|
| 1 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out any type of soil complete all as specified and as directed |
| 3 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed |
| 4 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed |
| 5 | M&L for pre cast cement concrete Type D2 1:4:8 (using 40mm graded stone aggregate) as in foundations,filling and mass concrete complete all as specified and as directed |
| 6 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 7 | All as per item no 6 above, but , 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed |
| 8 | M&L for form work to sides (in curved shape) of concrete foundations, footings,rafts and raft beams sides and soffits of foundation and plinth beams and similar work, rough finished surface all as specified and directed. |
| 9 | M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed |
| 10 | M&L for Design mix RCC M-25 (using 20mm graded stone aggregate) as in design mix Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed |
| 11 | M&L for Reinforced cement concrete (design mix RCC M-25 using 20mm graded stone aggregate)in Columns,pillars, piers,posts and strut complete all as specified and as directed |
| 12 | M&L for Design mix RCC M-25 (using 20mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 13 | M&L precast cement concrete block masonry not exc 10 cm width with solid block PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) and setting in cement mortar 1:4 complete all as specified and as directed |
| 14 | M&L precast cement concrete block masonry exc. 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) complete all as specified and as directed |
| 15 | M&L for rolled section as in main and cross beam, hip and jack rafter,purline where connected to common rafters and running rails and guides for sliding doors fixed witg angle cleats or other connecting plates of grade Fe-410 (grde E-165) complete all as specified and as directed |
| 16 | M&L for aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering and including dismantling of old wind tie complete all as specified and as directed |
| 17 | M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying 2 coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed |
| 18 | S&F for pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an coloure having tensile strength of 550Mpa as in roof covering fixed with self tapping screws complete all as specified and as directed |
| 19 | S&F for pre painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering, ridge, eves gutters etc fixed with self tapping screws complete all as specified and as directed |
| 20 | M&L for rendering 15mm thick in CM 1:4 including mixing water proofing compound on concrete/block masonry surfaces and finished even and smooth without using extra cement complete all as specified and as directed |
| 21 | M&L for 10mm thick plaster in CM (1:6) on fair faces of concrete/PCC block surfaces of walls finished even and smooth (without using extra cement) complete all as specified and as directed |
| 22 | M&L for preparation of newly plastered wall surfaces and applying two coat of oil bound distemper over one coat of primer including leveling the surface with one coat of putty complete all as specified and directed. |
| 23 | M&L for preparation on newly plastered external wall surface and applying two coat of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint complete all as specified and as directed. (Make: Dulux Weather Shield Max or Apex Ultima from Asian Paints or Berger weather coat All guard). |
| 24 | S&F Powder coated aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. |
| 25 | Supply and fix aluminium alloy wire mesh 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples complete all as specified and as directed |
| 26 | S&F for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge |
| 27 | S&F for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of sliding doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene asket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, auminium snap beading for glazing/ paneling, C.P. brass/ tainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 28 | S&F floor door stopper of aluminium alloy body & tongue, anodised with hard drawn spring of 140mm size fixed in floor complete all as specified and directed |
| 29 | S&F in butt hinges extruded aluminium alloy with galvanized mild steel hinge pin ,anodized of hinges 100 mm type B-21 complete all as specified and as directed |
| 30 | S&F extruded aluminum alloy handle fabricated type anodized 150mm long complete all as specified and as directed |
| 31 | S&F Aluminum anodized barrel bolt of extruded section 150mm long complete all as specified and as directed |
| 32 | S&F Aluminum alloy anodized sliding door bolt 300mm long with hasp and staple (bolt type) and fixing bolts and sliding bolts of extruded such or cast aluminum alloy complete all as specified and as directed |
| 33 | S&F Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube, fixed in opening as per specification complete all as specified and as directed |
| 34 | S & F for Factory made solid PVC moulded with particle board core door shutter 28 to 30 mm thick panel design with 2mm thick molded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing complete all as specified and as directed |
| 35 | M&L 16 to 20mm thick granite stone (of any type ) work (table rubbed and polished) in floors, staircase tread & risers of steps, cooking platform, window cill/jambs etc laid bedded over 15mm thick CM (1:4) bedding & pointed in white/coloured cement to match coloured tiles including Rounding, grinding and mirror polishing complete. (Note : Colour of granite shall be as approved by Engr-In-Charge) |
| 36 | M&L for non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thick screed bed in CM 1:4 complete all as specified and as directed. |
| 37 | All as per item No 36 above, but , as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3,complete all as specified and as directed |
| 38 | Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes complete all as specified and as directed |
| 39 | Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified. |
| 40 | S&F for anodoised aluminium powder coated snap grid frame work for ceiling 605mm x 605mm using aluminium anodoised sections specified in SSR part-I 1991 including cutting, drilling jointing ect complrtr including 4mm dia of GI hangers wire suspenders fixed with adjustable connectors and providing 6mm thick E-boards (Classic) 605mm x 605mm size Specified by Engr-in-charge and making good complete all as specified and as directed |
| 41 | S&F for 75 mm PVC (SWR) vent cowl complete all as specified and as directed |
| 42 | S&F for 75 mm dia PVC (SWR) grade bends of any radius complete all as specified and as directed |
| 43 | S&F PVC (SWR) pipe 75mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed |
| 44 | S&F for 110mm dia PVC (SWR) bends any radius complete all as specified. |
| 45 | S&F for 110mm dia PVC (SWR) vent cowl complete all as specified. |
| 46 | M&L for 75 mm PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and as directed |
| 47 | S&F for 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified and as directed |
| 48 | S&F vitreous china ware wash hand basin white flat back of size 550x 400 mm with pedestal including brackets, 32 mm CP waste coupling, chain and plug, waste fittings, and all necessary inlet, out let connections complete all as specified and as directed |
| 49 | S&F 15 mm bore pillar taps, cast copper alloy, chromium plated fancy type screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts complete all as specified and as directed.Make : Prayag Cat No. PIS-50H or equivalent in Jaquar/Soma/Leader |
| 50 | S&F for bib taps long body with flange cast copper alloy chromium plated fancy type with crutch or butter fly handle screwed down for Iron pipe or for brass fancy for CP brass fancy type 15mm dia complete all as specified and as directed. Make : Prayag Cat No. PIS-08H or equivalent in Jaquar/Soma/Leader |
| 51 | S&F Hand shower (health faucet) with 8mm dia & 1.0mtr long flexible tube with wall hook complete all as specified and as directed Make PrayagCat Part No. BEA-41 or equivalent in Jaquar /Hindware |
| 52 | S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed |
| 53 | S&F CP overhead shower dia 125 mm overhead shower round with revolving joints (with body rotation) & 225mm long arm shower with rabit cleaning system and all fittings complete all as specified and as directed. Make - Prayag BS-76 or equivalent in Jaquar /Kohler/ESS-ESS |
| 54 | S&F rotational moulded Polyethylene [HDPE] Water Tanks, Triple Layered, ISI Marked Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes including taking down old tanks complete all as specified and as directed by Engineer- in - charge. |
| 55 | S&F in repairs Ball valves high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe bore dia of 25mm (Minimum weight 455 gms) complete all as specified and as directed by Engineer- in - charge.MAKE: PRAYAG/POLYTUFF/PRINCE |
| 56 | S&F in Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete all as specified and as directed |
| 57 | S&F in repairs two way bib cock cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shank and cup complete all as specified and as directedMake : Prayag Cart Part No PIS-12 H or equivalent in Jaquar/Soma/Leader |
| 58 | S&F in repair PVC valveless syphonic action type flushing cistern 10 ltr capacity white with intel ball valve float flush pipe and handled including brackets complete all as specified. |
| 59 | S&F in repairs Brass chromium plated tubular towel rail 20mm dia & 60 cm long between flange complete all as specified and as directed. Make : Prayag Cat Part No. BA-70 or equivalent in Crown/Jindal/ESSESS |
| 60 | S&F in repairs PVC connection 15 mm dia and 600 mm long with both and nuts complete all as specified and as directed |
| 61 | Excavating over areas, n exc 1.5 m deep and getting out in Soft/Loose soil complete all as specified and directed |
| 62 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and getting out in soft / loose soil complete all as specified and directed |
| 63 | M&L for formwork to staircases with sloping or stepped soffits including risers and stringers (excluding landing) complete all as specified and directed |
| 64 | M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed |
| 65 | M&L for reinforced cement concrete (Nominal Mix) type A1, 1:1.5:3 ( 20 mm graded aggregate ) as in landings of staircase complete all as specified and as directed |
| 66 | M&L for reinforced cement concrete (Nominal Mix) type A1, 1:1.5:3 ( 20 mm graded aggregate ) as in staircase, including steps (square or spandril), string pieces complete all as specified and as directed |
| 67 | M&L for reinforced cement concrete (Nominal Mix) type A1, 1:1.5:3 ( 20 mm graded aggregate ) as in Columns, pillers complete all as specified and as directed |
| 68 | S & F stainless steel tubing of any diameter of circular, square or rectangular in shape of grade AISI-316 (type Austenitic anticorrosive in nature) as in railings / grills / designer work including post top cap, bottom plate, cutting, bending, seamless welding and fixing in any type of location incl taking down old railing of any description complete all as specified and as directed. |
| 69 | M&L for 75 mm thick Cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing.complete all as specified and directed. |
| 70 | S&F for glossy finished chequerred cement concrete tiles 30cmx30cmx25mm thick set jointed with grey cement and pigment and pointed in neat cement slurry including 20 mm thick screed bed of CM(1:6) in floors Please Enable Macros to View BoQ information |
| 71 | S&F for glossy finished chequerred cement concrete tiles 30cmx30cmx25mm thick set jointed with grey cement and pigment and pointed in neat cement slurry including 20 mm thick screed bed of CM(1:6) in floors Please Enable Macros to View BoQ information |
