|
| 1 | Repairing of Engine (Model 697 NA) by dismantling, providing and fitting of following parts:- |
| 2 | Air compressor piston assembly conf to part no 352 130 02 17 |
| 3 | Oil Pump conf to part no 2525 1810 0121 |
| 4 | Engine Gasket conf to part no. 2525 9900 0103 |
| 5 | Camshaft bushes conf to part no. 352 050 00 50 |
| 6 | Valve Guide inlet conf to part no. 2534 0515 3402 |
| 7 | Valve Guide exhaust conf to part no.2503 4515 3407 |
| 8 | Valve Seat Ring inlet conf to part no 3520 531 631 |
| 9 | Valve Seat Ring exhaust conf to part no 2525 0115 3410 |
| 10 | CR Bearing Seat conf to part no 2525 0312 01 13 |
| 11 | Liner conf to part no 2525 01103702 |
| 12 | Inlet valve conf to part no 3520 530 101 |
| 13 | Inlet valve conf to part no 3520 531 505 |
| 14 | Cylinder Sleeve conf to part no 2525 1310 3707 |
| 15 | Dismantling the old / damaged Radiator assembly, providing and fitting of new radiator assembly with the help of Hydra Crane and special tool & tackles etc. complete as required at site |
| 16 | Opening of Crawler Track Assembly, Crawler Drive Shaft Assembly & Idler Shaft Assembly etc. from the Machine with the help of Gas Cutter set, Heavy Duty Hydra Cranes, Wooden Sleepers, Special T&P and dismantling the same by cutting rusted/jammed 200 Nos. shoulder bolts, Bushes & Pins etc. for removing the defected parts as required at site.( Crawler Track Assembly for both LH & RH) |
| 17 | Bushing conf. to Part No. 3205Z1 |
| 18 | Pin conf. to Part No. 3219Z3 |
| 19 | Side bar (RH) conf. to Part No. 3224Z2D1 |
| 20 | Side bar (LH) conf. to Part No. 3224Z2D2 |
| 21 | Seal conf. to Part No. 3218Z12 |
| 22 | Flat forged shoe 24” conf. to Part No. 3224N8 |
| 23 | Master Bushing conf to part no.3205Z2 |
| 24 | Shoulder Bolt conf. to Part No.3220T55 |
| 25 | Hex Nut conf. to Part No. 3220Z18D6 |
| 26 | Fitting of Crawler Drive Shaft Assembly, Crawler Idler Shaft Assembly & Crawler Track Assembly on the machine etc. with the help of Heavy Duty Hydra Cranes & special T&P after assembly the same by providing and replacement/ repairing of following parts as required at site |
| 27 | Crawler Drive Shaft Assembly for both LH & RHBushing conf. to Part No. 5T2589 |
| 28 | Hex Cap Assembly (5) 8”-18UNFx1-1/2”) conf. to Part No. 0626V113 |
| 29 | Lock Washer 5/8” conf. to Part No.3615V012 |
| 30 | Bushing conf. to Part No. 205T50 |
| 31 | Repairing of Sprocket-Driven (204N44) by re-metalling/ turning and milling for re-building of splines in original shape & size. |
| 32 | Crawler Idler Shaft AssemblyBushing conf. to Part No. 5T2589 |
| 33 | Grease fitting conf. to Part No. 44Z1D14 |
| 34 | Hex Cap Screw 5/8” -18UNFx1-1/2”) conf. to Part No. 0627V109 |
| 35 | Lock Washer 5/8” conf. to Part No.3615V012 |
| 36 | Complete cabin repair with providing and fitting MS sheets etc. complete as requiredat site. |
| 37 | Denting, painting complete as required as required at site. Please Enable Macros to View BoQ information |
