|
| 1 | Earthwork in excavation in cutting in hard soil within the initial lead and lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3 mtr in depth etc complete as per the direction of the Engineer in Charge. |
| 2 | Earthwork in excavation in foundation in all kinds of soil within the initial lead and lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3 mtr in depth etc complete as per the direction of the Engineer in Charge. |
| 3 | Plain Cement Concrete M10 Grade using 40mm down graded chips in Foundation and Plinth |
| 4 | Plain Cement Concrete M15 Grade using 40mm down graded chips in Foundation and Plinth |
| 5 | Reinforced Cement Concrete M 30 Grade using 20mm down graded chips in Foundation and Plinth In Foundation |
| 6 | Abutment & Pier Shaft |
| 7 | DIRT Wall |
| 8 | Pier & Abutment cap |
| 9 | Retaing wall/wing wall |
| 10 | Wearing Coat |
| 11 | Approach Slab |
| 12 | Deck Slab |
| 13 | RCC Crash barrier of M40 Grade |
| 14 | Providing HYSD bars confirming to approved grade F-415 including all labours for cutting ,bending, binding, lapping, splicing, welding etc. (conforming to ISI specification) & jointing if necessary by lapping & tying the grills & placing in position as required for RCC works as per the approved design, hoisting, lowering & laying position including cost & conveyance of tor steel & binding wires of 18 to 20 gauge (as to be approved by the Deptt.) etc. complete with Cess in all respect (weight of binding wire shall not be considered for payment at all which will be borne by the contractor) as per specification and direction of the Engineer in charge. |
| 15 | Providing and laying of Filter media with stone crushed aggregates of 45mm size satisfying the requirements laid down in clause 2504.2.2 of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surfact behind abutment,wing wall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specification & direction of Engineer-in Charge. |
| 16 | Providing weep hole in plan / Reinforced concrete abutment, wing wall / retaining wall with 100mm dia A.C. Pipe, extending through the full width of the structure with slope of 1V : 20 H towards drawing face complete as per drawing and technical specification and direction of Engineer in charge. |
| 17 | Providing Rough stone dry packing / pitching in slope, protection walls, approns and revetments to designed thickness using hard granite stones of required size of approved quality from approved quarry including quarrying supplying conveying and cost conveyance taxes royalty of all materials including T&P complete including filling the interstices with small stones by wedging and hammering finished to proper slope and level as per direction of the Engineer in charge including dewatering if required. |
| 18 | Supplying & filling behind abutment, wing wall and return wall etc with approved quality of gravel / sandy material including watering to complete saturation & ramming complete with all leads & lifts including cost. Conveyance royality & taxes of all materials & cost of all labour & T&P required for the work complete ( measurement will be taken for compacted section as per direction of Engineer-in-Charge.) Granular Material (GRAVEL BACKING) |
| 19 | SANDY MATERIAL |
| 20 | Sandy Material (Below Raft) |
| 21 | Supplying and fixing of RCC Guard post of 150 mm dia and 1.00 M long in RCC (1:2:4) using 20mm down graded size h.g chips including all labours, materials ,carriage ,royality & taxes of etc. complete. |
| 22 | Providing , fitting , fixing expansion joint confirming to ISI specification including all cost , carriage , taxes etc complete as per specification & direction of Engineer-in-Charge Fixing of Strip seal Expansion Joint |
| 23 | Fixing of Salitax Board |
| 24 | Providing, fitting & fixing of Drainge spout etc |
| 25 | Cement concrete (1:3:6) in foundation & plinth with 4cm. crusher broken granite metal of approved quality from approved quarry including hoisting lowering & laying in layers not exceeding 150mm. thick with proper packing & ramming each layer of concrete by means of vibrator ,providing groove & beads where necessary including curing, dewatering, shoring, shuttering if necessary at the time of laying concrete with cost, conveyance royality & taxes of all material required for the work including supplying & working pumps, T&P articles finishing the exposed surface smooth as per specific ation & direction of the Engineer-in Charge |
| 26 | Providing, laying tar papers of approved quality confirming to ISI specification above pier & abutment caps to receive concreting for slab casting including all cost , carriage & taxes etc complete as per specification & direction of Engineer-in-Charge |
| 27 | Providing and applying two coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescense and applying paint @ 1 litre per 02 Sqm |
| 28 | Providing & fixing of SBY Information board |
| 29 | Construction of embankment with approved material obtained from borrow pits with 5 extra lead lifts and leads, transporting to site by mechanical means within a lead of 5kms, spreading, grading to required slope and compacting to meet requirement of table 300-2 & clause 305 of MoSRT&H Specifications for Road & Bridge works (4th Revision)and as per the direction of engineer in charge. |
| 30 | Loosening of the ground up to a level of 500mm below the sub-grade level , watered , graded & compacted in layers to meet requirement of table 300-2 for sub-grade construction & clause 305 of MORTH specification of Road & Bridge works ( 4th Revision ) |
| 31 | Construction of granular sub-base by providing Close graded Granular subbase Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (4th Revision) |
| 32 | Providing, laying, spreading & compacting graded stone aggregate to Wet Mix Macadam specification including pre mixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, laying in uniform layers with paver in sub base/base course on well prepared surface & compacting with vibratory roller to acieve the desired density as per clause 406 of MoSRT & H specifications for road & bridge works.(4th Revision) |
| 33 | Providing and applying primer coat with bitumen emulsion (SS) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means as per Technical Specification Clause 502 of MOSRT&H including cost, conveyance, royalty, taxes of chips and bitumen & other required materials etc. complete and as per direction of Engineer-In-Charge. |
| 34 | Providing and applying Tack coat with bitumen emulsion on prepared surface including clearing of road surfaces and spraying primer @ 0.20kg/ sqm using Mechanical means as per clause 502 of MoSRT&H Specifications of Road & Bridge work (04th Revision) |
| 35 | Providing & laying Bituminous Macadam with hot mix plant using crushed aggregates of specified grading premixed with bituminous binder of 60/70 penetration grade of bitumen, transported to site, laid over previously prepared surface with hydrostatic paver finisher with sensore control to the required grade, level & alingment & roling with smooth wheeled,vibratory & tandem rollers to achieve the desire compaction as per clause 504 of MoSRT&H Specifications for road and bridge works (4th Revision) Page-169 Item -45 |
| 36 | Providing & laying Semi Dense Bituminous Concrete with batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder of 60/70 penetration grade of bitumen, transporting the hot mix to site, laying with a hydrostatic paver finisher with sensore control to the required grade, level & alingment, roling with smooth wheeled,vibratory & tandem rollers to achieve the desire compaction as per clause 508 of MoSRT&H Specifications for road and bridge works (4th Revision) Page -175 item - 47 |
| 37 | Fine dressing & Turfing with initial lead of 50 mtr. and initial lift of 1.50 mtr.. |
| 38 | Filling sand-Supplying & filling good clean river sand of approved quality including watering to complete saturation & ramming complete with all leads & lifts including cost, conveyance, royalty & taxes of all materials & cost of all labour & T&P required for the work etc. complete as per specification & direction of Engineer in charge. |
| 39 | P.C.C-M-15using 40mm size H.G.metal well rammed with cost, Conveyance , royality,taxes of all material and labour,T & P etc.Complete. |
| 40 | Providing laying R.C.C. Hume pipe NP3 class for culverts including fixing collar with cement mortar 1:2 but excluding excavation, protection work, backfilling,concrete and masonry work in head walls and parapets clause 1106 of MORD specification for Rural roads and as per irection of Engineer-in charge.1000 mm dia |
| 41 | Plain cement concrete M-15 grade in Foundation complete as per drawing and technical specification. |
| 42 | Plain cement concrete M-15 grade in Sub-Structure complete as per drawing and technical specification. Please Enable Macros to View BoQ information |
