|
| 1 | Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level.In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc.Depth upto 1.5 m |
| 2 | Random rubble masonry with hard stone in foundation and plinth :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 3 | 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) including pointing with cement mortar 1:2 (1 cement : 2 stone dust) with an admixture of pigment to match the shade of stone.Red sand stone |
| 4 | Kota stone slab flooring 25mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :Area of each slab 900 to 2000 sqcm |
| 5 | Earth filling with available surplus soil excavated from foundations and taken only from outside of building plinth in layers not exceeding 20cm in depth, consolidating each deposited layer including ramming and watering and consolidation with lead up to 50 m and lift upto 1.5 m. |
| 6 | Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart. |
| 7 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 8 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 10 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.Jhunjhunu / Jalore (Red / Chocolate Colour) 1501 Cm2 to 3600 Cm2 Tiles |
| 11 | Supplying and stacking good earth at site of work. Note: 1) Loading, unloading and carriage to be paid extra as per actuallead. 2) Earth measured in stacks will be reduced by 20% foe payment |
| 12 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 13 | Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and binding all complete. Hot rolled deformed bars |
| 14 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 15 | Grassing with 'Doobs' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed. (The good earth shall be paid separately) In rows 7.5 cm apart in either direction |
| 16 | Supply and planting following species best quality container grown healthy trees of 2 mt. min. height, well established & free from disease at site in 0.90 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required. Plumeria alba ( Champa) |
| 17 | Supply and planting following species best quality container grown healthy trees of 2 mt. min. height, well established & free from disease at site in 0.90 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required.Gulmohar(Delonix regia) |
| 18 | Supply and planting following species best quality container grown healthy trees of 2 mt. min. height, well established & free from disease at site in 0.90 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required.Bougain villea |
| 19 | Supply and planting following in poly bags / earthen pots well branched, well established & free from disease of 900 mm min. height plants at site in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, backfilling the hole watering etc as required.Ficus panda |
| 20 | SURF BOARD Provoding and fixing of Surf Board of size 910mm (Length) 860mm(Width)x:400mm(Height) fabricated with a center pipe of 100mm nominal bore shall be made form 'C' class G.I. Pipe the steeve pipe shall be made of 125mm OD seamless pipe with thickness of smm and bolted to main frame with M10 SS bolts, the bottom Support shall be welded of M.S. Plate of Q 250 mm & 10mm thickness, the handle frame of 25NB shall be made from 'C' class G.L. pipe the paddie frame of 50NB shall be made from 'C' class G.I. pipe supported with 70X8mm bend M.S. flat and can be replacable the foundation to be used for fixing should be a structure and shall be made from center pipe G.I. of 80NB 'C' class welded with M.S. round plate of 250mm & 10mm thick. main pipe shall be supported with 25mm x 25mm M.S. angle of 3mm thickness and 20mm x 40mm CRC square pipes of 3 mm thickness. boshes shall be used of 70 mm Outer Diameter with 5mm thickness. the footests shall be made from aluminum casting material of size 320ins to be used of diameter 35mm,25mm and 17mm shall be made up from SAE 8620 bright the bearings shall be used of \\"6007zz\\" \\"62 and \\"6203zz\\" permanent lubricated sealed bearings shall be used of \\"6007zz\\" () high tensile steel with galvanized nuts and bolts shall be used for assembly, the powder coating shall be done with pure polyester poeders of ackzonoble of berger paints with 60 to 70 Micron thickness. A16, A24 mm circlips shall be used for assembly. bolt M8X16 mm and NY lock nut of M8 shall be madeof SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust, all complete as per drawing design. directions and approval of engineer-in-charge regarding material, shape of equipment, colour (of metal, seat and pedal), and fixing |
| 21 | CROSS TRAINER Providing and fixing of cross trainer of size 1320 mm (Length) x 600mm (width) x1750mm (Height) fabricated with the main frame pipes of 80 NB shall be made of 'C' Class G.I and pipe with single bend pipe ith 250mm radius. The bottom support of M.S. round plate of 250 mm & 10mm thick. the Handle frame shall be made up of 25NB \\"C\\" Class G.I. Pipe the foundation Should be used for fixing is a structure and shall be made from center pipe of G.I. pipe of 80 NB \\"C\\" Class weled with M.S. round plate of 250 mm & 10mm thick. Main pipe should be supported with 25mm x 25mm M.S. angle of 3 mm thickness and 20mm x 40mm and CRC Square pipes of 3mm thic to build structure bushes to be used which shall be made from M.S Pipe of 60mm OD with 5 mm thickness, the footrests shall be made from Aluminium casting material of size 130mm X310mmx5mm thickness and mounted on M.S. plate of size 130mmx310mmx3mm thick. Pmm x270mmx5mm for support to footrest of 200mmX250mm with 3mm thickness M.S. plate shall be used closting caps shall be made up of high quality fiber reinforced plastic material, the bearing shall be used are of \\"6007zz\\" permanent lubricated sealed bearing of reputed brand (SKF/FAG), High tensile steel with galvanized nut bolts shall be used for assembly. the carclips shall be used for assembly of berger with 60 to 70 micron thickness. all complete as per drawing, design, directions and apporoval of Engineer- ncharge regarding material, shape of equipment, colour (of Metal, seat andpedal), and fixing of equipment etc all. shape of. |
| 22 | Provoding and fixing of thi-chi spinner (2 wheel) of size 700mm (length) x 1000mm (width) x 1280mm (height) fabricted with a center pipe of 200NB Shall be made up of \\"C\\" class G.I. pipe the handle movemetn round frame shall be made up from 25 NB \\"C\\" class G.I. pipe the foundation should be used for fixing is a structure and shall be made from center pipe of G.1. 80NB \\"C\\" class welded with M.S. round plate of 250mm & 10mm thick main pipe shall be supported with 25mm x25mm M.S. agnles of 3mm thickness and 20mm x 40mm CRC squre pipes of 3mm thickness. closing caps shall be made up of high quality fiber reinforced plastic material the pins to be used shall be made up of 25mm of SAE8620 bright material the bearing shall be used of \\"6201zz\\" & \\"6205zz\\" permanent lubricated sealed bearing of requted brand (SKF/FAG) high tensile S.S. nut bolts shall be used for assembly. fundation cover closing cap shall be made from FRP Material with 0.7 mm thicknes the cerclips used for assembly shall be of of A24 and All the nylon bush shall be used for handle knob. the powder coating shall be done with pure polyester powders from ackzonoble or berger paints with 60 to 70 micron thickness. bolt M8x16mm nd nylock nut of MB shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pips from rain and dust all complete as per drawing, design, directions and apporval of engineer in charge regarding material, shape of equipment, colour metal, seat and pedal) and fixing of equipment etc |
| 23 | SEATED PULLER Providing and fixing of seated puller of size 1900mm (length) x 740mm (Width) x 1920mm (Height) fabricated with a center pipe is of 100NB shall be made from \\"C\\" class Gl. pipe Bottom support of M.S round plate of 250mm & 10mm thickness shall be welded All linkages shall be made up of 25NB \\"C\\" class G.1. pipe the handle frame of 32NB \\"C\\" class G.I. pipe the seat frame of 32NB \\"C\\" class G.1. pipe to build structure bushes to be used which shll be made from seamless pipe of 60mm O.D. and Smm thickness as well as 60mm diameter solid bar bush shall be made from center pipe og G.I. of 80NB \\"C\\" class welded with M.S. round plate of 250mm & 10mm thick. Main pipe shall be supported with 25mm X 25mm M.S. angles of 3mm thickness and 20mm X 40mm CRC square pipes of 3mm thickness. foundation cover costing cap shall be made from FRP Material the seats and back rests to be fitted on the outer frames shall be made up of M.S. sheet of size 330 mm X 300mmX2mm thickness and deep and ressed in tools and diles to have uniform radius of 20mm with no sharp closing caps shall be made up of high quality fiber reinforced plastic material pips to be used of diameter 25mm and 17mm shall be made up from SAE 8620 bright material the bearings shall be used of \\"620zz\\" and \\"6203zz\\" ermanent lubricated sealed bearing of requted brand (SKF/FAG) high tensile steel with galvanzed nuts & bolts shall be used for assembly, the cerclips to be used for assembly are of A16 the power costing shall be done with pure polyester powders of ackzonoble or berger paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and apporoval of engineer in Charge regarding material, shape of equipment Colour of metal, seat and pedal) and fixing of equipment etc. |
| 24 | SEATING & STNDING TWISTER providign and fixing of seating & standing twister of size 1700mm (Length) x 540mm(width)x 1250mm (Height) fabricated with a center pipe of 100mm NB shall be made from \\"C\\" class G.I. round pipe the M.S. round plate of 250 mm & 10 mm thickness shall be welded at bottom. handle and bottom sleeve pipe of 125mm OD with thickness 5mm should be provided for easy assembly, replacement and maintenance, the bottom frame of the seating & standing twister of 32NB 50 NB and 25 NB shall be made from \\"C\\"class G.I. pipe the handle frame of seating & standign twister of 25 NB & foot resting frame of seating side shall be made from \\"C\\" class G.I. pipe of 25mm NB the foundation should be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB \\"C\\" class welded with M.S. round plate of 250 mm & 10mm thick main pipe shall be supported with 25mm X 25mm M.S. angles of 3 mm thickness. and 20mm x 40mm CRCA square pipes of 3mm thickness, the twister plate to be fitted on the bottom frame shall be made up of M.S. round plate of size 300mm dimeter and 10mm thickness, closing caps shall be made up high quality fiber reinforced Plastic mterial, the pins to be used which shall be up of 35 mm SAE 8620 bright material, the bearings shall be made of fo \\"6205zz\\" permanent lubricated sealed bearing of reputed brand (SKF/FAG) high rensile steel with galvanized nuts & bolts shall be used for assembly the powder coating shall be done by pure polyester powder of berger paint with 60 to 72 micron thickness, all complete as per drawing, design, directions and approval of engineer-in-charge regading material, shape of equioment colour (of metal seat and pedal), and fixing of equipment etc. |
| 25 | PUSH UP BARS Providing and fixing of push up bars of size 1220mm (length) x 550mm (width) x 1700mm (Height) fabricated with the main frame of 100 NB shall be made from \\"C\\"class G.L. pipe the M.S. round plate of 250mm & 10mm thickness shall be welded at botto the handle frame of 25 NB shall be made from \\"C\\" class G.1. pipe the foundation shoud be used for fixing is a structure and shall be made from center pipe of G.I. of 80 NB \\"c\\" class welded with M.S. round plate of 250mm & 10mm thick, main pipeshall be supported with 25 mm X 25 mm M.S. angles of 3 mm thickness and 20mm X 40mm CRC square pipes of 3mm thickness. closing caps shall be made up of high quality fiber reinforced plastic material foundation cover closing cap shall be made from FRP material, High tensile steel with galvanized unts & bolts shall be used for assembly, the powder coting shall be done with pure polyester powders of ackzonoble or berger paints with 60 to 70 micron thickness. all complete as per drawing, design, directions and apporval of engineer-in-charge regarding material, shape of equipmetn colour (of metal, seat and pedal) and fixing of equipment etc. |
| 26 | POMMEL HORSE Providing and fixing of pommet horse of size 2150mm (Length) x 800mm (Width) x 800mm (Height) Fabricated with the main frame of 80NB and 50Nb shall be made from \\"C\\" class G.I. pipe the handle frame of 32NB Shall be made from \\"C\\" class 1.pipe 40mm x40mm CRC square pipes frame shall be placed on the 25mm x 25mm x 3mm M.S. Angle with 60 X 10m thickness flat should be used for support, Closing caps shall be made up of high quality fiber reinforced plastic material high tensile steel with galvanized nutsa nd bolts shall be used for assembly. the powder coating shall be done with pure polyester powder Ackzonoble or berger paints with 60 to 70 micron thickness, all complete as per drawing, design, directions and approval of engineer-in-charge regarding material, shape of equipment colour (of metal, seat and pedal), and fixing of equipment etc. |
| 27 | SIT BOARD DOUBLE providing and fixing of sit up board double of size 1760mm (Length) x 1140mm (width) x 660mm (height) fabricated with the main frame of 25mm NB shall be made from \\"C\\" class G.I. pipe FRP sheet of 3mm thickness shall be moulded on main frame the remaining frame of the sit up board of 32mm NB shall be made from \\"C\\" class G.I pipe the powder coating shall be done with pure polyester powder ackzonoble or berger paints with 60 to 70 micron thickness the foundation shoud be used for fixing as structure and shall be made from center pipe G.I. of 80NB \\"C\\" class welded with M.S. round plate of 250mm & 10mm thick. M.S. main pipe shall be supported with 25mm x M.S. angles of 3 mm thickness. and 25mmx40mm CRC square pipes of 3mm thickness all complete as per drawing design directions and approval of engineer-in-charge regarding material shape of equipment colour (of metal, seat and pedal) and fixing of equipment etc. |
| 28 | DOUBLE TWISTER STANDY Providign and fixing of bouble Twister standing of size 1500mm (Length) x 600mm (width) x 1300mm (Height) Fabricated with a center pipe of 100NB shall be made from \\"C\\" Class G.I. material the bottomshall be welded with support of M.S. round plate of 250mm & 10mm thickness. The bottom frame of 32NB shall be made from \\"C\\" class G.I. pipe handle frame of 25NB shall be made from G.I. pipe the foundation should be used for fixing is a structure and shall be made from center pipe of G.1. of 80 NB \\"C\\" class welded with M.S. round plate of 250mm & 10mm thick. Main pipe shall be supported with 25 mm x 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC squarepipes of 3mm thickness, the Twister plate to be fitted on the bottom frame shall be made up of M.S. round plate of size 300mm and 10mm thick. Closing caps shall be made up of high quality fiber reinforced plastic material pins to be used of diameter 35mm shall be made up from SAE 8620 bright material the bearings shall be used are of \\"6205\\" permanent fubricated sealed bearing of reputed brand heigh tensile steel with galvanized nuts and bolts shall be used for assembly the powder coating shall be done with pure polyester powders from ackzsnoble paints with 60 to 70 micron thickness. all complete as per drawing desing directions and approwal of engineer-in-charge regarding material shape of colour (of metal seat and pedal) and fixing of equipment etc. |
| 29 | CHEST PRESS Providing and fixing of chest press of size 200mm (Length) x 210mm (Width) x 220mm (Height) fabricated with the center pipe of 100NB shall be made up \\"C\\" class G.I. pipe the bottom shall be welded with support of M.S. round Plate of 250mm & 10mm thickness. the connecting pipe shall be made up from 25NB \\"C\\" class G.I.pipe the handle frame shall be made up from 32NB \\"C\\" class G.1. pipe to build structure bushes to be used which shal be made from MS seamless pipe of 60mm O.D and 5mm thickness as well as 60mm diameter sold bar bush shall be used the foundation should be used for fixing is a structure and shall be made from center pipe of G.I. pipe of 80 NB \\"C\\" class welede with M.S. round plate of 250 mm & 10mm thick. Main pipe shall be supported with 25mm x 25mm M.S. agnlcs of 3 mm thickness and 20mm X 40mm CRC square pipes of 3mm thickness the seats and back rests to be fitted on the outer frames shall be made up of M.S. sheet of size 330mm X 300mmX 2mm thickness and deep drawn and pressed in tools and dies to have unifonn radius of 20mm with no sharp edges. closing caps shall be made up of high quailty fiber reinforced plastic material foundation cover cap shall be made from FRP material with 0,7 thickness, pins to be used diameter 25mm and 17mm shall be made up from SAE 8620 bright material. bolt MBx16mm and nylock nut of MB shall be made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust, the bearings shall be used are of \\"6205ZZ\\" & 6203zz\\"permanent lubricated sealed bearing of reputed brand (SKF/FAG) high tensile steel with galvanized nuts & bults shall be used for assembly, the cerclips to be used for locking shall be made up of A24mm & A16mm the powder coating shall be done with pure polyster powder from Ackzonoble or Berger paints with 60 to 70 micron thickness) all con leter as per drawing, design, directions and approval of Engineer-in-charge regarding material, shape of equipment colour (of metal. seat and pedal), and fixing of cquipment etc. |
| 30 | Designing, supply erection, commissioning and testing of heavy Foamming jet fountains having bunch of white foaming water 07 nos. Nozzle outside made out from Aluminium Alloy casted with inside ABS plastic moulded two piece assembly for smooth runnung white foaming jets water. Main Line made out from Surya/ Jindal/ Apolo or eq make in size of 2 inch B class Gl pipe line. Nozzle Mounted on ball joints assembly Alumimium Alloy casted inclusive of fountain nozzles each fully adjustable for a precision effect. Main Line Mainifould of Mild Steel dully Powder Coating. All Nut & bolts are G.1, PU Gaskets, pipe work, manifold nozzles made of precision machined brass including all final epoxy finishing work of pipe surface etc. Cable 3 Corex 2.5 sq mm copper 10 Mtr and for pump and 4 core x 1.0 sq mm copper 10 Mtr for Light of Polycab/Finolex/JMP or equilant. Material of construction of various components Manifold: MS of 10\\" dia. -Epoxy coated Pipe work: 2 inch Surya/ Jindal/Apolo or Eq make 14 ft long. Fittings Like Elbow, Tee, Sockets, Brass Ball Valve,Ball Joint, Hex connector, Nipples, Hex nipple etc Nozzle: Aluminum with Engineering Plastic(ABS). Mounting Stand: fabricated steel-galvanized/epoxy coating |
| 31 | Designing, supply erection, commissioning and testing of 5.0 HP X 01 Nos of Monoblock Openwell submersible pump of Kirlosker make AC 3 phase 220/240 Volt, 50 cycle, supply with foundation bolt, suction stainless steel mesh cover duly 10 Ft 3 core cable insulated of Polycab/RR/JMP/ finolex make. |
| 32 | Supply and fixing of 5.0 HP X 01 Pump panel box for above pumps of CRC 18 gauge steel sheet enclosure with front Double door type and Top hut type with back wall mounting type and provision for incoming & outgoing cable dully Powder Coated paint finish. Panel comprising 1 No main incoming 4 pole MCB, and 2 Pole MCB 01 Nos. Panel back up HRC fuse for pump circuit, Contactors unit with overload relay, Main Door Start stop push button switch with LED Red, Blue, Green, Indicator for phase Light. LED Light sequencer arrangement at main door with connection strips for Lights and Pump both. Contactors unit with overload relay, all accessories must be or Cat. I duly tested. Supplier has to privede Test certificate from National testing lab for IP55. |
| 33 | Designing, supply erection, commissioning and testing of water proof high power LED lighting system manufactured by ISO 2015 certified company make Premier/Syska/Fontasia/ S.L. Fountain make shall change the colours continually RGB and produce 16.7 million colours shall consist of 9watt(1wx9) 12 volt lights comprising high quality waterproof luminaries, wiring shall be reputed make double insulated PVC with copper conductor not less than 0.75 sq.mm connection shall be fully waterproof. Luminaries shall have die cast aluminium alloy bodies for strength and totally protected by fused epoxy polyester coating on all surfaces. The wall thickness of Luminaries not less than 5 mm. Light with Hi Power LED's and Hi Power Reflactive lens 45 degree mounted on MCPCB not less than 2.0 mm Aluminium. All external nuts bolt and studs of AISI 304 standard stainless steel. High Class PVC Cable Gland shall be IP 68. Supplier has to privede Test certificate from National testing lab for IP 68. |
| 34 | LED Light sequencer of Premier / Oasis / S.L.Fountain make to change the colour. Sequencer is fully equiped with in built SMPS for 220 volt to 12 Volt Operations 02 Nos for 12 Lights one sequencer and for 4 lights. Sequencer is operated with remote to adjust time of changing colour with function of fixed light each colour as required etc. Controller has on off switch with remote sensor in in front. Controller body made out from 20 gauge CRC sheet dully Powder Coated. |
| 35 | WAVE SLIDERec Age: 3-8 yearThe area: 2.2m* 6.0 mSafe play area: 3.7m*2.1 mHIGHT: 3.654M In the mini wave slide the center support is made up of 80NB pipe. The slide portion is made in Fiberglass reinforced plastic. The thickness of the mini slide is 5mm with proper reinforcement to support the module. The trainforcement to support the module. The tringular steps of the slide are of 16 SWG and ladder frame is made in 25 NB powder coated Gl pipe. The ladder is designed in such a way ther won't be entrapment of childs foot while playing. All the sharp edges and corners properly grinded to give |
| 36 | ARCH SWING DOUBLE SEATERRec Age: 4-14 yearThe area: 3m 1.5 mSafe play area: 4*3.5 m The arch shaped side frame of the swing is made up of 80NB GI pipe and top 2 pipe is made up of 50 NB GI pipe. The frame is powder coated to give an ersthetic look. The two swings are made up 10 mm thick antiskid chequered reinforced rubber top. The belt seat is suspended on 6 mm rubber coated GI chain. The ball bearings are mounted inside a specially designed nylon clam |
| 37 | FOUE BOARD SEE - SAWRec Age: 3-10 yearThe area: 3m 0.5 mSafe play area: 4*1.5 mThe Ms See saw comprises four FRP seats The lever is consisted of 20 nb and 80 nb powder coated gi pipes. The bearing used in this item is heavy duty nylon bush type. The stand for see saw made using 50 NB Gi Pipe |
| 38 | TARZEN SWINGRec Age: 4-14 yearThe area: 3m 1.5 mSafe play area: 4*3.5 mThe arch shaped side frame of the swing is made up of 80NB GI pipe and top pipe is made up of 50 NB GI pipe. The 4 frame is powder coated to give an ersthetic look. The two swings are made up 10 mm thick antiskid chequered reinforced rubber top. The belt seat is susended on 6 mm rubber coated GI chain The ball bearings are mounted inside a specially desingned nylon clamp |
| 39 | Brick work with FPS bricks of class designation 75 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 40 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 41 | Supply and erection of Galvanized Iron pole with galvanizing done in single dipping (Average coating thickness Minimum 65 Microns) continuously tapered poles having Octagonal / Circular cross-sections designed to withstand the maximum wind speed as per IS 875, The pole shaft shall be made from sheet steel (HT Steel Conforming to grade S355JO) and confirming to BSEN 10025 and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The welding of pole shaft shall be done by Submerged Arc Welding (SAW) process. pole shafts shall be provided with the rigid flange plate of suitable thickness (Fe 410 conforming to IS 226 / IS 2062) with provision for fixing 4 no. foundation bolts, This base plate shall be fillet welded to the pole shaft at two locations i.e. from inside and outside.The octagonal Poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the Base plate with bakelite sheet having 6A SP MCB and 16 sqmm stud type connector ( 4 nos) inside the pole at door opening for cable connection of following length and dimension as per table P-01 with base plate and foundation bolt on the Existing cement concrete foundation.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .Poles with Octagonal Cross Section 6 Mtr. |
| 42 | Supply and Fixing of Pole OEM fabricated hot dipped galvanised M.S. Overhang (48.3 X 3.25 mm) with cap (400 x 88.9 / 114.3 x 3.25 mm) over the existing poles. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . Single arm overhang |
| 43 | Supply and Fixing of Pole OEM fabricated hot dipped galvanised M.S. Overhang (48.3 X 3.25 mm) with cap (400 x 88.9 / 114.3 x 3.25 mm) over the existing poles. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . Double arm overhang |
| 44 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 6 A to 32 A rating |
| 45 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 2 x 1.5 sq.mm |
| 46 | Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass cover and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <750mA. The luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .LED Street Light fixture with Minimum lumen output 7500 lm |
| 47 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 16.0 Sq. mm 4 core |
| 48 | P / L of Double wall corrugated HDPE pipe confirming to IS : 16205 P-24, Stiffness Class 750 N, Externally corrugated and having smooth surface inside with HDPE Coupler, Elbow, Tee at required Depth below the ground for laying cable of following Nominal Outer dia. MFR Test report from NABL accrediated is to be submitted.(Excavation of Earth & Back filling with compaction is to be Paid Extra)All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .50 mm |
| 49 | Pipe Earthing as per IS:3043- 1987 with 3.0 Mtr. Long, 40 mm dia. ' B ' class G.I. Pipe IS: 1239 (Part-1) 2004, Equivalent to BS : 1387 with perforated holes of 12 mm dia ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in-charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 50 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSRSingle pole MCB (With B/C curve tripping Characteristics); 50/63 A rating |
| 51 | Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering overall poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge.For additional technical parameters of product / work refer Annexure 'A' attached with this BSRTriple pole Isolator; 63 A rating |
| 52 | SITC of IP-42 and general construction confirming to IS:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as per PWD specifications for electrical works, made out of CRCA sheet & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 53 | Providing & Fixing of AC operated heavy duty 230 /440 Volt power contactor as per PWD specification for electrical Works, ISI marked IS/IEC 60947-4-1 : 2000 having provision of mechanical interlocking, auxilary contacts, Din rail mounting type including making connections, testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .3 pole Power contactors with following AC 3 Rating 70 Amp |
| 54 | Providing & Fixing of mechanical / digital time switch having following day / week programme and minimum 100 hours reserve and AC1 rating of 16-20 amperes including making connection, programming conforming to IEC 60730-1 and 60730-2-7 etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .One day & week reserve (Analog type ) |
| 55 | Supply and fixing different type of steel pre-fabricated garden bench/jhula/ slides and other children play items made of steel duly paintedas per approved design and specifications by engineer in-chargemade of MS pipe, Flats, rectangular hollow section or other steelsections duly welded and or nut bolted where ever required, rubbingand buffing welded joints to make safe for use of children andpainted in approved pattern complete as required. Please Enable Macros to View BoQ information |
