|
| 1 | Electronics and Communication Engineering Lab Materials |
| 2 | DSO (Digital Storage Oscilloscope)Bandwidth: 50 - 100 MHz.Sampling Rate: 1GS/s.Channels: 2 (minimum)Power Supply: 100V–240V AC, 50-60 HzAutomatic Measurement: Vpp, Vavg,RMS, Frequency, Period, Vmax, Vmin, Rise Time, Fall Time, + Width, - Width, +Duty, - Duty etc.,Horizontal Scale: 5 ns/div – 100 ns/div or equivalentVertical Resolution: 8 bits (2 Channels simultaneously)Vertical Sensitivity: 1 mV/div – 10 V/div (at input)Waveform Math: +, -, x , ÷, invert, FFT etc.,Waveform Storage: 16 waveforms or equivalentCommunication Interface: USB Host, USB interface.7-inch color display or equivalentBasic trigger functions |
| 3 | Digital IC trainer kit With Breadboard5V DC, 1A regulated power supply±12V DC / ±15V, 200 mA regulated power supplySolderless breadboard to accommodate 8 × 16-pin ICsZIF (Zero Insertion Force) IC socketsSupports TTL and CMOS ICsLogic IO LEDs for output monitoring8 buffered LED outputs8 debounced switch inputsTTL clock: 1 MHzVariable clock generator: 0.5 Hz to 50 HzSingle pulse output: 100 ms (buffered, positive and negative outputs)One seven-segment display with 4 BCD inputsBuilt-in logic probesBuilt-in logic switchesExperiments on basic logic gates, flip-flops, counters, and multiplexers |
| 4 | Eliminator Transformer (stepdown)Input - 220V - 240V AC, 50 Hz, Output-2V to 12V DC, 0-2 A Ripple: <5mV |
| 5 | Decade resistance boxRange: 1 Ω to 10 MΩ, steps: 1-10-100-1k-10k, accuracy ±1%, suitable for filter and oscillator experiments |
| 6 | DECADE INDUCTANCE BOXRange: 1 µH to 10 H, rotary switch selection, low loss inductors, accuracy ±1%, , suitable for filter and oscillator experiments |
| 7 | 8051 Micro controller KitOperating Voltage: +5V DC4 KB Flash (AT89C51) / 8 KB Flash (AT89S52)RAM: 128 Bytes internal RAM16×2 Alphanumeric LCDPush Buttons / Tactile SwitchesDIP Switches for digital inputInbuilt ADC Interface : LDR,POTInbuilt DAC InterfaceInbuilt Stepper Motor Driver With Stepper MotorInbuilt DC Motor Driver with DC Motor1X4 Led Array, 1 X4 Keypad, 1X Relay1X Buzzer, 16X2 LCD Display, 1X PWM Driver1X Hardware Interrupt Key, Inbuilt RTCInbuilt EEPROM, Inbuilt UART Module4X7 Segment Display, Both Assembly and C language programmable, PC Interfaceable. |
| 8 | Single Phase Induction MotorSingle phase induction motor, 230V AC, 50Hz supply.Power rating 1 HP (0.75 kW).Speed 1440 RPM.Capacitor start/run type suitable for lab useLoading Setup portable ammeter and Digital Tactometer contact type |
| 9 | Auto TransformerInput - single-phase, 230V/240V, 50 Hz, 4A, AC Output - 0 to 270VAC, Class \\"H\\" or Class F insulation. |
| 10 | TEMPERATURE MEASUREMENT KITSensors: RTD (PT-100), Thermocouple (Fe-K/J-type), and/or Thermistor (NTC).Display: 3½ digit LED/LCD digital display (typically 200mV FSD).Temperature Source: Portable water kettle or heater block.Signal Conditioning: On-board circuitry for amplification, linearization, and cold junction compensation. Test Points: Multiple 2mm/4mm banana sockets for monitoring input/output signals.Power Supply: 230V AC, 50Hz, Single-phase.Accessories: Includes a glass thermometer, NTC thermistor probe 10k, K-type thermocouple probe, patch cords, and instruction manual. |
| 11 | Ask modulation and Demodulation kitMessage Signal 1 : 8 Bit variable Data, Amplitude 5VMessage Signal 2 : Debounce Data, Amplitude Low (0) & High (5V)Message Signal 3 :Fixed Data 25K, 12.5K, 6.25K, 3.12K, Amplitude 5VCarrier Signal : Sine wave Frequency 200 KHz, Amplitude 5VModulator Type : Switching ICDemodulator : Envelope Detector & LPFComparator : LM 311 BasedSupply Voltage (Board) : +12V, +5V / DCSupply current : 100 mA (Minimum)Input Voltage : 230 V/ 50 Hz ACInterface connectors : 2mm banana socket |
| 12 | DTH trainer kitPower supply 200V to 240v AC, 50Hz,Dish Antenna 1.5' Aluminum steerable, LNB Low Noise Block down converterInput frequency KU band.Output frequency 950 to 1450 MHz.Conversion gain 65 dB.Noise Temp 35 degree K max.SET TOP BOX Receiver in Trainer FormIF frequency 70 MHz.Video Bandwidth 50 Hz to 5 MHz.Video output level 1 Vpp at 75 ohm loadVideo polarity Normal and or Inverted Switch selectableAudio sub carrier frequency Tunable from 5.0 to 8.0 MHz.R.F Output channel No 2 Uplink satellite INSAT 4AControls Channel selecting, Volume, Faults 5 No.PCB Size 15\\"x12\\" with Block diagram in multicolor section wise Standard accessoriesDish Antenna1.5 feet,LNB,Trainer PCB,Dish connecting wire,Audio-Video cable,Teaching manual,Acrylic cover.Hardware Material for assembly of dish antenna.DTH Subscription Connection DoorDarshan Free Channels. |
| 13 | Fiber Optic Communication Trainer KitFiber optic trainer supporting analog, digital and voice communication using LED/lasersource with photodiode receiver and plastic/glass fiber.Facilities for experiments on attenuation, bandwidth, numerical aperture, digital modulationand voice transmission.Includes transmitter–receiver modules, fiber cables, power supply, patch cords anddetailed experiment manual. |
| 14 | SIM reader trainer kitSIM Compatibility Supports 2G 3G 4G LTE SIM cards,SIM READER Mode: Reading Writing GSM SIM card data, IMSI, KI codes, phonebookInterface USB 2.0 or RS 232 Serial Port for PC communication.Clock Frequencies: Selectable frequencies 3.579 MHz, 7.159 MHz, 14.318 MHz for SIM card operation.Power Supply: Onboard SMPS 12V 2A or 5V DC with overload protection.Hardware Components:6-pin or 8 pin SIM card socket.LED indicators for power, SIM reset, and data activity.Optional LCD 128x64 and Keypad 20 keys for standalone operation.Software Tools Support for AT commands GSM ETSI 07.0707.05, SIM Manager utilities, and data logger functionality. Common Trainer Kit FeaturesFault Simulation Ability to create faults e.g., SIM not detected, Vcc failure for troubleshooting.Test Points: Multiple test points e.g., 55 nos for observing signals SIM RST, CLK, I O via oscilloscope.Construction Tested Glass Epoxy PCB, often housed in a study educational case. |
| 15 | FPGA Trainer Kit• FPGA-based trainer using Xilinx/AMD Artix-7 or Spartan series, USB-JTAG programmable, compatible with Vivado /ISE (WebPACK).• On-board peripherals: LEDs, switches, push buttons, 7-segment display, clock source, GPIO / Pmod expansion ports.• Includes power supply, USB cable, programming support,and lab manual with sample experiments. |
| 16 | FPGA / SoC Development BoardFPGA fabric: mid-range, ~85K–100K logic cells, 220+ DSP slicesIntegrated dual-core ARM Cortex-A processorOn-board DDR3/DDR3L memory ≥ 512 MBPeripherals: USB, Ethernet, HDMI (in/out), general-purpose I/OExpansion: Pmod and standard headers for sensors/modulesProgramming & Debug: USB JTAG, microSD supportPower: 5 V or 12 V DC inputSupports HDL (Verilog/VHDL), C/C++ , embedded Linux,occasional PythonUse case: hardware/software co-design, acceleratorprototyping, embedded research Please Enable Macros to View BoQ information |
