|
| 1 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 2 | S & F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 3 | S&F Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 4 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 5 | S&F for steel work in tubular section for purlin/rafters etc including special shaped washer etc. complete using induction butt welded tubes conforming to I.S. 1161-1998 grade St- 240 complete all as specified and directed. |
| 6 | S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc gde Fe-410 W (Gde E- 250) quality A complete all as specified and directed. |
| 7 | M&L for applying two coat of Synthetic enamal paint over a coat of red oxide primer on new steel based surfaces exc.10cm width or girth including preparation complete all as specified and directed. |
| 8 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets complete all as specified and directed. |
| 9 | S&F for aluminium anodised snap grid frame work of size 605mm x 605mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing two coats of distemper oil emulsion complete all as specified and directed. |
| 10 | Taking down chowkats or frame, n. exc 1.5 sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed. |
| 11 | Taking down chowkats or frame, n. exc 1.5 sqm each with shutters (without taking off shutter from the frame) for steel/Al window complete all as specified and directed. |
| 12 | Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exe 1.50 & n.exc. 4 sqm in each complete all as specified and directed. |
| 13 | M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, cooler stands (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floor in PCC 1:2:4 type B-0 to match the existing floor complete all as specified and directed. |
| 14 | S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification and drawing complete all as specified and directed. |
| 15 | S & F factory made solid panel PVC door shutter, 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded, plain colour PVC \\"C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as per specification and drawing and complete all as specified and directed. |
| 16 | S&F 75 mm size stainless steel butt hinges medium weight cold rolled complete all as specified and directed. |
| 17 | Supply and fix for 150mm long aluminium handles, cast type, anodised complete all as specified and directed. |
| 18 | Supply and fix for 150mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed. |
| 19 | S&F pressed steel door frame 125x60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates comlete as specified and directed (pcc filling of holloow section measured and paid seprately) complete all as specified and directed. |
| 20 | S&F pressed steel door frame 105x60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates comlete as specified and directed (pcc filling of holloow section measured and paid seprately) complete all as specified and directed. |
| 21 | M&L PCC 1:3:6, C-1 (using 20 mm graded stone aggregate) as in bed blocks for inserting holdfast/ filling of steel frame, etc including necessary form work complete all as specified and directed. |
| 22 | S&F 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides Ditto, but with particle board core complete all as specified and directed. |
| 23 | S & F 35 mm thick, 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers all complete as specified and directed. |
| 24 | S & F 35mm thick, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a) complete all as specified and directed. |
| 25 | S&F powder coated aluminium anodised frame for doors, windows etc with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 26 | S&F aluminium anodised powder coated (minm thickness of powder coating 50 micron) door shutters , aluninium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neopriene paccking, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed. |
| 27 | S&F Anodised aluminium powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. |
| 28 | Supply and fixing of aluminium sliding window with powder coating (minium thickness of powder coating 50 micron) including following components / specification complete all as specified and directed. (i) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (ii) All vercal/ horizontal joint shall be of extruded aluminium section so as to avoid any play between jointed members. (iii) all other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, srews, etc. (iv) Stainless steel wire cloth, 036 mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples, etc. (v) Sheet glass 4 mm thick selected quality tinted/black glass and glazing with oil putty or fixed with wooden beads in square not exceeding 0.5 Sqm in each pane (vi) Rest all as specified in drawing no CEZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5, 5R/5. Note :- Grill shall be measured and paid separately. |
| 29 | Supply & fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete all as specified and directed. |
| 30 | Supply and fix s/s butt hinges 100mm long cold rolled medium weight complete all as specified and directed. |
| 31 | Supply and fix 150mm long mild steel pressed handles, oval type, stove enameled black complete all as specified and directed. |
| 32 | S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm long complete all as specified and directed. |
| 33 | S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 150mm longcomplete all as specified and directed. |
| 34 | Supply and fix 250mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed. |
| 35 | S&F door closer hydraulically regulated, designation No. 3, aluminium (Die cast) body, universal type (ISI marked), complete all as specified and directed. |
| 36 | S&F brass mortice lock, vertical type, size 65mm, 2 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified and directed. |
| 37 | S&F in repairs door closer hydraulically regulated, designation No. 3, aluminium (Die cast) body, universal type (ISI marked), complete all as specified & as directed. |
| 38 | S&F in repairs brass mortice lock, vertical type, size 65mm, 2 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified and directed. |
| 39 | Supply only sheet glass ordinary quality,in squares exc. 0.5 SQM each 4.80 mm thick complete all as specified and directed. |
| 40 | Supply only sheet glass ordinary quality,in squares n. exc. 0.5 SQM each 4.80 mm thick complete all as specified and directed. |
| 41 | S & F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.. |
| 42 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete as specified and directed. |
| 43 | S & F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each panes.complete all as specified and directed. |
| 44 | M & L MS flat iron work as in hold fast and similar small articles, cut to length, bent to shape, drilled hole and fixed with screw etc conforming to Fe-290 Gde-E-165 complete as specified and directed. |
| 45 | M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165 complete all as specified and directed. |
| 46 | Taking down Cupboard Shutters of Any description exc 1 Sqm and n exc 2 Sqm complete all as specified and directed. |
| 47 | S & F 18/19mm pre-laminated particle board interior grade prelaminated both side with decorative choice lamination fixed with screws to timber frame work as in shutter of cup board and other similar work |
| 48 | S & F Width of flaps (when open) 40mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 49 | Supply and fix 150mm long mild steel pressed handles, oval type, stove enameled black complete all as specified and directed. |
| 50 | S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm long complete all as specified and directed. |
| 51 | S & F mild steel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 150mm long complete all as specified and directed. |
| 52 | Supply and fix 250mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed. |
| 53 | S&F in repairs 300 mm long aluminium alloy anodised sliding door bolt with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section of cast aluminium and fixed complete all as specified and directed. |
| 54 | S&F in repairs Extruded aluminium alloy handle, fabricated type, anodised, 125mm size, (ISI marked) complete all as specified and directed. |
| 55 | S&F as in repairs 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 56 | Supply and fixing in repairs butt hinges 100 mm long medium weight cold rolled MS fixed in repairs to wooden or pressed steel/angle iron frames by welding complete all as specified and directed. |
| 57 | S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed overall length 140 mm complete all as specified and directed. |
| 58 | Welding in repairs not exceeding 6mm thick and not exceeding 2.5 cm in length complete all as specified and directed. |
| 59 | M & L preparation of new untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 60 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 61 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed. |
| 62 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed. |
| 63 | M & L 25 mm thick PCC type B0 1:2:4 (using 12.5 mm graded stone aggregate) as in leveling complete all as specified and directed. |
| 64 | M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed. |
| 65 | M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed. |
| 66 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm (400X400X7mm) in floor, over 15mm thick screed bed in CM 1:4 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and directed. |
| 67 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile not exceeding 0.11 sqm in floor, over 15 mm thick screed bed in CM 1:4 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and directed. |
| 68 | M&L for glazed ceramic tiles in vertical surface 300x450x7mm thick in dado over 10mm thick screed bed in CM 1:4 on walls set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed |
| 69 | M & L 75 mm thick PCC type D-2 1:4:8 ( using 40mm graded stone aggregate) as in sub base complete all as specified and directed. |
| 70 | M&L for prepolished, chequered cement concrete tiles of size 25cmx25cmx22mm thick, as in floors etc, including 15 mm thick screed bed or bedding in cement mortar (1:6) and set and jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed. |
| 71 | M&L Pre-cast (Factory casted) cement concrete Kerb stone casted in PCC (1:2:4) Type B-1 using 20mm graded stone aggregates with plan or interlocking joints (as directed) with solid blocks, exc. 10 cm in width and setting and jointed in cement mortar 1:6, complete all as specified and directed. |
| 72 | Demolition of brick work built in cement mortar complete all as specified and directed. |
| 73 | M & L brick work with sub class 'B' bricks straight or curved in plan exc 6 mtr mean radius built in CM (1:4) using old size bricks complete all as specified and directed. |
| 74 | M & L brick work with sub class -B old size bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:6 complete all as specified and directed. |
| 75 | Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 76 | M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 including WPC and finished the surfaces even and smooth without using extra cement as specified and directed.(Note : WPC shall be measured separately) |
| 77 | M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 78 | M & L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceilings (sunshade, chajja etc) and finished the surfaces even and fair without using extra cement complete all as specified and directed. |
| 79 | Supply only liquid water proofing compound complete all as specified and directed. |
| 80 | M & L for preparing newly plastered surfaces of wall and applying two coats of white wash complete all as specified and directed. |
| 81 | M & L for preparing new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 82 | M & L for applying two coats of distmper oil emulsion over coat of primer including wall care putty on walls after preparing surfaces of walls on newly plastered wall surfaces including preparation of surfaces.complete all as specified and directed. |
| 83 | M&L for complete removal of exisiting treatment of wall and applying two coat of oil bound distemper over 1mm thick wall care putty of Birla white or JK & Primer complete all as specified and directed. |
| 84 | M&L for preparation of old decorated plastered or unplastered surfaces of wall, cornices etc by brooming down or steel wire brushing, scrapping down, smoke soot, moulds, moos efflorescent and trading oil and greasy spots and applying two coat of cement base paint (white or tinned) complete all as specified and directed. |
| 85 | M&L preapring old plastered surfaces incl washing rubbing down and stopping of distempered and painted surface of ceiling and applying one coat of white wash complete all as specified and directed. |
| 86 | Taking up or down 15mm steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed. |
| 87 | Refixing 15mm old steel tubing and connection in new or old position (wall, ceiling, floors, etc.) complete all as specified and directed. |
| 88 | S & F steel tubing 15mm bore medium grade galvanised with all fittings and fixed complete to wall, ceilings or laid in floors all as specified and directed. |
| 89 | Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed. |
| 90 | Refixing 20mm old steel tubing and connection in new or old position (wall, ceiling, floors, etc.)complete all as specified and directed. |
| 91 | S & F steel tubing 20 mm bore medium grade galvanised with all fittings and fixed complete to wall, ceilings or laid in floors complete all as specified and directed. |
| 92 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good , cutting not exc 10cm girth complete all as specified and directed. |
| 93 | S&F in repairs for MS grating CP 75/100mm dia, with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as specified and directed. |
| 94 | S&F in repairs for towel rails of 20mm dia tubular brass chromium plated 60cm long 'D' type fixed to all as directed by Engr-in-charge including taking down existing towel rail complete all as specified and directed. |
| 95 | S & F in repairs 15 mm bore Bip taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 96 | S & F in repairs, 15 mm bore, bib tap, PTMT (PVC) with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 97 | S & F in repairs, stop valves, 15 mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 98 | S & F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and directed. |
| 99 | S&F in repairs health faucet cast copper alloy with push button flexible steel pipe with PVC lining of 1 mtr long suitable for 15mm pipe complete all as specified and directed. |
| 100 | S&F in repair soap dish of stainless steel fixed to wall with chromium plated brass screws complete all as specified and as directed |
| 101 | S&F Towel ring CP (Cat Part No T6904A1 of make – Parryware or equivalent of Jaquar/Marc) complete all as specified and directed. |
| 102 | S&F in repairs flexible (coil shaped) PVC waste pipe for sink and wash hand basin 32/40mm dia, length not less than 70 cm, connected to PVC waste coupling/fittings complete all as specified and directed. |
| 103 | S & F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified directed. |
| 104 | S & F in repairs Vitreous china wash basin, white,flat back, size 550 x 400 mm with brackets,excluding pillar cock 15 mm bore CP, PVC connection of 450 mm long including PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as specified and directed. |
| 105 | S&F in repairs Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed. |
| 106 | S & F in repairs, 15 mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 107 | S & F in repairs, swivel shower rose of PTMT, 15mm bore (minimum weight 40 gms) including shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (minimum wt 40 gms) complete all as specified and directed. |
| 108 | S&F in repairs plastic water closet seat cover white closed pattern with flat bottom and mild steel CP or aluminium hinging device complete all as specified an directed. |
| 109 | S&F for Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) front or back inlet including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, etc and making good to floor complete as in repair complete all as specified and directed. |
| 110 | S&F in repair for Vitreous China urinals, half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing grating and Union for discharge pipe incl CP 40mm waste coupling and PVC 40mm waste pipe 900mm long complete all as specified and directed. |
| 111 | S&F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed. |
| 112 | S & F in repairs, vitreous China squatting pan, 'Orissa' pattern, size 580mm x 440 mm, white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and directed. |
| 113 | Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water tanks complete as specified in SSR Part-I complete all as specified and directed. |
| 114 | Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water tanks complete as specified in SSR Part-I complete all as specified and directed. |
| 115 | S & F in repair 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) complete all as specified and directed. |
| 116 | S&F as in repairs for Gun metal gate valves with iron wheel headscrewed both ends for iron pipes or for unions for 20 mm bore pipes, complete all as specified and directed. |
| 117 | Servicing of steel rolling shutters of area upto 21 sqm (single opening) of lever operated with rectification of minor defects, overhauling, greasing, lubricanting of guide rails and refixing clamps, rivetting including necessary repairs to the locking arrangements and replacement of wornout spare parts such as gear/worm/interlocking laths/ball bearing in order to bring the rolling shutters to easy operation and smooth funtioning all as directed by the Engr-in-Charge.. Note:- The Spare parts will be measured and paid for separately and rate quoted is deemed to include for fixing of spare parts complete all as specified and directed. |
| 118 | M & L for preparation of old steel and iron surfaces of rolling shutter of any description over 10cm width or girth and Priming with zinc chromium and two coat of aluminium paint up to 8 mtr height complete all as specified and directed |
| 119 | M & L for preparation of new steel and iron surfaces of rolling shutter of any description over 10cm width or girth and Priming with zinc chromium and two coat of aluminium paint up to 8 mtr height complete all as specified and directed |
| 120 | Greasing only of rolling shutters including guide channels of area up to 21 Sqm of area complete all as specified and directed. |
| 121 | S & F in repairs 1mm thick hood cover of hexogonal, square or circular contour depending on the contour of bracket plates properly stiffened with angle / flat stiffener at top and bottom edges complete all as specified and directed. |
| 122 | S & F in repairs 50mm bore MS pipe for suspension shafts for rolling shutter complete all as specified and directed. |
| 123 | S & F in repairs bevel gear box for rolling shutters v |
| 124 | S & F in repairs crank handle for operating gear operated rolling shutters complete all as specified and directed. |
| 125 | S & F main spring 'O' gauge 450mm long of approved make complete all as specified and directed. |
| 126 | Supply only interlocking lath sections made out of cold rolled steel strips of 1.2mm thick and 75mm width complete all as specified in SSR complete all as specified and directed. |
| 127 | Welding in repairs exc 2.5cm but n. exc 5cm in length to the thickness of metal to be welded exc. 6mm but n. exc 9mm sheets/plates/any other steel members, incl cleaning and preparing the surfaces while welding, and bevelling of edges as required complete all as specified and directed. |
| 128 | S & F Steel rolling shutters, with out ball bearing, as specified.Thickness of laths is 1.25 mmincluding top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed. |
| 129 | All as above Item No 128, but gear operated type with bevel gear box and crank handle complete all as specified and directed. |
| 130 | S & F safety lever locks mild steel 4 levers for rolling shutters complete all as specified and directed. Please Enable Macros to View BoQ information |
