|
| 1 | Repair to pot holes any depth, not exceeding 1 Sqm each including sweeping free from dust and mud, or water scoring sunken surfaces in roads, paths etc cutting around edges to at least 25mm in depth, making good by applying a tack coat @ 5 Kg/ 10 Sqm , putting in premixed bituminous macadam , well rammed and sealed with binder 9.8 Kg / 10 m2 ,blinded with 0.09 m3 of stone chippings 6.3 mm size and again well rammed (including supply of premixed macadam ,binder and chippings) depth of holes exceeding 30mm complete all as specified and as directed |
| 2 | M&L for preparing black top surfaces by brushing with wire brushes for removing caked mud etc. Sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and as directed |
| 3 | Applying evenly a tack coat of Cationic Bitumen Emulsion (RS-1) conforming to IS: 8887 at a rate of application of 0.2-0.3 kg/sqm on bituminous surface as specified in Table 500-5 of MoRTH specification for road and bridge works 2013, using mechanical sprayer after cleaning of existing surface as specified and directed. |
| 4 | M&L for premixed bituminous macadam laid / rolled with power road roller 8 to 12 Tonne capacity and compacted to required gradient and camber ( consolidated thickness 75 mm or less ) all as specified and directed . |
| 5 | M&L for Bituminous premix semi dense asphaltic concrete (SDAC) 30mm (consolidated thickness) in single layer using paving bitumen of grade VG-30 with 5.5% minimum binder content mixed by weight of total mix as wearing course, using hot mix plant and laid by using mechanical sensor paver, rolled and compacted to required camber and gradient complete all as specified.(Note: No Extra payment shall be paid to the contractor for more quantity of bitumen than mentioned in Sch 'A'.) |
| 6 | M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed. |
| 7 | Supply and fixing in repair of cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of fixed on bituminous/concrete surface with suitable adhesive complete all as per manufacturers instructions Make : Mr Illumination/3M/Aktion/Dark eye. |
| 8 | Supply and fix in repair of solar cat eye aluminum alloy (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd complete as per manufacturers instructions etc. all as specified and directed. MAKE: 3M / TATA BP SOLAR / SA TRAFFIC SAFETY, Kolkata / BONS LIGHT PVT LTD, Ahmedabad / ASIAN CONTROLS, Mumbai. |
| 9 | Supply and fixing in repair metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed. |
| 10 | Demolition of cement concrete(unreinforced) in ground floors and paving nexc 15 cm thickness (below and above ground level) complete all as specified & directed. |
| 11 | M&L PCC (1:4:8) type D2 using 40mm graded stone aggregate 75mm thick as in sub base complete all as specified & directed. |
| 12 | M&L for laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 13 | M&L for laying laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not be more than 5 mm), including making drainage opening wherever required complete all as specfied and directed. Please Enable Macros to View BoQ information |
