Close graded Granular subbase Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (4th Revision) |
| 4 | Providing, laying, spreading & compacting graded stone aggregate to Wet Mix Macadam specification including pre mixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, laying in uniform layers with paver in sub base/base course on well prepared surface & compacting with vibratory roller to acieve the desired density as per clause 406 of MoSRT & H specifications for road & bridge works.(4th Revision) |
| 5 | Providing and applying Primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surfaces and spraying primer @ 0.60kg/ sqm using Mechanical means as per clause 502 of MoSRT&H Specifications of Road & Bridge work (04th Revision) |
| 6 | Providing and applying Tack coat with bitumen emulsion on prepared surface including clearing of road surfaces and spraying primer @ 0.20kg/ sqm using Mechanical means as per clause 502 of MoSRT&H Specifications of Road & Bridge work (04th Revision) |
| 7 | Providing & laying Bituminous Macadam with hot mix plant using crushed aggregates of specified grading premixed with bituminous binder of 60/70 penetration grade of bitumen, transported to site, laid over previously prepared surface with hydrostatic paver finisher with sensore control to the required grade, level & alingment & roling with smooth wheeled,vibratory & tandem rollers to achieve the desire compaction as per clause 504 of MoSRT&H Specifications for road and bridge works (4th Revision) Page-169 Item -45 |
| 8 | Providing & laying Semi Dense Bituminous Concrete with batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder of 60/70 penetration grade of bitumen, transporting the hot mix to site, laying with a hydrostatic paver finisher with sensore control to the required grade, level & alingment, roling with smooth wheeled,vibratory & tandem rollers to achieve the desire compaction as per clause 508 of MoSRT&H Specifications for road and bridge works (4th Revision) Page -175 item - 47 |
| 9 | Filling sand-Supplying & filling good clean river sand of approved quality including watering to complete saturation & ramming complete with all leads & lifts including cost, conveyance, royalty & taxes of all materials & cost of all labour & T&P required for the work etc. complete as per specification & direction of Engineer in charge. |
| 10 | Providing laying R.C.C. Hume pipe NP3 class for culverts including fixing collar with cement mortar 1:2 but excluding excavation, protection work, backfilling,concrete and masonry work in head walls and parapets clause 1106 of MORD specification for Rural roads and as per irection of Engineer-in charge. |
| 11 | 1000 mm dia Single row |
| 12 | Plain cement concrete M-15 grade in Sub-Structure complete as per drawing and technical specification. |
| 13 | PART-II (BRIDGE PART ) |
| 14 | Earthwork in excavation in cutting in hard soil within the initial lead and lift including rough dressing and breaking clods to maximum 5cm to 7cm andlaying in layers not exceeding 0.3 mtr in depth etc complete as per the direction of the Enngineer in Charge. |
| 15 | Earthwork in excavation in foundation in all kinds of soil within initial lead of 50m. and 1.5m initial lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3 mtr in depth etc complete as per the direction of the Engineer in Charge. |
| 16 | Earthwork in excavation in foundation in hard rock within the initial lead and lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3 mtr in depth etc complete as per the direction of the Enngineer in Charge. |
| 17 | Plain Cement Concrete (1:3:6) using 40mm down graded chips in Foundation and Plinth |
| 18 | Plain Cement Concrete M15 Grade using 40mm down graded chips in Foundation and Plinth |
| 19 | Reinforced Cement Concrete M 25 Grade using 20mm down graded chips in Foundation and Plinth |
| 20 | Railing & Post |
| 21 | Reinforced Cement Concrete M 30 Grade using 20mm down graded chips in superstructure |
| 22 | Deck Slab |
| 23 | Foundation |
| 24 | Abutment & Pier Shaft |
| 25 | Retaining Wall / Wing Wall |
| 26 | (iv) Abutment & pier cap |
| 27 | DIRT Wall |
| 28 | Wearing Coat - Mastic Asphalt & asphalting concrete |
| 29 | Approach Slab |
| 30 | Supply of HYSD bars confirming to grade Fe-500 cutting bending, binding, lapping, splicing, welding etc. (conforming to ISI specification) & jointing if necessary by lapping & tying the grills & placing in position as required for RCC works as per the approved design, hoisting, lowering & laying position including cost & conveyance of tor steel & binding wires of 18 to 20 gauge(as to be approved by the Deptt.) etc. complete (weight of binding wire shall not be considered for payment at all which will be borne by the contractor (standard CO-efficient of different sizes of the steel shall be considered & welding & lapping should confirm to relevant clause of IRC-21/1987) as per clause 1001 of MORD specification for Rural Roads (1st Revision) & as per direction of Engineer-in -Charge. |
| 31 | Providing and laying of Filter media with stone crushed aggregates of 45 mm size satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment , wingwall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specifications. |
| 32 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications. |
| 33 | Rough stone dry packing in aprons and revetments of designed thickness on slope using 30cm and above size hand broken granite stones of approved quality free from weathering skin and from approved quarry including filling the interstices with small stones spalls etc. with cost, conveyance and royalty and with all leads and lifts and taxes of all materials and labour T&P etc complete in all respects (the weight of each stone shall be less than 50kg to 70kg) as per specification and direction of engineer-in-charge & Clause 1300 of MoRD specification for Rural Roads (1st Revision). |
| 34 | Back filling behind abutment, wing wall and return wall complete as per drawing and technical specifications. |
| 35 | Granular material |
| 36 | Sandy Material |
| 37 | Providing and fixing 15 cm dia & 1.00m long RCC Guard posts including all costs & conveyance etc complete. |
| 38 | Providing fitting & fixing stripseal expansion joints with M.S. Angles 75mm. X 75 mm. X 6 mm. at the edges of the slab with suitable anchoring arrangements by 12mm. M.S. Bars as per MoST design & drawing including fitting, fixing & welding with 6 mm. plates & filling joints of wearing coat with bitumen joint filler 12 mm. thick & joint sealing compound at top including painting of exposed surface of M.S. covered plates with anticorrosive bitumanstic paint etc. with cost, conveyance taxes of all materials labour & T&P etc. complete in all respects as per specification & direction of the Engineer-in-Charge as per clause 1403 of MoRD specification. |
| 39 | Providing fitting fixing expansion joint with Salitex board with cost conveyance as per the direction of Engineer - in charge . |
| 40 | P.C.C(1:3:6) using 40mm size H.G.metal well rammed with cost, Conveyance , royality,taxes of all material and labour,T & P etc.Complete. |
| 41 | Fixing of anchoring bars upto 25mm to 38mm dia in foundation rock in abutments and piers including drilling holes, fixing wedged anchors and grouting with cement mortar 1:4 complete as per the direction of Engineer in charge excluding cost of M.S. rods . |
| 42 | Levelling the hard rock surface under wells for piers, abutments & wing under water |
| 43 | Providing and applying two coats of water based enamel paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescense and applying paint @ 1 litre per 02 Sqm |
| 44 | Providing and erecting Informatory retro-reflectorised sign as per IRC-67-2012 made of class-B retro-reflective sheeting of high intensity prismatic grade sheeting as per ASTMD4956-09type-III and IV strictly conforming to clause 6.7of IRC67-2012 and vide clause 801.3, fixed over aluminium sheeting, 2.00mm thick as per clause 6.5.2 of IRC:67-2012 or A.C.P (Aluminium Composite Panel) used for sign boards with a thermo plastic core of blow density polythylene (LDPE) between two thick sheets of aliminium with over all thickness of 4mm and aliminium thichness of 0.5mm on both sides supported on mildsteel square post 80mmx80mmx3mm, 2nos and 5nos horizontal and 3no vertical extra supporting member of M.S pipe of size 50mmx50mmx3mm firmly fixed to the ground by means properly designed foundation withM-15 grade cement concrete 90cmx90cmx15cm, 150cm below ground level of as per approved drawing including cost, conveyance, royality, taxes of all materials, labour, T&P, excavation, curingetc. complete,under supervision of Engineer-In-Charge.Size-12'X8'(3657mm x 2438mm Rectangle) |
| 45 | Information Board of Size-12'X8' (3657mm x 2438mm Rectangle) Please Enable Macros to View BoQ information |
