|
| 1 | M&L Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil, complete all as specified and directed. |
| 2 | Excavating in trenches in soft/ disintegrated rock n exc 1.5m wide and n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out, complete all as specified and as directed by the Engineer-in-Charge. |
| 3 | Removal of surplus soil to a distance of outside MoD and depositing where directed at a level not exceeding 1.5 Metre above the starting point, complete all as specified and directed. |
| 4 | Returning, filling in soft/ disintegrated rock including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils, complete all as specified and directed. |
| 5 | M & L for Hardcore Broken stone/boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed by the Engineer-in-Charge. |
| 6 | M&L for Anti-termite treatment to bottom and sides of excavation by applying chemical emulsion at the rate of 5.0 litres per square metre of surface area using approved anti-termite chemical such as Chlorpyrifos 20% EC or equivalent, diluted in water to achieve 1% concentration as per IS:6313 (Part-II), applied uniformly over the entire surface including bottom and vertical sides of excavation by spraying or rodding method to ensure proper penetration into soil, including preparation of solution, application with suitable equipment and all labour, materials and tools required to complete the treatment effectively, complete all as specified and directed by Engineer-in-Charge. |
| 7 | M&L for 40mm thick Damp proof course mix with liquid water proofing compound @ 200ml of 50kg of cement, to horizontal or vertical surface including necessary formwok in cement concrete 1:2:4, type B-0 using 12.5mm graded stone aggregate and applying evenly a coat of blown type bitumen at the rate of 1.50kg per square meter and blinding with clean dry sand @0.05cu.m. per sqm all as specified and directed. (Note:-LWP shall be measured and paid seperately). |
| 8 | Use of Formwork to sides (in rough finished concrete but flat surface) of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed. |
| 9 | M&L reinforced cement concrete type B-1 1:2:4 (20mm graded crushed stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed. |
| 10 | M&L for Mild steel bars TMT 10mm and over dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to, complete all as specified and directed. |
| 11 | M & L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. |
| 12 | M & L for Cement concrete in foundation filling and mass-concrete Type B-2 (1:2:4), using 40mm graded stone aggregate, complete all as specified and directed. |
| 13 | M&L for Precast cement concrete 1:3:6 type C-1 (Using 20 mm graded aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed. |
| 14 | M & L for Machine cut cudappah stone slab 20-25mm thick including 20 mm cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed. |
| 15 | M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finishing the surfaces even and smooth with out using extra cement, complete all as specified and directed. |
| 16 | M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces, finishing the surfaces even and smooth with out using extra cement, complete all as specified and directed. |
| 17 | Preparation of new plastered surfaces of wall and for applying Two or more coats of 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance asper IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces, complete all as specified and as directed by the Engineer-in-Charge. |
| 18 | Providing and applying the Priming new plastered surfaces with one coat of alkali resistant priming paint of approved brand and manufacture, followed by distempering with two or more coats of oil bound washable distemper of approved brand and manufacture and of required shade, including preparing the surface by scrapping, sand papering, and applying putty/surface filler to give an even shade, all complete as per manufacturer's specifications, complete all as specified and directed. |
| 19 | M & L for 75mm Cement concrete type D-2, 1:4:8 (40mm graded aggregate), complete all as specified and as directed by the Engineer-in-Charge. |
| 20 | M&L for 25mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregates as in flooring, complete all as specified and directed. |
| 21 | M&L for Non Skid ceramic tiles colour tiles 8- 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes, complete all as specified and directed. Note : Work will be in patches or in bulk. |
| 22 | M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 600X1200mm of thickness 7 to 10 mm in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick screed bed in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles, complete all as specified and directed. |
| 23 | M&L for providing and fixing porcelain/vitrified tiles of size 600x1200 mm (ceramic & vitrified), tiles 8 to 10mm thickness, full body or glazed type, with antibacterial, non-slip and wear-resistant properties, of approved make and shade, in gloss/matt/rustic/satin finish, laid on cement mortar 1:4 bedding or with polymer-based tile adhesive as specified, including cutting, edge finishing, jointing with white/coloured cement slurry or tile grout, and cleaning, complete, all as specified and directed by the Engineer-in-Charge. |
| 24 | Supply and fixing in new work non-skid, heavy duty vitrified floor tiles (full body or salt and pepper type), of approved make such as Nitco/Kajaria/Johnson, of size 600x600 mm and thickness 10 to 14 mm, laid over and including 20 mm thick cement mortar screed bed in CM 1:4, laid to proper line, level and slope, including grouting joints with grey/white cement mixed with suitable pigment to match the shade of tiles, complete all as specified and directed by Engineer-in-Charge. |
| 25 | Supply and fixing granite (of any type) tiles 20 mm thick, machine cut, laid over and including 20 mm thick cement mortar screed bed in CM 1:4, to proper line, level and slope, bedded and jointed with grey cement slurry and pointed with white cement mixed with suitable pigment to match the shade of granite stone, including grinding and polishing to a smooth and even surface, complete all as specified and directed by Engineer-in-Charge. |
| 26 | Supply and fixing new work 3 mm thick figured sheet glass of ordinary quality in aluminium sliding window shutters, fixed with aluminium glazing beads, EPDM/neoprene rubber gaskets, including necessary screws, packing, sealing and all accessories, complete to make the glazing water tight and properly secured in position, complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 27 | Supply and fixing new work 3 mm thick figured sheet glass of ordinary quality in aluminium sliding window shutters, fixed with aluminium glazing beads, EPDM/neoprene rubber gaskets, including necessary screws, packing, sealing and all accessories, complete to make the glazing water tight and properly secured in position, complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
