|
| 1 | Providing and fixing C.I sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) as per CPWD specification and direction of the Engineer - in - charge, |
| 2 | i) 150 mm dia. PN-1.0 |
| 3 | Charges for repairing of leakages in UPVC HDPE pipe line with PVC coupler & solvent cement etc inc necessary earth excavation, backfilling of soil as required after laying of pipeline in layers not exceeding 200 mm in depth inte consolidating cach deposited lay er by ramming, watering etc. complete as per specification & direction of the Engineer in-charge.i) 90 mm dia |
| 4 | ii) 110 mm dia |
| 5 | iii) 140 mm dia |
| 6 | Excavating trenches of required width for pipes, cables etc, inle excavation for sockets, & dressing of sides where required, ramming of bottoms, depth up to 1500 mm(slope-1 in 200) in/c getting out the excavated soil, & back filling of soil as required, after laying of pipeline, in layers not exceeding 200 mm in depth in/c consolidating each deposited layer by ramming, watering etc. & disposing of surplus excavated soil with all required leads as per chapter 2- of CPWD specification & direction of the of the Engineer-in-charge A. For UPVC pipes in new work |
| 7 | A. For UPVC pipes in old work |
| 8 | a. In all kinds of soil |
| 9 | i) For pipes not exceeding 90 mm OD |
| 10 | ii) For pipes exceeding 90 mm OD but not exceeding 300 mm OD |
| 11 | Removal of Blockage from existing distribution pipe line of all domestic as well as washing by inserting 40mm dia PVC coil pipe upto the length of 30.00 mtr by cutting of pipe at any depth including necessary de watering whenever required etc. complete as per direction of the Engg-in-charge. (Bitumen road cutting excavating earth and re filling the same sand filling cutting and reaying of pipes specials in/c lead joints will be separtely).. |
| 12 | Labour charge for jointing of HDPI PVC pipe line offall diameter with PVC coupler and cement solvent joint( work to be executed after removal of blockage) complete as per direction of the Engg-in-charge |
| 13 | Labour charge for lifting of 20,000/10,000/5000 GPI Capacity water lubricated vertical submerssible pump motor in/c 80ft column pipe assembly by heavy duty chain pully block as per the direction of the engineer in-charge |
| 14 | Labour charge for fitting, fixing and lowering of 20,000/10,000/5000 GPH Capacity water lubricated vertical submerssible pump motor in/c 80ft column pipe assembly by heavy duty chain pully block as per the direction of the engineer in-charge |
| 15 | Repair and maintenance of 5HP/ 7.5HP Motor suitable for 2500 GPH capacity submerssible pumpset / complete dismantling inc providing & fitting fixiing of PVC (IS: 8783-1978) insulated electro grade copper (IS: 613-1984) conductor winding in stator & all necessaty spare parts and reassembling the same including servicing of rotor & necessary trial run as per specification and direction of the engineer-in-charge. |
| 16 | Repair and maintenance of 10 1HP/12.5 HI Motor suitable for 5000 GPI capacity submerssible pumpset by complete dismantling in/c providing & fitting fixing of PVC (IS: 8783-1978) insulated electro grade copper (IS: 613-1984) conductor 2.00 winding in stator & all necessary spare parts and reassembling the same including servicing of rotor & necessary trial run as per specification and direction of the Engineer-in-charge |
| 17 | Providing & fabrication of column pipe including fitting fixing of G.I. flange by cutting the Gl pipe (conforming to IS: 1239 medium class) into 3.05 mtr. long and welding the same with GI flange as per specification and direction of the Engineer-in-charge (G.I. pipe will be provided by the agency at his own cost & risk). |
| 18 | i) For 65 mm dia G.I. pipe with 10 mm thick GI flange |
| 19 | Providing, fixing and laying rigid UPVC pipes conforming to IS: 4985 jointing with couplers, of same class conforming to IS : 10124 ( Pt-II ) with solvent cement conforming to IS : 14182including testing of joints complete ( but excluding the cost ofspecials like bend, tees etc. which will be paid separately ) as per CPWD specification and direction of the Engineer - in -charge.A. Class - 3 ( working pressure 6.0 kg / cm2) |
| 20 | i. 90 mm OD |
| 21 | ii. 110 mm OD |
| 22 | Supplying and fitting fixing of single phase motor Starter panel unit capacity Comprise With 2 pole Conductor Over load relay capacitor voltmeter, Ampsmeter. of BCH/ L&T make with necessary Copper wire etc. Complete & direction of the Engineer-in-Charge. |
| 23 | Providing and fixing G.I. pipes of medium class as per IS 1239, wit latest amendment complete wit Gl fittings in/c trenching and refilling cutting end making good the walls etc. complete as per CPWD specification and direction the of Engineer-in-charge. A. External work |
| 24 | 1) 40 mm N.B |
| 25 | Providing. fixing and laying rigid UPVC pipes conforming to IS 4985 jointing with coplers, of same class conforming to IS 10124(Pt-II) with solvent cement conforming to IS 14182 including testing of joints complete (but excluding the cost of specials like bend. tees etc. which will be paid separately) as per specification and direction of the Engineer-In-Charge.a) Class 3 (working pressure 6.0 kg/sqm) |
| 26 | i) 40 mm OD |
| 27 | Providing and fitting fixing of brass fullway valve with handle in the Gl pipe line including cutting, threading etc, complete. as per CPWD specification and direction. of the Engineer-in-charge.1) 40 mm dia |
| 28 | Providing and fitting fixing of moving iron type, range 0-100/0-200 amps, 96 mm x 96 mm size AC amps meter direct reading type (L&T/AE make) with selector switch and CT coil as a electrical instrument of the pannel board as per specification and direction of the Engineer-in-charge. |
| 29 | Lifting of submersible pump motor with delivery assembly by heavy duty chain pully after dismantling from delivery line and stacking properly as per direction of the Engineer-In-Charge. |
| 30 | Repair and maintainance of submersible motor suitable for submersible pump-set by complete dismantling in/c providing fitting and fixing of PVC(IS:8783-1978) insulated electro grade copper( IS:613-1984) conductor winding in stator and on necessary spare parts and reassembling the same in/c servicing of rotor and necessary trial run as per specification and direction of Engineer-in-charge.a) 40 mm dia with 15 mm. dia. Openingi) 2.0 HP motor suitable for 2000 GPH capacity submersible pump-set. |
| 31 | Labour charge for fitting fixing & laying of submersible pump motor set with delivery assembly 90 to 0° in/c refiting fixing with the delivery line etc. As per direction of the Engineer-In-Charge. |
| 32 | Providing and fitting fixing steel sheet enclosed switch fuse unit (suitable for DIN fuses), triple pole with Neutral Link (TPN), 415/500 Volt, L & T/Havells/BCH make etc. complete as per specification and direction of the Engineer-incharge.i) 63 amps |
| 33 | Providing and fitting fixing of Fully Automatic Star Delta type Motor starter (3 ph. 50 Hz. 415V, in Steel Sheet Enclosures with Contractors and Timer etc. complete suitable for submersible Pump L & T, BCH, ABB make as per specification and direction of the Engineer-in-charge.i) 25 HP/18.5 kw Relay range within 13-21+10% |
| 34 | Providing and fitting fixing of moving iron type, range 0-500V, 96 mm x 96 mm size AC Volt meter (L&T/AE make) with selector switch as a electrical instrument of the pannel board as per specification and direction of the Engineer-in-charge. Please Enable Macros to View BoQ information |
