|
| 1 | Earthwork excavation and depositing on bank within initial lead of 10m and initial lift of 2m as sand silt or other loose soil wet sand light black cotton soil and ordinary soil including excavated earth etc.complete , as per standard specification |
| 2 | Plain Cement Concrete 1:4:8 (one part of cement, four part of Crushed Stone Sand (M- Sand) and eight part of coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification |
| 3 | Random Rubble masonry in cm 1:5 (one cement and five sand) for foundation and basement using new rough stone and bond stone and including simultaneous pointing cost and conveyance of all materials etc complete with std., specification. |
| 4 | Brick work in CM 1:5 (one cement & five M Sand) using II class ground moulded bricks of size 9\\"X43/8\\"X 2 3/4\\" including finishing, curing, etc., complete complying with standard specification - 100CFT |
| 5 | Plastering with cement mortar 1:5 (one cement five sand) mix to 12mm thick including cost and coveyance of all materials to site finishing curing etc., complete. |
| 6 | Supplying and fixing of Cuddaph slab 38 mm thick including cost and conveyance of all materials etc., complete and labour charges for moulding curing and fixing in position etc. complete as directed by the departmental officer. |
| 7 | Manufacturing supplying and fixing of MILD STEEL DOOR made out of 50 x 50 x 6 mm M.S angle for outer frame,35 X 35 X 5mm M.S.Angle for outer frame of shutter. The entire shutter area shall be covered with CRC sheets (18 G) with 5Nos, of stiffners using M.S.Flats of size 25 X 6mm at equal intervals horizontally. The corners of the frames and shutter with CRC sheets shall be welded by adopting flash butt welding or any other suitable method. Provision towards 3Nos, of Hinges incase of single shutters / 6Nos,of Hinges incase of Double shutters of 125 X 31 X 1.25mm size placed at appropriate intervals and provisions shall be made for Tower bolts 2Nos, Aldrop 1No. The frame shall be provided with 6Nos,of Hold fast of 200mm length using 50 X 6mm M.S.Flat. The entire frame and shutter shall be provided with one coat of red oxide primer including cost of hold fasts,hinges, locking arrangements, handles wind appliences etc., complete and as directed by the departemental officers. |
| 8 | Painting two coats with ready mixed plastic emulsion paint of First class quality of approved colour etc., over plastered surface including priming coat and cost and conveyence of all meterials etc., complete as per standard specification. |
| 9 | Painting two coat with synthetic enamel paint of approved quality and colour over new iron work including cost and conveyence of all meterials & labour including cost of primer coat charges etc.,complete. |
| 10 | Supplying, delivery and fixing of HDPE tank 1000 lit capacity as per IS 12701/1996 including all cost and conveyance of all materials etc, complete, as per standerd specifiacation. |
| 11 | Supply of 15 lpmx 100 m Head wet type 1 phase bore well submersible motor with pump set with out panel boards as per IS 8034 including cost of tranportation of materials etc,complete as per standared specification. |
| 12 | Supply and erection of single phases panel Board for 1.5 HP etc. complete as per standared specification. |
| 13 | Supply and fixing of 32mm Heavy duty UPVC Column Pipe theraded pipe of approved quality including cost and conveyance etc., complete |
| 14 | Supply of 2.50 Sq.mm PVC insulated and sheathed 3 core flat type copper cable conforming to IS 694/1990 including all cost and conveyance of all materials etc complete. as per standard specifications.(WD-M1974) |
| 15 | Supply and fixing of 32Amps DP switch of 500V with metel clad with fuse and neutral (side Handle) on suitable TW Board with earth connection only. (M-1366) |
| 16 | Wiring with 2x4sq.mm. PVC insulated SC unsheathed FRLS copper conductor cable of 1100V grade in suitable pipe on wall and ceiling with PVC accessories with 150mmx100mmx113mm TW switch box for 15A 3pin non interlocking wall socket with 15A flush type switch with painting of suitable colour with continuous earth wire connection of 4sq.mm copper wire for open PVC power plug point (SD 39) |
| 17 | Supply fixing of Power capacitor for Power factor improvement with oil filled with discharge resistence 3 phase 415 / 440 volt HZ conforming to ISS 2384 with ISI marking.(M-1615) |
| 18 | Supply and run of 2 of 4 sq.mm PVC insulated SC unsheathed CU.Conductor of 1100 V in 25 mm dia GI Pipe (Glass - B) suitably bent at ends with neccessory angle iron upright and end supports for mains. (SD 70) |
| 19 | Supply and run of 2 of 4 sq.mm PVC insulated SC unsheathed CU.Conductor of 1100 V on 7/20 GI bearer wire for Service Connection Mains. (SD 65) |
| 20 | Supply and fixing of TNEB meter Board suitable for 32A Single phase service connection with 32A fuse unit (500V) 32A neutral link and Earth link (1”x 1/8” copper flat) on TW plank of size 375mmx300mmx19mm with supporting TW repairs of 1” thick on either side with painting with suitable bolt and nuts for fixing TW plank on wall with earth connection and inter connection with 7/20 PVC insulate copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Higher End) with suitable necessary connection (SD 125) |
| 21 | Supply and fixing of single phase 16 Amps Porcelain Fuse Unit (500V) |
| 22 | Supply and delivery of 32 mm GI pipe of B class of approved quality including all cost and conveyance etc, complete, as per standerd specifiacation. (WD-M0487) |
| 23 | Supply of 40mm UPVC pipe including all cost and conveyance etc, complete, as per standerd specifiacation. (PWD SOR 25-26 M-1087) |
| 24 | Supply and fixing of 32mm G.I. pipes, 40mm UPVC pipe and Water supply specials etc., complete as per standard specification. - 32mm Bore clamp |
| 25 | Bore Cover Plate |
| 26 | 32mm GI Elbow.WD-M0594 |
| 27 | 32mm GI Union.WD-M0603 |
| 28 | Gun Metal Wheel Valve (Heavy Duty) 32mm dia(PWD SOR 25-26 M-0504) |
| 29 | 32mm Gate valve |
| 30 | 32mm GI coupling |
| 31 | 32mm GI Tee |
| 32 | 32 mm GI Nipple - 300mm |
| 33 | 32mm GI Bend |
| 34 | 20mm GI Bend |
| 35 | 20mm GI Tee |
| 36 | 20mm GI Elbow |
| 37 | 20mm GI Nipple - 300mm |
| 38 | 20mm GI Nipple - 150mm |
| 39 | Brass Chromium Plated Screw Down Tap20mm dia (Heavy Type). (MW-M0230) |
| 40 | 32mm CI flange set |
| 41 | 32mm GI Dummy |
| 42 | 40mm UPVC Elbow |
| 43 | 40mm UPVC TEE |
| 44 | 40mm UPVC Coupling |
| 45 | UPVC Reducer 40mm x 32mm dia (PWD SOR 25-26 M-1143) |
| 46 | UPVC Reducer 32mm x 25mm dia (PWD SOR 25-26 M-1144) |
| 47 | UPVC Reducer 25mm x 20mm dia (PWD SOR 25-26 M-1145) |
| 48 | PVC Screw Down Tap Heavy Type 20mm dia (PWD SOR 25-26 M-0510) |
| 49 | Gun Metal Check Valve (32mm)(MW-M0213)) |
| 50 | 32mm dia GI cutting |
| 51 | 32mm dia GI pipe Threading |
| 52 | Laying of 32mm G.I. Pipes, 40mm UPVC pipe and specials to proper line and level including jointing but excluding cost of pipes and jointing materials for plumbing works for providing water supply and sanitary works in the premises of the building |
| 53 | Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth ,valves erection clamps,pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, voltmeter,Ammeter, three pilot(indicating)lamps capacitor single phasing preventor, water level guard and laying and jointing the caple and twin earthing as per IE rules extra complete and testing the pumpset and trail run for ten days. |
| 54 | Labour charges for the removel of deep well hand pumps from bore well etc., complete Please Enable Macros to View BoQ information |
