|
| 1 | Charges for repairing of leakage in UPVC / HDPE pipe line with PVC coupler & solvent cement etc. including necessary earth excavation, backfilling of soil as required after laying of pipeline, in layers not exceeding 200 mm in depth including consolidating each deposited layer by ramming, watering etc. complete as per specification & direction of the Engineer-in-charge. |
| 2 | i) 90 mm OD |
| 3 | ii) 110 mm OD |
| 4 | iii) 140 mm OD |
| 5 | Clearing of diposited iron inside of laid PVC pipe line (90 mm/110 mm / 140 mm) excavation trenches for 100.00 mtr laid pipe line of required width and depth at an interval of 2.00 mtr to 3.00 mtr long for every 100.00 mtr. Clearing through UPVC coil pipe and laying same with coupler and cement solvent joint (PVC coupler and solvent cement to be issued at free of cost from the department) |
| 6 | Clearing of diposited iron inside of laid CI/DI pipe line of different dia (150 mm/100 mm / 125 mm) and dismantling including trenching, refilling for every 100.00 mtr laid pipe line of required widht and depth, cutting for every 100.00 mtr pipe iron throug PVC coil pipe after clearing washing and laying the same with rubber gusket pipe layed joint as per direction of the Engineer-in-charge. (Pig lead will be issued by the department at free of cost but rubber gusket and other T&P will be arranged by the agency) |
| 7 | Dismantling old C.I. / D.I. pipes including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes at site lead upto 50 metre as per CPWD specification and direction of the Engineer - in - charge. |
| 8 | i) 80 mm dia |
| 9 | ii) 100 mm dia |
| 10 | iii) 150 mm dia |
| 11 | Providing and fitting fixing Tyton joint, collar including fitting fixing of MS flat, square bar rubber gasket of appear quality alongwith painting with anticonosive litumastic black paint and fitting fixing of nut and bolts etc. including necessary excavating of trenches refilling etc. complete as required as per CPWD specification and direction of the Engineer-in-charge. |
| 12 | i) 80 mm dia |
| 13 | ii) 100 mm dia |
| 14 | iv) 150 mm dia |
| 15 | Charges for dismantling PVC / HDPE pipe after necessary excavation of earth including washing and stacking of pipes properly at site with all leads and lifts and backfilling of soil as required after laying of pipeline, in layers not exceeding 200 mm in depth including consolidating each deposited layer by ramming, watering etc. complete as per specification & direction of the Engineer-in-charge. |
| 16 | i) 90 mm dia |
| 17 | ii) 110 mm dia |
| 18 | iii) 140 mm dia |
| 19 | Providing, fixing and laying fabricated UPVC bend of required degree conforming to IS : 10124 ( part 8 / 9 / 10 / 11 / 12 / 13 ) with solvent cement conforming to IS : 14182 including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 20 | i)40 mm dia |
| 21 | i) 90 mm dia |
| 22 | ii) 110 mm dia |
| 23 | Providing, fixing and laying fabricated UPVC end cap conforming to IS : 10124 ( Part 4 ) with solvent cement conforming to IS : 14182 including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 24 | i)40 mm dia |
| 25 | i) 90 mm dia |
| 26 | ii) 110 mm dia |
| 27 | Excavating trenches of required width for pipes, cables etc. including exacavation for sockets, dressing of sides where required, ramming of bottoms, depth upto 1500 mm (slope-1 in 200)including getting out the excavated soil and backfilling of soil as required after laying of pipeline, in layers not exceeding 200 mm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil with all required leads as per Chapter - 2 of CPWD specification and direction of the Engineer - in - charge.A) For UPVC pipes in new work a) In all kinds of soil i) For pipes not exceeding 90 mm dia |
| 28 | Providing and fixing C.I. sluice valves ( with cap ) complete with bolts, nuts, rubber insertions etc. ( the tail pieces if required will be paid separately ) as per CPWD specification and direction of the Engineer - in - charge. |
| 29 | iii) 80 mm dia.A) PN - 1.6 |
| 30 | iv) 100 mm dia.A) PN - 1.6 |
| 31 | v) 125 mm dia.A) PN - 1.6 |
| 32 | vi) 150 mm dia.A) PN - 1.6 |
| 33 | Constructing masonry Chamber 90x90x100 cm,inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluicevalve, with C.I. surface box 100 mm. topdiameter, 160 mm bottom diameter and 190 mm deep (inside) with chained lid and RCC top slab 1:2:4mix (1 cement : 2 coarse sand : 4 graded stoneaggregate 20 mm nominal size ) necessaryexcavation foundation concrete 1:5:10 (1 cement : 5 fine sand:10 graded stone aggregate 40 mmnominal size ) and inside plastering with cementmortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :i) With Second Class bricks |
| 34 | Providing and laying of flexible PVC pipe (conforming to IS:7634) complete as per specification and direction of the Engineer - in - charge (cost of earth work and fittings will be paid separately). i)15 mm dia |
| 35 | Providing and fixing brass ferrule with C.I. cover conforming to IS : 2692 including boring and tapping the main as per CPWD specification and direction of the Engineer - in - charge.i)10 mm nominal bore |
| 36 | Providing and fixing G.I. Nipple of medium class as per CPWD specification and direction of the Engineer - in - charge.i)15 mm dia 150 mm long |
| 37 | Making road crossing by horizontal boring for smooth laying of UPVC / CI / DI / GI pipes etc. of required dia complete as per specification and the direction of the Engineer-in-charge. i)by manual means |
| 38 | Providing and fixing G.I. Bend /elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. i)15 mm dia |
| 39 | Providing and fixing G.I. socket as per CPWD specification and direction of the Engineer - in - charge. i)15 mm dia |
| 40 | Providing and fixing G.I. union as per CPWD specification and direction of the Engineer - in - charge. i) 15 mm dia |
| 41 | Charges for making hole by drilling and making thread by thread bit in the CI / DI pipe as per specification & direction of the Engineer-in-charge. i)10 mm dia nominal bore |
| 42 | Providing and fitting fixing PVC / plastic bib cock conforming to IS : 9763 in hydrant points at different location as per specification & direction of the Engineer-in-charge. i)15 mm dia PVC /plastic bib cock |
| 43 | Providing and fixing G.I. pipes medim class as per IS : 1239 with latest amendment complete with G.I. fittings including trenching and refilling, cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in - charge. A. External work.i)15 mm dia. nominal bore Please Enable Macros to View BoQ information |
