Name of Work:- Supply of Equipment for Electronics and Cmmunication Engineering Department: (as per Specification And NIT)
Sl. No.
Item Description
1
Supply of Equipment for Electronics and Cmmunication Engineering Department
2
8051 Micro controller Kit :SPECIFICATION :• Operating voltage: +5 V dc.• Flash memory: 4 kB (AT89C51) / 8 kB (AT89S52).• RAM: 128 bytes internal RAM.• 16 × 2 alphanumeric LCD display.• Push buttons / tactile switches.• DIP switches for digital input.• Inbuilt ADC interface: LDR, potentiometer.• Inbuilt DAC interface.• Inbuilt stepper motor driver with stepper motor.• Inbuilt DC motor driver with DC motor.• 1 × 4 LED array, 1 × 4 keypad, 1 × relay.• 1 × buzzer, 16 × 2 LCD display, 1 × PWM driver.• 1 × hardware interrupt key, inbuilt RTC.• Inbuilt EEPROM and UART module.• 4 × 7-segment display.• Supports both Assembly and C language programming.• PC interfaceable.
3
TEMPERATUREMEASUREMENTKITSPECIFICATION :• Sensors:RTD (PT-100), Thermocouple (Fe-K/J-type), and/orThermistor (NTC).• Display: 3½ digit LED/LCD digital display(typically 200 mV FSD).• Temperature source: Portable water kettle orheater block.• Signal conditioning: On-board circuitry foramplification, linearization, and cold junctioncompensation.• Test points: Multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals.• Power supply: 230 V ac, 50 Hz, single-phase.• Accessories: Glass thermometer, 10 k NTCthermistor probe, K-type thermocouple probe,patch cords and User manual.
4
Ask modulationandDemodulation kit:SPECIFICATION :• Message Signal1:8-bit variable data,amplitude 5V.• Message Signal 2:Debounced data, amplitude low (0) and high (5 V).• Message Signal 3:Fixed data 25 kHz, 12.5 kHz, 6.25 kHz, 3.12 kHz,amplitude 5 V.• Carrier signal: Sine wave, frequency 200 kHz,amplitude 5 V.• Modulator type: Switching modulator using analogswitch / transistor switching IC.• Demodulator: Envelope detector and LPF.• Comparator: LM311 based.• Supply voltage (board): +12 V, +5 V dc.• Supply current: 100 mA minimum.• Input voltage: 230 V ac, 50 Hz.• Interface connectors: 2 mm banana socket.
5
DTH trainer kit:SPECIFICATION :Power Supply:• 200 V to 240 V ac, 50 Hz.Dish Antenna:• 1.5 ft aluminium steerable dish antenna.LNB (Low Noise Block Down Converter): • Input frequency: Ku-band.• Output frequency: 950 MHz to 1450 MHz.• Conversion gain: 65 dB.• Noise temperature: 35 K (max).Set-Top Box Receiver in Trainer Form:• IF frequency: 70 MHz.• Video bandwidth: 50 Hz to 5 MHz.• Video output level: 1 Vpp at 75 Ω load.• Video polarity: Normal/Inverted, switch selectable.• Audio subcarrier frequency:Tunable from 5.0 MHz to 8.0 MHz.• Remote control provided.• HDMI cable: 10 m.Controls:• Channel selection.• Volume control.Fault Simulation:• Five built-in simulated faults for troubleshootingexperiments.• IF signal disconnected.• Video output fault.• Audio mute fault.• Tuner misalignment.• RF output interruption.PCB Size:• 15\\" × 12\\" with multicolour section-wise blockdiagram.Standard Accessories:• 1.5 ft dish antenna.• LNB.• Trainer PCB.• Dish connecting wire.• Audio-video cable.• User manual.• Acrylic cover.• Hardware materials for assembly of dish antenna.Additional Features:• DTH subscription connection withDoordarshanfree channels. • Free-to-air channel demonstration.
6
FPGA Trainer Kit:SPECIFICATION :• Must use industry-standard mid-range FPGAdevice• USB-JTAG programmable, compatible withVivado ISE (WebPACK).• Power supply: 5 V DC through USB or externaladapter.• On-board peripherals: LEDs, switches, pushbuttons, 7-segment display,clock source, GPIO /Pmod expansion ports, UART, VGA / HDMI, USBUARTbridge, USB cable.•User manual. Please Enable Macros to View BoQ information
We takes all possible care for accurate & authentic tender information, however Users
are requested to refer Original source of Tender Notice / Tender Document published by
Tender Issuing Agency before taking any call regarding this tender.
