|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering including carriage of material in all leads & lifts. All work up to plinth level. |
| 2 | 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 3 | 1:2:4(1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 4 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level Cement mortar 1:4 (1 cement :4 coarse sand) including carriage of material in all leads and lifts. |
| 5 | Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, frames and fixed in position including carriage of material in all leads and lifts.(a) Ivory coast teak Wood |
| 6 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including carriage of material in all leads and lifts. |
| 7 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 8 | 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws |
| 9 | Providing & fixing 35mm thick single/double leaf fully glazed window shutters made of 1st class ivory coast teak wood having styles & top rail & bottom rail 75mm width and chamferred edged beading 20x12mm for glass panes complete including bright finished/black enamelled iron butt hinges with necessary screws including carriage of material in all leads and lifts. |
| 10 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. Complete including carriage of material in all leads and lifts. |
| 11 | Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately) including carriage of material in all leads and lifts. 18 mm thick |
| 12 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) including carriage of material in all leads and lifts |
| 13 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete including carriage of material in all leads and lifts. |
| 14 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete including carriage of material in all leads &lifts. |
| 15 | Providing and fixing stainless steel sliding door bolt transparent or dyed to required colour and shade with bolts, nuts and screws etc. complete including carriage of material in all leads & lifts. |
| 16 | 300x16 mm |
| 17 | 250x16 mm |
| 18 | Providing and fixing stainless steel tower bolt (barrel type) annodized transparent or dyed to required shade and colour with screws etc. complete including carriage of material in all leads & lifts. |
| 19 | 250x10 mm |
| 20 | 150x10 mm |
| 21 | Providing and fixing stainless steel handles annodized transparent or dyed to required colour or shade with necessary screws etc. complete including carriage of material in all leads & lifts. |
| 22 | 125 mm |
| 23 | 100 mm |
| 24 | Providing and fixing Stainless steel hook & eyes with necessary screws or welding to chowakat including carriage of material in all leads and lifts.150mm. |
| 25 | Providing and fixing Stainless steel floor door stopper with necessary screws etc. complete including carriage of material in all leads and lifts. |
| 26 | Providing and fixing magnatic catcher of approved quality in cupboard/ Ward robe shutters including fixing with necessary screws etc complete including carriage of material in all leads and lifts. Double strip hrizontal type. |
| 27 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. including carriage of material in all leads and lifts. |
| 28 | Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer- in-charge including carriage of material in all leads and lifts. |
| 29 | Providing and fixing sliding arrangement in racks/ cupboards/ cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately) including carriage of material in all leads and lifts. |
| 30 | Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive etc. complete in all rescects as per manufacturers specifications and direction of the Engineer-in-Charge including carriage of material in all leads and lifts. |
| 31 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer including carriage of material in all leads and lifts |
| 32 | Structural steel work riveted, bolted or welded in built up sections, Trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of material in all leads and lifts. In gratings, frames, guard bar, ladder,railings, brackets, gates and similar works |
| 33 | Providing and fixing Ist quality digital glazed wall tiles conforming to IS: 15622 (thickness thicknes not less than 8mm), of approved make, in all colours, shades of any size as approved by Engineer-in-Charge i/c cost for cutting the tiles whwrever required, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete including carriage of material in all leads & lifts. |
| 34 | Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant of any size & colour manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads & lifts. |
| 35 | Providing and laying vitrified floor tiles as per sample approved by the Engineer-in-Charge(thickness not less than 10mm) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of material in all leads & lifts. |
| 36 | Providing and laying Vitrified tiles as per sample approved by the Engineer-in-Charge (thickness not less than 8mm thick)with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including carriage of material in all leads & lifts. |
| 37 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes i/c carriage of material in all leads and lifts. 110 mm diameter (Finolex/ Supreme) |
| 38 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion i/c carriage of material in all leads and lifts(Finolex/ Supreme) |
| 39 | Bend 87.5° 110 mm bend |
| 40 | Shoe (Plain) 110 mm Shoe |
| 41 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete i/c carriage of material in all leads and lifts. 110 mm |
| 42 | 6 mm cement plaster to ceiling of mix 1:3 (1 cement : 3 fine sand) including carriage of material in all leads and lifts. |
| 43 | 15 mm cement plaster on the fair side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) including carriage of material in all leads and lifts. |
| 44 | 20 mm cement plaster on the rough of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) on rough side wall including carriage of material in all leads & lifts. |
| 45 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete including carriage of material in all leads and lifts |
| 46 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat withcement primer including carriage of material in all leads and lifts. |
| 47 | On Wall |
| 48 | On Ceiling. |
| 49 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications including carriage of material in all leads and lifts. |
| 50 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture |
| 51 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture |
| 52 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives including carriage of material in all leads and lifts. New work (Two or more coats applied @1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
| 53 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge including carriage of material in all leads and lifts. With cement mortar 1:4 (1 cement : 4 fine sand) |
| 54 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. Complete including carriage of material in all leads and lifts. |
| 55 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge including carriage of material in all leads and lifts. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 56 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead including carriage of material in all leads and lifts. Of area 3 sq. metres and below |
| 57 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead including carriage of material in all leads and lifts. Of area 3 sq. metres and below |
| 58 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead including carriage of material in all leads and lifts. For thickness of tiles 10 mm to 25 mm |
| 59 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge including carriage of material in all leads and lifts. |
| 60 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) including carriage of material in all leads and lifts. |
| 61 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 62 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 63 | Providing and fixing prelaminated partical board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge. 18 mm thick |
| 64 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item) including carriage of material in all leads and lifts. |
| 65 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) |
| 66 | With float glass panes of 8 mm thickness (weight not less than 20 kg/ sqm) |
| 67 | Supplying and fixing expended metal (size 25mmx25mmx1.8mm) to wood or steel members in partitions etc including carriage of material in all leads and lifts. Weight exceeding 3kg and not exceeding 5kg per Sq.M. |
| 68 | Providing and fixing 3mm thick aluminium composite panel (ACP) sheet fixed over 1\\"x1.5\\" aluminium section for cladding on exterior walls upto all level/height including necessary screws and sealing material complete in all respects including carriage of material in all leads |
| 69 | Supplying and fixing 12mm thick swing Toughened Glass door with necessary fitting as required etc complete in all respets including carriage of material in all leads and lifts. |
| 70 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall including carriage of material in all leads and lifts. |
| 71 | 15 mm dia nominal bore |
| 72 | 20mm nominal bore |
| 73 | Providing and laying in trenches, galvanised mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) including carriage of material in all leads and lifts. |
| 74 | 15 mm nominal bore |
| 75 | 20mm nominal bore |
| 76 | Making connection of galvanised steel distribution branch with galvanised mild steel main 25mm to 40 mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of material in all leads and lifts: |
| 77 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required Including carriage of material in all leads & lifts. W.C. pan with ISI marked white solid plastic seat and lid |
| 78 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete Including carriage of material in all leads & lifts. 10 litre capacity - White |
| 79 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Including carriage of material in all leads & lifts. Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 80 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required but excluding fittings Hindware/ Cera make including carriage of material in leads and lifts. White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 81 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. including carriage of material in all leads & lifts. |
| 82 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of material in all leads and lifts 1000 litres net capacity storage tank of ISI marked sintex make with double.layer including MS Stays for water storage tank. |
| 83 | Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc.complete including carriage of material in all leads and lifts |
| 84 | 90 mm nominal size. |
| 85 | 110mm nominal size. |
| 86 | Providing and fixing PVC Plain bend ISI marked complete i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts |
| 87 | 90mm nominal size. |
| 88 | 110mm nominal size. |
| 89 | Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc.complete including carriage of material in all leads and lifts |
| 90 | 90mm nominal size. |
| 91 | 110mm nominal size. |
| 92 | P/F PVC Single equal branch ISI marked of required degree with oval access door insertion rubber washer 3mm thick bolts and nuts complete i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts |
| 93 | 90mm nominal size. |
| 94 | 110mm nominal size. |
| 95 | Providing and fixing PVC Collar i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts |
| 96 | 90mm nominal size. |
| 97 | 110mm nominal size. |
| 98 | Providing and fixing (ISI marked) PVC cowl i/c fixing with approved adhensive etc complete including carriage of material in all leads and lifts. |
| 99 | 90mm nominal size. |
| 100 | 110mm nominal size. |
| 101 | Providing and fixing (ISI marked) PVC floor trap of self cleaning design i/c fixing with approved adhensive with C.P. screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors including carriage of material in all leads and lifts.110x90 mm |
| 102 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS standards and weighing not less than 690 gms..15mm dia |
| 103 | Long Body |
| 104 | Short Body |
| 105 | Providing and fixing C.P. Brass angle valve 15 mm without/with nuts Including carriage of material in all leads and lifts.15 mm dia |
| 106 | Providing and fixing CP soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. Including carriage of materia in all leads and lifts. |
| 107 | Providing and fixing 100 mm dia chromium plated grating of superior quality for floor, gully or nahani trap i/c carriage of material in all leads & lifts. |
| 108 | Providing and Fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Including carriage of material in all leads and lifts. Flexible pipe 32mm nominal bore |
| 109 | Providing and Fixing 600mmx450mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers including carriage of material in all leads & lifts. |
| 110 | Providing and Fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. Including carriage of material in all leads and lifts. |
| 111 | Providing and fixing toilet paper holder including carriage of material in all leads and lifts. C.P. Brass |
| 112 | Providing and fixing M.I Union for Wash basin & Sink Including carriage of material in all leads and lifts. 32mm nominal bore |
| 113 | Providing and fixing C.P. brass waste for wash basin or sink including carriage of material in all leads & lifts. 32mm dia |
| 114 | Providing and fixing C.P. brass towel ring with Plastic Gitti, Drilling hole etc complete in all respects Including carriage of material in all leads and lifts. |
| 115 | Providing and fixing PVC connection pipe Including carriage of material in all leads and lifts. 15mm dia 45 cm. length. |
| 116 | Providing and fixing G.I./M.I Union of following sizes (Where not included in the items.Including carriage of material in all leads and lifts. |
| 117 | 15mm nominal bore |
| 118 | 20mm nominal bore |
| 119 | Providing and fixing 8 mm dia C.P. / S.S. health faucet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 120 | Cutting holes through existing brick work including making good the same in cement mortar 1:6 (1 cement: 6 sand) per CMs depth of cutting (i) Holes upto and including 400 sqcm in area including carriage of material in all leads and lifts |
| 121 | Providing chases 75mm wide 50mm deep (average size) in walls for conduit pipes and filling the same with cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregate 20 mm and down gauge) after the conduit pipe is laid (excluding the cost of conduit pipe) including carriage of materialin all leads and lifts. |
| 122 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 123 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads & lifts. Inside size 90x80 cm and 45 cm deep including S.F.R.C. manhole frame and cover (medium duty) 560 mm internal diameter, total weight of cover and frame to be not less than 173 kg (weight of cover 70 kg and weight of frame 103 kg) with 230mm thick walls of common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 124 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete including carriage of material in all leads and lifts. For pipes 100 to 250 mm diameter |
| 125 | Supplying and fixing glass panes with putty and nails including removal of broken glass panes wherever necessary including carriage of material in all leads and lifts. Plain Glass 4 mm thick. Please Enable Macros to View BoQ information |
