|
| 1 | Item code morth 301 Excavtion in soil using hydraulics excavator and tippers with disposal upto 1000 meters Excavation for road work in soil with hydraulics excavator including cutting and loading in tippers, trimming bottom and side slopes in accordance with requiremements of lines , grades and cross section and transportation to the embankment location within all lifts and lead upto 1000 meters |
| 2 | Providing and laying in position cement concrete with 4 cm gauge approved stone ballast c sand and cement in pro of 8:4:1 including supply of all material labour tools and plants etc req for proper comp of work |
| 3 | centering & shuterring including strutting propping etc & removal of form for: Foundation , footing bases of colums etc for mass concrete |
| 4 | centering & shuterring including strutting propping etc & removal of form for: Lintels, beams, plinth beams, griders, bressumer sand cantiliver |
| 5 | centering & shuterring including strutting propping etc & removal of form for: Column, Pillers, Piers, Abutments, Posts and struts |
| 6 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level : 1:1.5:3 (1 cement: 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) DSR-18/5.1.2 |
| 7 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work upto plinth level : 1:1.5:3 (1 cement: 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) DSR-18/5.1.2 all work above plinth upto V level |
| 8 | Reinforcement for RCC work including straghtening cutting bending placing in position and binding all complete up to plinth |
| 9 | M-150 brick work in 1:4 cement & fine sand 1.25f.M mortar in foundation and plinth including supply of all materials labour complection of the work compiation of work 1:4 |
| 10 | M-150 brick work in 1:4 cement & fine sand 1.25f.M mortar Above plinth including supply of all materials labour complection of the work compiation of work 1:4 |
| 11 | 12mm Cement Plaster of mix 1:6 (1 cement : 6 coarse sand) |
| 12 | 15mm Cement Plaster of mix 1:6 (1 cement : 6 coarse sand) |
| 13 | Finishing walls with water proofing cement paint of required shade:New work Two or more coats applied 3.84 kg/bsqm |
| 14 | Providing precast cement concrete JaIl 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete excluding plastering of the jambs, sills and soffits. |
| 15 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 16 | Painting with synthetic enemel paint of approved brand and manufacture to give an even shade: Two or more coats on new work |
| 17 | Dry Brick on Edge flooring in required pattern wirh bricks of class designation 150 on bed of earth including filling compressed woth M-150 Brick |
| 18 | Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 (Based on SOR UP PWD 2020) |
| 19 | Providing and laving 60 mm thick factory made cement concrete Interlocking paver block(ISI Marked) made by block making machine with strong vibratory compaction of approved size design, shape, laid in required color and pattern over and including average 50 mm thick compacted bed coarse sand and filling the joints with fine sand all complete as per direction of Engineer -in - charge with conforming (UP PWD SOR 2020) (New SOR Based DAR 16.68) |
| 20 | Sit Up Station: Providing, designing and fixing of sit-up single tation of size 1500 x 1150 x 650mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe of 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat and base plate cover to be made up from virgin LLDPE manufactured by rotationalMolding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover nuts and bolts with the base plate.All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal) and fixing of equipments etc. (the cement concrete and excavation work shall be paid separately). |
| 21 | Leg Press: Providing, designing and fixing of leg press of size 2000 x 550 x 1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars to be provided with high quality grip rubber on top end. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact of injury. Seat and base plate cover to be made up from virgin LLDPE manufactured by rotational molding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movements. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 22 | Seated chest press: Providing, designing and fixing of seated chest press in a pair of size 1800 x 700 x 2000 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury. Seats and base plate cover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt and once the concrete is set, fix the equipment on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of Equipments etc (the cement concrete and excavation work shall be paid separately). |
| 23 | Arm wheel: Providing, designing and fixing of arm wheel in a pair of size 850 x 800 x 1800 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury and base platecover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 24 | Twister: Providing, designing and fixing twister of size 1700 x 1300 x 1300 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Foothold shall be made up of nylon alloy with rounded edges to prevent any impact or injury and base plate cover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 25 | Air Swing: Providing, designing and fixing of air swing in pair of size 1150 x 900 x 1250mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made of Nylon alloy with rounded edges to prevent any impact of injury and base plate cover to be made from virgin LLDPE manufactured by rotational molding with minimum thickness of plastic of 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movements. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the Equipment on to it and cover nuts and bolts with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc (the cement concrete and excavation work Shall be paid separately). |
| 26 | Horse rider station: Providing, designing and fixing of horse rider station of size 1000 x 600 x 1100 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact of injury. Base plate cover and seat to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt and once the concrete is set, fix the equipment on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate cover and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 27 | Elliptical exerciser: Providing, designing and fixing elliptical exerciser of size 1200 x 540 x 1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury and base plate cover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealedAnd self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). |
| 28 | Double cross walker: Providing, designing and fixing double cross walker of size 1600 x 600 x 1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury and base plate cover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover with the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing ofEquipments etc (the cement concrete and excavation work shall be paid separately). |
| 29 | Bridge Ladder: Providing, designing and fixing bridge ladder of size 2750 x 1000 x 1500 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80 - 120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Foothold shall be made up of nylon alloy with rounded edges to prevent any impact or injury and base plate Cover to be made up from virgin LLDPE manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolts and once the concrete is set, fix the equipments on to it and cover within the base plate. All complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). Please Enable Macros to View BoQ information |
