|
| 1 | Excavation in foundations,trenches etc in earth work in all kind of soil, such as pick work, jumper work, blasting hard or soft rock by chiselling where the blasting work is prohibited slushy daldal and saturated soil including pumping or bailing out water with in all heights, stacking the excavated soil within all leads clear from the edge of excavation and then returning the stacked soil in 15cm(fifteen centimetres) layers, when required into plinths, sides of foundations etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth, as per the direction of Engineer-in-Charge with in all leads and lifts. |
| 2 | Providing and laying Cement concrete 1:6:12 (1 Cement:6 Sand:12 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth complete in all respect including all leads and lifts. |
| 3 | Random rubble masonry/polygenal rubbe masonry ( un-coursed/bright to courses) with hard stone of approved quality in foundation and plinth including levelling up with C.M 1:6:12 (1cement:6 sand :12 graded stone aggregate 20mm nominal size) in CM 1:6 (1cement: 6sand in breast wall & retaining walls complete in all respect including all leads and lifts. |
| 4 | Ist class Brick work using common burnt clay building bricks in super structure above plinth level upto floor two level in cement mortor 1:6 (1cement:6sand), with in all leads and lifts. |
| 5 | Providing wood work in frames of doors, windows,clerestory windows and other frames wrought ,framed & fixed in position :1st class Deodar wood in all respect i/c all leads & lifts. as per the direction and satisfection of the Engineer in charge. |
| 6 | Providing 40x3mm flat iron hold fasts 40cm long i/c fixing to frames with 10mm. diameter bolts nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm in CC 1:3:6 (1cement:3sand: 6 graded stone aggregate 20mm nominal size) complete in all respect with in all leads and lifts. |
| 7 | Providing form work with steel plates 3.15 mm thick welded with angles iron in frame 30 x 30 x 5 mm so as to give a fair finish including centering shuttering struting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor two ceiling not exceeding 4 meters and removal of the same for in-situ- reinforced concrete and plain concrete in: |
| 8 | Flat surfaces such as soffits of sunspended floor, roofs landings and the like floors etc upto 200mm thickness. |
| 9 | Beams,cantilevers,girders & lintels etc. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 mtrs. In depth in all heights from floor complete in all respect including all leads and lifts. |
| 10 | Edges of slab and breaks in floor and walls under 20cm wide |
| 11 | Providing and laying cement concrete work 1:2:4(1cement:2sand:4graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work: |
| 12 | In suspended floor roofs,landings, shelves and their supports balconies, beams girders bressumers and centilevers upto floor two level i/c carriage of material within all leads and lifts. |
| 13 | Providing and fixing panelled,glazed or panelled and glazed shutters for doors, windows and clere storey windows including black enamelled iron but hings with necessary screws 40mm thick in 1st class Deodar wood with in all leads and lifts. |
| 14 | Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-Charge. within all leads and lifts. |
| 15 | 40mm thick cement concrete flooring 1:2:4(1cement:2sand:4graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement (base concrete to be paid for seperately) i/c all leads and lifts. |
| 16 | 6mm thick cement plaster to ceiling in CM 1:3 (1cement:3 sand) with in all leads and lifts. |
| 17 | 20mm cement plaster in single coat on rough side of brick\stone masonary for interior plastering up to floor two level including arrises, internal rounded angles, chamfers and\or rounded angles not exceeding 80mm in girth and finished even and smooth in C.M 1:6 (1 Cement :6 Sand) with in all leads and lifts. |
| 18 | 15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in C.M 1:6 complete in all respect as per the dircetion and to the entire satisfaction of Engineer in charge within all leads and lifts. |
| 19 | Applying priming coat over new wood and wood based surfaces after and including preparing the surfaces by thoroughly cleaning oil grease dirt and other foreign matter, sand papering and knotting, ready mixed paint brushing wood primer pink complete in all respect with in all leads and lifts. |
| 20 | Painting two coats (excluding priming coat) on new wood and wood based surface with ready mixed paint brushing to give an even shade including cleaning of all dirts,dust and other foreign matter sand papering and stopping with ready mixed paint other than white complete in all respect. |
| 21 | Applying priming coat over new concrete/masonry/asbestos/cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required with ready mixed primer complete in all respect as per direction and to the entire satisfaction of Engineer- in- charge within all leads and lifts. |
| 22 | Distempering with oil bound distemper of approved brand and manufacture (two coat) and of required shade on decorated wall surface to give an even shade on over and i/c priming coat with distemper of approved brand and manufacture after thouroughly brushing the surface free from mortar droppings and other foreign matter complete in all respect. |
| 23 | Providing Mild steel/tor steel reinforcement for RCC work including bending, binding and placing in position complete upto floor two level (tor steel) complete with in all leads and lifts |
| 24 | Providing and fixing Aluminium sliding door bolts anodized transparent or dyed to required colour and shade with bolts and nuts screws etc complete with in all leads & lifts. |
| 25 | 300x16mm |
| 26 | Providing and fixing Aluminium Tower bolt (barrel type) anodized transparent with necessary screws etc complete in all respect |
| 27 | 200x10 mm |
| 28 | 100x10 mm |
| 29 | Providing and fixing Aluminium handles anodized transparent or dyed to required colour or shade with screw etc complete in all respect. |
| 30 | 125mm |
| 31 | 100mm |
| 32 | Boulder filling dry hand packed tightly under the floor / damaged portion of kuhl complete in all respect with in all leads and lifts. |
| 33 | Providing and fixing M.S. gril of required pattern in wooden frames of window s etc. with M. S. flats square or round bars with round headed bolts and nuts or by screws plain grills with in all leads and lifts. Please Enable Macros to View BoQ information |
