|
| 1 | Schedule-A |
| 2 | Taking down chowkhat or frames with shutters (without taking off shutters from the frame) n.exc. 1.5 Sqm each all as specified and as directed. |
| 3 | All as per Srl Item No. 1 above Ditto but exceeding 1.50 sqm each and n.exc. 4 Sqm each |
| 4 | Taking down shutters only exc 1 Sqm and n.exc. 2 Sqm each |
| 5 | S&F 2nd Class hard wood, plain solid, straight chowkhats and frames, wrought, framed repated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 6 | S&F Pressed steel frames for doors, size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc., complete, as specified, and directed by Engr-in-Charge. |
| 7 | S&F Pressed steel frames for doors, size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc., complete, as specified, and directed by Engr-in-Charge. |
| 8 | S&F Second class Hard wood 35 mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to Chowkhats all as specified and dircted by Engr-in-Charge. |
| 9 | S&F for 35 mm thick flush shutters, solid core construction, with block board and both faces are covered with 0.90 mm thick decorative face veneer with lipping/ frame to match, complete, fixed to chowkats all as specified and directed by Engineer-in-Charge. |
| 10 | M&L Second class hardwood 35 mm thickness, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I Section - 8 clause 8.24 (a) supplied and fitted to chowkhat. |
| 11 | S&F aluminium colour powder coated door Frame and shutter single or double leaf glazed/pre laminated particle board interior panels fabricated including aluminium powder coated beading rubber Gasket and packing materials and shall be drilling in existing wall and thrust bolt suitable size complete comprising the following:- (a) Door frame section 101.60x44.45x1.93 mm fixed as per spd (b) Door Shutter Vertical Style of Size 85x44.45x2 mm as per spd. (c) Door Shutter Top style section 95.25x44.45x2.00 mm as per spd. (d) Aluminium coloured powder coated middle lock rail/bottom rail section 150x44.45x1.93mm cat No.20002. (e) Aluminium coloured powder coated Tower Bolt 02 Nos in each shutter 200 mm long as spd. (f) Aluminium coloured powder coated handle 02 Nos in each shutter 150 mm long as per spd. (g) Door Floor spring ISI Marked Make-Sandhu, Amar or equivalent.(h) Six lever mortice lock brass on in each door.(j) 12 mm thick partical board (pre laminated both face) exterior grade ISI Marked (k) Tinted glass/Plain glass/half frosted/ full frostred (Colour) 5mm thick. |
| 12 | S&F aluminium coloured power coated (shade or tint as directed by GE) Side Hung window/ventilator frame and Shutter with section as per TD-109/2012 sheet (1/4 to 4/4) comprising the following:- (a) Al coloured powder coated window frame section 101.60x44.45x1.93 mm fixed as per spd(b) Aluminium coloured power coated double shutter (Glass and Wire Mesh shutter) 44x44x1.50mm top/bottom/sides style. (c) Aluminium coloured power coated butt hinges 8 Nos in each window 100 mm sizes as per spd. (d) Aluminium coloured power coated tower bolt 3 Nos in each window 150 mm long as per spd.(e) Aluminium coloured power coated handle 2 Nos in each window 100 mm long as per spd.(f) Tinted/coloured glass 5 mm thick fixed to window with rubber gasket & Al Powder coated beading. (g) Aluminium coloured power coated grill make deco grill DG-104 fixed with \\"H\\" Section. Note : If ground requirement for sliding window/AC window contractor should provide as per direction of Engineer-in-Charge without any price adjustment. |
| 13 | Providing and fixing powder coated aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 14 | S&F steel windows with glazing bars, side hung shutters with projecting type hinges, including steel handle, and steel peg stay dovetailed or welded ,complete in all respect as specified and directed. |
| 15 | S&F PVC door frame of size 50x47mm with a wall thickness of 5mm made out of extruded 5mm rigid prelaminated PVC foam sheet mite cut at two corners and jointing with 2 Nos of 150mm long brackets of 15x15mm MS square tube of two vertical door profiles are to be reinforced with 19x19mm MS square tube of 19 guage WPDM rubber gasket weather seal tobe provided throughout frame the door frame shal be fixed to the wall using 100mm long MS screws through the frame by using PVC fastners. A minimum of 04 Nos screws to be provided for each vertical members and minimum 02 Nos of horizontal members,Make:-Rajshri,Sintex or Equivalent. |
| 16 | S&F for 30mm thick factory made solid panel prelaminated PVC door shutter consisting of frame made out of MS tube of 19 guage thickness and size of 19x19mm for styes and 15x15mm for topo and bottom rails. MS frame shall have a coat of steel primer of approved make and manufacturer. MS frame adhered with 5mm thick heat moulded PVC `L' channel of size 30x75mm forming styles and 5mm thick, 100mm wide PVC sheet for top rail lock rail and bottom rail on either side and 5mm thick 20mm wide PVC sheet as gap inserted for top rail and bottom rail. panelling of 5mm PVC sheet to be fitted in MS frame to the styles and rails with 5mm thick 30mm wide PVC sheet beading on either side and jointed together with solvent cement adhesive etc complete all as specified and as directed by Engineer- in- Charge. |
| 17 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprisingof virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screwshaving minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ®Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.complete as per direction of Engineer-in-Charge. |
| 18 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 150 mm comprisingof virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screwshaving minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ®Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.complete as per direction of Engineer-in-Charge. |
| 19 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprisingof virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screwshaving minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ®Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.complete as per direction of Engineer-in-Charge. |
| 20 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm sizecomprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 21 | S & F Factory made single extruded WPC (Wood Polymer Composite) skeleton door solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, ater/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 22 | S&F Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm) Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). Tprofile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of'zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.)(A) Area not exceeding 1.00 sqm each |
| 23 | S&F Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm) Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). Tprofile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of'zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.)(A) Area exceeding 1.00 sqm but not exceeding 2.00 sqm each |
| 24 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi-chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality,& incluing taking down of old window of any description ,complete all as specified and directed by Engineer-in-Charge. |
| 25 | Dismantling structural steel work incl. steel door, gate, window guard bars, grills etc. including repair of surface with the existing surface complete all as specified and as directed by Engineer- in- Charge. |
| 26 | M&L fabricated frame work as in doors frame using MS Box section of required size for making rebate to fix Shutter and other section with gusset plate rails, braces etc. complete drilled for fixing Door Shutter with MS Butt Hinges and hole for tower bolt, sliding boltetc or other covering door etc to be prepared for hanging with and including hinges all as specified and as directed. |
| 27 | M&L for mild steel works as in grills and railing, hold fasts etc of Fe-410-0or Fe 310-0, complete all as specified and as directed by Engr-in-charge |
| 28 | M&L PCC for 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping, benching & for fixing railing, holdfast etc complete all as specified and as directed by Engineer- in- Charge. |
| 29 | S&F Mild Steel Butt Hinges 100mm, Medium Weight, Cold Rolled ISI Marked and fixed, complete all as specified and as directed. |
| 30 | S&F for 150mm long anodised aluminum barrel tower bolt of extruded aluminium section fixed with flat head ss screw complete all as specified and as directed by Engineer- in- Charge. |
| 31 | S&F aluminum alloy sliding door bolt 300mm long with hasp, staple (bolt type) adnd fixing clips of sheets, cast of exctruded sections and fiing bolts or extruded section complete all as specified and as directed by Engineer- in- Charge. |
| 32 | S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium/wooden/steel beads complete. |
| 33 | S&F 5.00 mm thick Sheet glass, plain pane ordinary quality fixing to Aluminium/wooden Sections as in Panel of Doors/Partitions and similar works with necessary fixing arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc and glazing with oil putty in sqm exc 0.5 sqm in each pane complete all as directed by Engr-in-Charge. |
| 34 | S&F 4.0mm thick sheet glass plain pane ordinary quality fixing to Doors/Windows/ Ventilator etc Works with necessary fixing arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc. or fixed with Oil Putty, as required at Site(s), area n exc 0.50 Sqm each pane complete all as specified and directed. |
| 35 | S&F 4.0mm thick Figured glass, pin head type, fixing to Aluminium/Steel Sections as in Panel of Windows/Ventillation with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc. or fixed with Oil Putty, as required/ordered at Site(s), area n exc 0.50 sqm each pane complete all as specified and directed. |
| 36 | Providing and fixing 12 mm thick prelaminated particle board flat with decorative lamination on one side and balancing lamination on other side pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 37 | S & F floor door stopper of size 75 mm long aluminium alloy body and tongue, anodized with hard drawn steel spring incl cleats etc fixed to door complete all as specified and as directed by Engineer- in- Charge. |
| 38 | Supply and fixing 100mm long stainless steel butt hinges heavy duty including steel screws for fixing complete all as specified and as directed by Engineer-in-charge. |
| 39 | S&F stainless steel sliding door bolt 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed and complete. |
| 40 | S&F stainless steel barrel tower bolts of extruded section 200 mm long complete. |
| 41 | S&F stainless steel barrel tower bolts of extruded section 150 mm long complete. |
| 42 | S&F stainless steel handles cast type anodised, 125 mm size complete. |
| 43 | S&F 300 mm, ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete. |
| 44 | M&L preparation of new or previously untreated surfaces of wood of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & incl one coat of pink primer complete all as specified. |
| 45 | M&L preparation of new or previously steel surfaces of any description not otherwise described width or girth and applying two coats of synthetic enamel paint over & incl one coat of red oxide primer complete all as specified. |
| 46 | S&F in repair 18/19 mm thick prelaminated particle board interior gde prelaminated one side with with decorative choice and other side white lamination fixed with screws as in cup board shutters & shelves and pelmet boxes etc complete all as specified and as directed by Engineer- in- Charge. |
| 47 | S&F in repair 25 mm thick Block board interior Gde 2 quality commercial type decorated face veneer on one face fixed with screws as in cup board shelves etc complete all as specified and as directed by Engineer- in- Charge. |
| 48 | S&F 2nd class hard wood plain fillets not exc 3 sqcm sectional area, square, rectangular or tringular in section, wrought fixed with nails complete all as specified and as directed by Engineer- in- Charge. |
| 49 | S&F in repair 18/19 mm thick WPC (Wood Plastic Composite) board, exterior grade, termite & borer proof, water resistant, factory finished, fixed with stainless steel screws as in cupboard shutters, shelves, pelmet boxes and kitchen cupboard works , with beading suitable for edge of shutter/cupboards etc., including all necessary fittings, including taking down old board of any type and any thickness.complete all as specified and directed by Engineer-in-Charge. |
| 50 | M & L in repair 18/19mm thick one side decorative and other side balancing lamination factory pressed HDHMR board with Borer resistant, fungal resistant, water resistant and termite resistant as per IS 710 of approved brand cup board shutter including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with two no of stainless steel L Bihari hinge and one SS handle 75 mm long handle on each shuutter etc. complete as per direction of Engineer-in- harge. (Payment of providing and fixing L bihari stainless steel hinges shall be paid separately) HDHMR. |
| 51 | M&L in repair 18/19mm thick both side balancing lamination factory pressed HDHMR board with Borer resistant, fungal resistant, water resistant and termite resistant as per IS 710 of approved brand boxes,shelves,racks, almirah, cupboard, handles and drawer etc. including necessary nails, screws etc. complete as per direction of Engineer-in charge. HDHMR. |
| 52 | S&F stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge. Note:- (i) One set comprises of two telescopic channel.(ii) Runner/ Channel should be SS 304 grade and load capacity should not be less than 45 kgs |
| 53 | S&F ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in charge. NOTE:- (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately) |
| 54 | S&F stainless steel L bihari Hinge with 0-15 degree crank and thickness upto 7 mm as required etc. complete and specified by Eng-in-charge. |
| 55 | S&F in repair, 40mm Magnet catcher fixing in cup board as approved by engr-in-Charge |
| 56 | S&F 50 mm Stain less steel hinges suitable for cupboard complete all as specified and as directed by Engr-in-Charge |
| 57 | S&F Contineous (piano) hinges, mild steel powder coated of 40 mm width of flaps(when open) complete all as specified. |
| 58 | S&F 100 mm long,designer pattern Stanless Steel handles for fixing in cupboards complete all as specified and directed by Engineer-in-Charge. |
| 59 | S&F in repair Mild Steel Butt Hinges 100mm, Medium Weight, Cold Rolled ISI Marked and fixed, complete all as specified and as directed. |
| 60 | S&F in repairs, 50 mm Stain less steel hinges suitable for cupboard complete all as specified and as directed by Engr-in-Charge |
| 61 | S&F in repairs contineous (piano) hinges, mild steel powder coated of 40 mm width of flaps(when open) complete all as specified. |
| 62 | S & F in repair floor door stopper of size 75 mm long aluminium alloy body and tongue, anodized with hard drawn steel spring incl cleats etc fixed to door complete all as specified and as directed by Engineer- in- Charge. |
| 63 | S&F in repair 75 mm butt hinges made up of extruded anodised aluminumfixed with flat head SS screw complete all as specified and as directed by Engineer- in- Charge. |
| 64 | S&F in repair Stain less Steel telescopic Kitchen Trolley channel 20\\" long complete all as specified and directed by Engr in charge. Make :- Hettich/Genric/Godrej/KYC/Spider etc |
| 65 | S&F aluminum door seal fixed to bottom of door shutters complete all as specified and as directed by Engineer- in- Charge. |
| 66 | S&F in repair for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium/woodem/steel beads complete. |
| 67 | Taking down old Aluminum door/windows of any description size exc.1.5 sqm but not exc. 4.00 sqm and M&L for complete over hauling of the glass pane frame/rubber beading/aluminum glazing clip sliding system locking system incl. necessary oiling and adjustment etc and refixing in same location complete all as directed. Note :- Glass Pane/rubber beeding/aluminum beading will be measured and paid separately under subsequent items. |
| 68 | -ditto- all as per srl item No. 66 above but area of door/windows/ventillation not exc 1.50 Sqm. |
| 69 | S & F in repair rubber beading to be fixed over glass panes in Aluminum windows complete all as directed. |
| 70 | S&F in repair, aluminum anodised glazing clip to the alumiinum window frames after fixing the glass panes complete all as specified and as directed by Engineer- in- Charge. |
| 71 | Hacking out old broken glass (any th size, quality or description) from wooden or steel frames glazed with putty or fixed with wooden beads complete all as specified and as directed by Engineer- in- Charge. |
| 72 | S&F in repairs, MS Helical door spring 300 mm long complete all as specified and as directed by Engr in Charge (Note:- Helical spring will be fixed by welding if required in MS frame) |
| 73 | S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body governing pivot made of brass,other parts made of mild steel heavy duty and fixed Complete all as specified and directed. |
| 74 | S&F in repair aluminium door closer hydraulically regulated, designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed Complete all as specified and directed. |
| 75 | S&F in repairs 25mm dia 16 gauge Aluminium powder coated curtain rods including cutting and fixing complete all as specified and as directed by Engr-in-Charge with stainless steel cover, |
| 76 | S& F designer pattern wall bracket suitable for 25mm dia curtain rods complete all as specified and as directed by Engr in Charge |
| 77 | S & F in repairs stainless steel rod 20 mm dia incl side caps and single/double brackets as in repairs complete all as specified and as directed. |
| 78 | S& F designer pattern side knobs/Domes suitable for 25mm dia curtain rods complete all as specified and as directed by Engr in Charge |
| 79 | S & F in repairs stainless steel rod 20 mm dia incl side caps and single/double brackets as in repairs complete all as specified and as directed. |
| 80 | M&L in repair for suspended false ceiling consisting of suitable GI sections of ‘T’ Angle & FI as per standard engineering practices with ‘E’ board classic ceiling boards 4mm thick in grid of 0.60x0.60mtr including cutting holes and making good holes for main joints, suspending with 4mm dia GI wire to roof slab, roof trusses, purlins & rafters etc and all as per approved and directed |
| 81 | S&F in repair Factory made single extruded PVC panels (Louvers) of Size 150x10mm /200x10mm/300x8mm to 10 mm as in wall cladding inclusive of solvent cement & fixing at site including with PVC frames as per manufacturer's instructions complete all as specified and as directed by Engineer- in- Charge. |
| 82 | S&F in repair Factory made single extruded WPC (Wood Polymer Composite) panels (Louvers) of Size 200x10mm/300x8mm to 10 mm as in wall cladding inclusive of solvent cement & fixing at site including with PVC/wpc frames as per manufacturer's instructions complete all as specified and as directed by Engineer- in- Charge. |
| 83 | S&F in repair, 6mm thick Glass shelf (22x6\\") with Brass CP Bracket with brass nut, complete all as specified and directed by Engr in charge. |
| 84 | S&F in repair, 6mm thick glass corner shelf (12\\"x12\\") with C type Brass CP bracket, complete all as specified and directed by Engr in charge. |
| 85 | Taking down Cement Plaster from wall and ceiling in patches of any description including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s) complete all as specified and as directed by Engineer- in- Charge. (Note :- Rate included for four storey building including scaffolding and all safety measures) |
| 86 | M&L for 15mm thick rendering in patches in CM 1:4 on fair faces of brick or concrete surfaces including finishing even and smooth without using extra cement all as specified and as directed by Engineer in Charge. |
| 87 | Dismantling Plain or corrugated steel sheeting any guage, thickness, including removing from site complete all as specified and as directed by Engineer- in- Charge. |
| 88 | Dismantling wrought iron or mild steel work of any description not otherwise provided for including removing from site complete all as specified and as directed by Engineer- in- Charge. |
| 89 | Excavating in post holes each n.exc 0.50 cum getting out hard dence soil including returning filling in and ramming earth or broken rubble mixed with earth around ,in layers n.exc 25 cm ,watering and removing surplus soil to a distance n.exc 50 mtr and making good surface. |
| 90 | M&L cement concrete in foundations filling, mass concrete PCC 1:3:6 using 40 mm graded stone aggregate type C2 |
| 91 | S&F mild steel works in Joist, channel, angle or tee sections, posts, rafters, purlins, trusses, connecting plates, etc. fixed independently conforming to Fe-410-W(Gde E-250) Quality-A |
| 92 | S & F MS Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.Fe 410 -W (Gde- E- 250)quality- A fe complete all as specified and as directed. |
| 93 | S & F of MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk)forming holes, with riveted, bolted or welded attachment complete all as specified and directed |
| 94 | S&F MS screw bolts (machine made) with hexagonal or square heads at one ends and screwed the other, or screwed both ends, each screwed end to be fitting with washer and one hexagonal or square nut but length of boltexc 5cm but n exc 10cm long and dia of shank 11 to 15 mm etc. |
| 95 | Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified. |
| 96 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as wall, fixed with self in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge. |
| 97 | Taking down steel rolling shutter of size exc 3.00 Sqm and n exc 15 sqm and refixing the same after greasing of MS spring and side guide making and functional after overhaling. (Note : Supply of material to be measured seperately) |
| 98 | Supply only of MS pipe medium grade of dia upto 40 mm including cutting and fixing, drilling, welding for rolling shutter all as directed |
| 99 | Supply only spring of high carbon spring 30mm dia drilling, welding for rolling shutter all as directed |
| 100 | Supply Ball bearing for rolling shutters |
| 101 | S & F in repair mild steel rolling shutter strips made out of 1.25mm MS sheet including and reavting including one coat of primer and two coat of synthetic enmail paint all as directed Engr-in-Charge. |
| 102 | S&F in repair 0.63mm Mild steel, plain, black sheet in wall cladding,steel gates, rolling shutter hood and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required. |
| 103 | S&F in repair Safety lever locks mild steel with 4 levers for rolling shutters |
| 104 | S&F in repair Mild Steel 1.25 mm rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated,complete: push pull or manual type. |
| 105 | -Ditto-, item No - 72 above, but gear operated type with bevel gear box and crank handle. |
| 106 | M&L for 20 mm thick granite (any type) slab for window cills/ Kitchen platefor and etc laid with 15 mm thick CM 1:4 as in bedded in floor/wall and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing all as specified and directed by Engr-in-charge |
| 107 | M&L for preparing new plastered surfaces plastered on walls including cornices plasters and applying two coat of oil bound distemper in patches over a coat of primer complete and over 1 to 2 mm thick birla putty punning complete all as specified. |
| 108 | S&F of Oil-resistant, Re-positionalble and Eco-friendly strain resistance colour wall paper including fixing with adhesive and cutting to required shape complete in all respect to the satisfaction of Engr-in-charge and also adhere to below specifications:-(a) All wall paper to be erected from floor to the bottom of the ceiling or as specified.(b) All opening for the cutout for ducting/ raceways/ cables etc, in the partition to be closed and made air tight.(c) Disposing waste material from the site. |
| 109 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. |
| 110 | S&F in repair 12mm thick Toughned glass with or without logo as required in doors/ partitions /automatic doors and similar work including cutting to shape, drilling holes required, with 02 Nos fancy handle of size 300 mm long, locking arrangement, floor springs/ frame supports etc complete all as specified and directed by Engr-in-Charge (Note:- Rate of etched logo is inclusive of rate quoted by the contractor). |
| 111 | S&F repair Semi perforated 12 mm thick micro tegular edged false ceiling at all heights with GRG false with GRG (Glass Fibre With Semi With fully Reinforced Gypsum) false ceiling tiles of perforated 12mm Size 595 x 595 mm of approved texture, 12mm thick micro tegular design and patterns having moisture micro tegular edged or 1 0 mm content less than 2%, humidity resistance edged GRG thick square edged of 99%, NRC0.50 to 0.75 as per IS false ceiling GRG false ceiling 8225:1987, Noncombustible as per BS tiles tiles 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawingand as per directions of the Engineer-in-Charge. |
| 112 | Dismantling floor, stone, hearth or wall tiling including cement mortar bedding but not backing, removing rubbish off the premises complete all as specified and directed by Engr-in-charge. |
| 113 | Demolition of Cement Concrete (un-reinforced) of any description, not exc. 150mm thickness (above or below Ground Level) and removing the same from Site(s), complete all as specified and as directed. |
| 114 | M&L for 25mm thick PCC 1:2:4 Type B0 (12.5mm Graded Stone Aggregate) as in sub floor etc., including rough top surface to receive floor finish complete all as specified and as directed. |
| 115 | M&L for 40 mm thick PCC 1:2:4 Type B0 (12.5mm Graded Stone Aggregate) as in sub floor etc., including rough top surface to receive floor finish complete all as specified and as directed. |
| 116 | M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or colouredcement to match over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete including all as specified and directed by Engr-in-charge. |
| 117 | M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square/ rectangular ) in floors/ skirting ,area of each tile exc 0.11 sqm but n.exc. 0.18 sqm set and jointed in neat cement slurry and pointed in white or colour cement to match, over and including 20 mm thick screed plaster in CM 1:4 complete all as specified and directed by Engr-in-charge. |
| 118 | M & L Coloured Non Skid ceramic tiles 7 to 8 mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:4) complete all as specified and directed |
| 119 | M&L for glazed ceramic colour tiles of of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm set and jointed in neat cement slurry and pointed in coloured cement on vertical surfaces such as in dado/skirting etc over and including 10 mm thick backing coat in CM 1:4, complete all as specified and directed by Engr-in-charge. |
| 120 | M&L for 10 mm thick Vitrified light shade Coloured tiles, square/ rectangular double polished, area of each tile n.exc. 0.36 sqm, in floor including 15 mm thick screed bed in CM 1:6 etc.,set and jointed in neat cement slurry and pointed in white with pigment to match for laying floor finishes all as specified and as directed by Engr-in-Charge. |
| 121 | M&L for 10 mm thick vitrified light shade coloured tiles (square/ rectangular) double polished, area of each tile not exc 0.36 sqm set and jointed in neat cement slurry and pointed in coloured cement on vertical surface such as Skirting/ dado etc over and including 10mm thick backing coat in CM 1:4, complete all as specified and as directed by Engr-in-charge. Please Enable Macros to View BoQ information |
| 122 | M&L for 10 mm thick vitrified light shade coloured tiles (square/ rectangular) double polished, area of each tile not exc 0.36 sqm set and jointed in neat cement slurry and pointed in coloured cement on vertical surface such as Skirting/ dado etc over and including 10mm thick backing coat in CM 1:4, complete all as specified and as directed by Engr-in-charge. Please Enable Macros to View BoQ information |
