|
| 1 | Revised rate of timer 2024 SITC of single phase 110 Amp/115 Amp 3 pole 230 V contractor and digital time switch automatic timer for on/off system of Make LandT/CandS/Legrand complete wiring and component fitting. The job including all material, labour, erection satisfaction of Engineer-in-Charge. |
| 2 | Supply and erection of electrical meter i.e. 7 kw, 3-Phase for Decorative Lights cetagory as per UHBVN standard and specifications. |
| 3 | Supply and erection of electrical meter i.e. 6 kw, 3-Phase for Decorative Lights cetagory as per UHBVN standard and specifications. |
| 4 | Supply and erection of 7meter double arm decorative pole , duly PU Painted as per required RAL color code double arm as per photo of design (enclosed). The decorative pole should be in two sections, bottom section shall be a polygonal/tapered type with min. 4mm thick and 3 meter in length, having a top dimension of 150 mm across flats, a bottom dimension of 240 mm across flats, and a wall thickness of 4 mm, made out of IS 2062/ E355A or equivalent. It shall be provided with a 350 × 350 × 25 mm thick base plate for proper anchoring and stability, and supplied complete with 4 nos. foundation bolts of M20 × 700 mm length, including nuts, washers, and a fixing template to ensure accurate positioning during installation. The upper section with double arms shall be 5.5 meter in vertical height, fabricated from 60 mm diameter GI pipe (IS 1239) with min. 2.9 mm thickness, and both arms shall be reinforced at the joint with a 4 mm thick MS sheet plate to provide structural strength, rigidity, and a balanced decorative appearance. The complete pole assembly shall be protected against corrosion and finished for durability by means of a four-stage painting process consisting of a first coat of etch primer, a second coat of epoxy primer, a third coat of polyurethane (PU) paint of approved shade, and a final fourth coat of clear polyurethane. This treatment will not only provide long-term corrosion resistance but also give the pole an elegant decorative finish, making it suitable for outdoor, urban, and architectural applications. bottom part must have duly stress fit gate with backalite sheet suitable to fix MCB for internal wire connection. Pole should be suitable to install 2nos. LED luminaire over both decorative arm with Supply of 60W LED Street Light made of single piece aluminium die cast min. 60W with min. 130lm/w system efficacy with optimum distribution to ensure adequate required lux levelon site alongwith Supply of 120W LED Street Light made of single piece aluminium die cast min. 130lm/w system efficacy with optimum distribution to ensure adequate required lux levelon site. Make: Mayfair/Translighting/Vak Lighting. Note: Warranty of Pole and Light against any manufacturing defect is 5 years. The warranty pereiod shall be started from the date of completion of project |
| 5 | [23.22.1.9]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.9. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA [Through Rate] |
| 6 | [23.22.2.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 2.1. MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings MCCB up to 125 A FP [Through Rate] |
| 7 | [23.22.5.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole [Through Rate] |
| 8 | [23.27.1]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 1. M.S. pedestal of size 600 mm wide , 750 mm high ,300 mm deep and bottom totally open , duly embeded in 1:2:4 cement concrete block of size 750 mm x 450 mm x 200 mm above ground level , having a base of size 900 mm x 600 mm x 250 mm below ground level. 0 0 [Through Rate] |
| 9 | [23.3.6.1]COPPER WIRING IN PVC CONDUIT (SURFACE/RECESS) 6.1. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) [Through Rate] |
| 10 | [24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. [Through Rate] |
| 11 | [24.1.11]EARTHING AND LIGHTENING ARRESTOR 11. Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required. [Through Rate] |
| 12 | [24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required. [Through Rate] |
| 13 | [24.11.32]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING AND ERECTION/LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR CABLE 0.75 METER BELOW GROUND LEVEL COVERED WITH SAND AND BRICKS INCLUDING EXCAVATION AND REFILLING OF TRENCHES 32. 25 Sq mm 4 core (Arm.) [Through Rate] |
| 14 | [24.14.9]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 9. 6 Sq mm 3 core (UnArm.) [Through Rate] |
| 15 | [24.2.8.5]LT CABLE 8.5. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 25 sqmm [Through Rate] |
| 16 | [24.5.2.3]MISCELLANEOUS ITEMS 2.3. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia [Through Rate] |
| 17 | [24.8.5]RCC FOUNDATIONS FOR OCTAGONAL POLES 5. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 7m high pole [Through Rate] Please Enable Macros to View BoQ information |
