|
| 1 | Demolition of cement concrete of any description in sunken floor or in any position complete all as specified and directed. |
| 2 | M&L for Treatment of sunken floor slab compriases of the following specifications and all as specified :-. |
| 3 | (i) M&L for cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely and provn of 40mm thick average PCC 1:2:4 type B0 using 12.5mm graded aggregate as in padding conc to achieve proper slope. (ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with integral water proofing compound @ 3% BY WT OF CEMENT CONSUMED. Fill it with water and check dampness and seepage. Where dampness/seepage is noticed, nozzles shall be fixed and grouting to be carried out (WPC shall be measured and paid separately)(iii) All junctions points of side wall where CI/GI pipes are passing through shall be sealed with epoxy putty.(iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean.(v) M&L for applying two coats of polymer modified cementious water proof coating as per manufacturers instruction to bottom and vertical sides up to finished floor level +100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky,, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed. (This item shall be measured and paid separately).(vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound @3% wt of cment consumed as per manufacturer's specification including rounding of corners and junctions sloping towards spout. (WPC shall be measured & paid separately ) |
| 4 | (vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound @3% wt of cment consumed as per manufacturer's specification including rounding of corners and junctions sloping towards spout. (WPC shall be measured & paid separately ) Note :- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of GE. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing is included in the rates quoted above.(vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint (Black paint shall be paid separetely) |
| 5 | M&L for applying two coats of polymer modified cementious water proof coating as per manufacterors instruction to bottowm and vertical sides of sunken portion up to finished floor level +100 mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion complete all as specified and directed. |
| 6 | Supply only Integral Water proofing compound complete all as specified and directed. |
| 7 | M/L for PCC in 1:5:10 type E2 (using 40 mm graded agg) as in sunken floor of toilet complete all as specified and as directed.. |
| 8 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing all the rubbish as directed by Engineer-in-charge complete all as specified and directed. |
| 9 | M & L for non skid ceramic coloured tiles (Ist quality) 7 to 8 mm thick (Square/ rectangular), area of each tile exc 0.11 Sqm but n.exc 0.18 sqm as in floors etc laid over and including 15mm thick screed bed in CM 1:4 and set and jointed in neat grey cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 10 | M & L for non skid ceramic coloured tiles (Ist quality) 7 to 8 mm thick (Square/ rectangular), area of each tile exc 0.11 Sqm but n.exc 0.18 sqm on vertical surfaces such as skirting, dado and rises to steps etc. including 10mm thick cement plaster in CM 1:3 set and set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles complete all as specified and directed. |
| 11 | M & L Vitrified ceramic tiles of premium quality, light shade, 9-10 mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 Sq.m (size 600 x 600 mm), laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified. |
| 12 | M&L for vitrified coloured tiles of 600x 600 x 9-10 mm thick as in skirting set and jointed in neat cement slurry and pointed in colour cement over 10 mm thick rendering in cement mortar 1:3 including taking down old wall dado/finishes of any description, complete all as specified and directed. |
| 13 | Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 14 | Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 15 | Dismantling/taking out existing hessain base felt or any other existing water proofing treatment from roof including cement plaster and exposing the top surface of RCC slab including removing the dismantled debris to a distance exc 200m & n.exc 250m. all as specified and directed |
| 16 | M & L for providing 15mm thick rendering over roof slab in Cement Mortar (1:4) mixed with water proofing compound @ 3% by weight of cement, finished even and smooth surface without using extra cement all as specified and directed |
| 17 | M/L for water proofing treatment by applying oil bound bitumen primer, having a density of 0.87 - 0.89 Kg/lit, @ 0.40 ltrs/Sqm, providing and laying APP modified water proofing membrane weighting not les than 3.50 Kg/Sqm of approved make including minimum 10 cm side lap and 15 cm end lap, laid and pasted with blue flame torching applications and finally finishing with two coats of solar reflective bituminous aluminium paint @ 0.1.Kg/Sqm complete all as specified and directed. |
| 18 | Dismantling of single layer Mangalore pattern or similar tiles in roofing all as specified and directed. |
| 19 | M&L roof tiles, Mangalore pattern class 'AA', interlocking at side joints, laid dry complete all as specified and directed. |
| 20 | All as per Item No. 17 herein above but except tiles |
| 21 | M&L for Ridge or hip tiles to suit Mangalore pattern or roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and directed. |
| 22 | M&L for cement concrete type B0, 1:2:4 (12.5 mm graded aggregate) in roof kerbs or mud stops, roof pedding, bedding for tiles etc complete all as specified and directed. |
| 23 | Taking down and refixing in same opening of wooden door / window / CB shutters of any description, n exc 1 Sqm each including builders hardware as required including renewal of unserviceable screws, etc.complete all as specified and directed. |
| 24 | Taking down and refixing in same opening of wooden door / window / CB shutters of any description, exc 1 Sqm but not exc 2 Sqm each including builders hardware as required including renewal of unserviceable screws, etc. complete all as specified and directed. |
| 25 | Taking down of chowkat / frames with shutter (without taking off shutter from frames) n.exc 1.5 Sqm each ( Distrubed surface of wall shall be made good by the contractor. The rate quoted shall be deemed included for the same). |
| 26 | Taking down of chowkat / frames with shutter (without taking off shutter from frames) exc 1.5 Sqm but n.exc 4 Sqm each ( Distrubed surface of wall shall be made good by the contractor. The rate quoted shall be deemed included for the same). |
| 27 | Dismantling of wooden scantling 40 sqcm over in section in any position as in framed work complete all as specified. |
| 28 | S&F for second class hardwood LAUREL/ BIJASAL/ BENTEAK/ VENTEAK/ SAL/MATTI as in scantling timber fixed or in chowkhat, style and rails of joinery, wrought, fixed in repairs all as specified and directed. |
| 29 | S&F 2nd class hardwood panelled shutter, 35 mm thick, (two numbers of panels) panels inserted of 12 mm ply board or/veneered particle board. The size of rails and stile as per IS : 1003 (Part I) complete all as specified and directed by Engineer in Charge |
| 30 | S&F 2nd class hardwood factory made glazed skelton shutter, 35 mm thick, open rebated, without sash bars all as specified in clause 8.24(a) of SSR 01, section8, for doors. complete all as specified and directed by Engineer in Charge |
| 31 | M&L 2nd class Glazed and skeleton shutters 30mm thick, for windows/ventilators, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a), complete all as specified and directed. |
| 32 | M&L for applying 2 coats of synthetic enamel paint over a coat of primer or Pink Primer on new Wooden surface of girth over 10 cm, including preparation of surface complete all as specified and directed. |
| 33 | Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed. |
| 34 | S&F Mild steel framed work of as in grills/guard bars shouldered with wooden/steel window/ ventilator frames incl all necessary fixing accessories complete all as specified. |
| 35 | M&L for applying 2 coats of synthetic enamel paint over a coat of primer or red oxide on new steel surface of girth over 10 cm, including preparation of surface complete all as specified and directed. |
| 36 | S&F in repair 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in wall / cub board shutters/selves and the like, etc complete all as specified |
| 37 | M&L for 6mm thick external teak wood lipping fixed to18/19mm thick block board or veneered particle board fixed with nails complete all as specified and directed. |
| 38 | S&F extruded aluminium alloy butt hinges 100mm size with galvanised mild steel hinge pin type C-21 complete all as specified and directed |
| 39 | S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed |
| 40 | S&F Aluminium alloy sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed (Length of bolt in 300mm). complete all as specified and directed |
| 41 | S&F Aluminium anodised Cast type handle of 150mm size. complete all as specified and directed |
| 42 | S&F Aluminium anodised Cast type handle of 100mm size complete all as specified and directed |
| 43 | Resecuring or easing and adjusting without taking down shutter from the frame and re-fixing builders hardware as required including removal of unserviceable screws etc, n.exc 1 Sqm each, complete all as specified and directed by Engineer-in-Charge. |
| 44 | Resecuring or easing and adjusting without taking down shutter from the frame and re-fixing builders hardware as required including removal of unserviceable screws etc, area exc 1 Sq.m but not exc 2 Sq.m each, complete all as specified and directed by Engineer - in -Charge. |
| 45 | S&F in repairs Aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specifed and directed. |
| 46 | S&F in repairs Aluminium anodised barrel tower bolts of extruded section 200 mm long complete all as specifed and directed. |
| 47 | S&F in repairs extruded aluminium handles, fabricated type 100mm size all as specified and directed. |
| 48 | S&F in repairs extruded aluminium handles, fabricated type 150 mm size all as specified and directed. |
| 49 | S&F in repairs extruded aluminium alloy butt hinges 100mm size with galvanised mild steel hinge pin type C-21 complete all as specified and directed. |
| 50 | S&F in repairs Aluminum alloy, powder coated, sliding door bolt 250 mm long and not less than 12mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and directed. |
| 51 | Repairs to sliding door bolts of any size & type by tightening of screws including renewal of unserviceable screws or bolts, nuts and washers complete all as specified and directed. |
| 52 | Taking out old serviceable glass of any description, from old wooden or metal frames, or stone, concrete or brick surrounds, any thickness or size; hacking out old putty or removing beads etc, including making good breakages in taking out and handling removing to store or stacking for reuse complete all as specified and directed. |
| 53 | M&L for 3mm thick sheet glass, ordinary quality and glazing with wooden beading not exceeding 0.5 Sqm in each pane all as specified and directed. |
| 54 | M&L for 3mm thick figured glass, pin head type and glazing not exceeding 0.5 Sqm in each pane with and including wooden beading all as specified and directed. |
| 55 | S&F in repairs Aluminum Alloy wire cloth, 0.45mm nominal dia of wire & average width of aperture 1.40mm and fixed with wire staples all as specified and directed |
| 56 | S&F in repairs anodised Aluminium alloy curtain rod/hanging rod 19/20mm dia all as specified and directed |
| 57 | S&F in repairs anoised Aluminium alloy bracket with new screws for curtain rod all as specified and directed. |
| 58 | Taking up or down GI tubing 20 mm bore and connections all as directed. |
| 59 | Taking up or down GI tubing 25 mm bore and connections all as directed. |
| 60 | Supplying and fixing 20 mm dia UPVC pipes of pressure rating 10 Kgf/cm2 fixed complete to walls, ceiling or in floors etc including neccesary Fitting (bends/couple/ Reduser etc.) complete all as specified and directed. |
| 61 | Supplying and fixing 25 mm dia UPVC pipes of pressure rating 10 Kgf/cm2 fixed complete to walls, ceiling or in floors etc including neccesary Fitting (bends/couple/ Reduser etc.) complete all as specified and directed. |
| 62 | S&F in repairs stop valves/angle valve, cast copper alloy fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe of 15mm bore all as specified and directed. |
| 63 | S&F in repairs stop valves, cast copper alloy fancy type chromium plated with long shank and cup (concealed type) for iron pipe of 15mm bore of complete all as specified and directed. |
| 64 | S&F in repairs bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe 15mm bore complete all as specified and directed. |
| 65 | S&F in repairs Pillar taps cast copper alloy, fancy type, chromium plated with capstan heads screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe of 15 mm bore of complete all as specified and directed. |
| 66 | S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm long all as specified and directed. |
| 67 | S & F in repairs plastic water closet seat and cover, black, closed pattern with flat bottom suitable for pedestral / Semi pedestral pattern water closets and mild steel chromium plated or aluminised hinging device all as specified and directed. |
| 68 | Repairs to seat and cover for pedestal pan including adjusting the cover to its original position, tightening of hinging device using new bolts etc complete all as specified and directed. |
| 69 | S&F in repairs 32mm size waste fitting (coupling) brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed all as specified and directed. |
| 70 | S&F in repairs 40 mm size waste fitting (coupling) brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed all as specified and directed. |
| 71 | S&F in repairs 32 mm bore PVC waste pipe with fittings of approved make suitable for WHB, Urinals etc all as specified and directed. |
| 72 | S&F in repairs 40mm bore PVC waste pipe with fittings of approved make suitable for WHB, Urinals etc all as specified and directed. |
| 73 | S & F in repair mild steel Chromium Plated grating 125mm dia with or without waste hole fixed on floor/ nahani trap with cement mortar, fixed in repairs, complete all as specified and directed by Engineer - in -Charge. |
| 74 | S&F in repairs 32 mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fxied complete all as specified and directed. |
| 75 | S&F in repairs brass chromium plated mixer for mixing hot & cold water screwed down for 15mm dia iron pipe of complete all as specified and directed. |
| 76 | S&F in repairs 600 mm x 450 mm bevelled edge mirror of 5.00mm thickness of selected quality glass,mounted on 6mm thick Asbestos Cement building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified and directed. |
| 77 | S&F in repairs Vitreous china ware water closet Orissa pattern including 'P' or 'S' trap connecting to trap and to flushing pipe anti Syphonage pipe etc complete with foot rest of size 580mm X 440mm (jointed with epoxy raison to glazed trap) including provision of lime concrete bedding complete all as specified. |
| 78 | S&F in Vitreous China wash basin, white, flat back, size 630x450mm excluding ditto but including brackets all as specified and directed. |
| 79 | S&F in repair WHB vitreous white chinaware of 550x400 mm size including CI/MS brackets, 450mm long PVC connection. PVC waste pipe of suitable size/length, 15 mm dia CP pillar tap, 32mm dia brass chromium plated waste fitting, 32mm dia waste coupling of PTMT (half or full threaded) and all connection complete all as specified and directed. Please Enable Macros to View BoQ information |
| 80 | S&F in repair WHB vitreous white chinaware of 550x400 mm size including CI/MS brackets, 450mm long PVC connection. PVC waste pipe of suitable size/length, 15 mm dia CP pillar tap, 32mm dia brass chromium plated waste fitting, 32mm dia waste coupling of PTMT (half or full threaded) and all connection complete all as specified and directed. Please Enable Macros to View BoQ information |
