|
| 1 | M&L for preparing black top surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with air compressor through air jet to remove all loose dirt etc and applying evenly a priming/tack coat of paving bitumen primer of grade VG-10 at the rate of 5 Kg per 10 Sqm of surface by sprayer operated on hot pressure mechanism complete all as specified and as directed. |
| 2 | M&L for repairs to pot holes, not exc 1 square metre each, including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, cutting around edges to at least 25 mm in depth, on existing road surfaces, and making good applying evenly a tack coat of paving bitumen primer of grade VG-10 at the rate of 05 Kg per 10 Sqm, putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 Kg per 10 sqm of paving bitumen (VG-30), blinded with 0.09 Cum of stone chippings, 6.3 mm size and again well rammed including supply of premixed macadam, binder and chipping, depth of pot holes exc 30mm, complete all as specified and as directed.Note : Job mix formula of premix bituminous macadam shall be approved by GE. |
| 3 | M&L for repair to potholes any depth, not exc 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal of granite, trap or basalt stone), complete all as specified and as directed. |
| 4 | M&L for providing, laying, spreading premix bituminous macadam with crushed and graded stone aggregate mixed together with 4% of paving bitumen of grade VG-30 by weight of total mix including heating bitumen to the required temperature, mixing bituminous macadam in automatic and temperature controlled hot mixing plant, laying, spreading by means of mechanical paver and rolling and consolidating to the required gradient and camber (consolidated thickness 75 mm or less) with 8 to 12 tonne power road roller complete all as specified and as directed.Notes : (i) Job mix formula of premix bituminous macadam shall be approved by GE. |
| 5 | M&L for providing, laying, spreading 30mm thick (consolidated thickness) of premix Semi Dense Asphaltic Concrete (SDAC) with crushed and graded coarse aggregates as per design based on Job mix formula with 5.5% bitumen binder content (bitumen of Grade VG-30) by weight of total mix including heating bitumen to the required temperature, mixing bituminous concrete in automatic and temperature controlled hot mixing plant, laying, spreading uniformly by means of Mechanical paver and rolling and consolidating to the required gradient and camber with 8 to 12 tonne power road roller and Vibromax roller to a uniform smooth surfaces complete all as specified and as directed.Notes : (i) The work shall be executed as per design mix approved by GE. (ii) Paving bitumen of Grade VG-30 for semi dense asphaltic concrete shall be used and shall be procured by the contractor under his own arrangement and at his own cost. (iii) Cost of all the materials, T&P, labour etc. required for preparation of surfaces, providing and laying semi dense asphaltic concrete including procurement of bitumen as specified here-in-before, stone aggregates & sand etc., rolling and all other elements required for entire completion of the job shall be deemed to be included in the unit rate quoted for this item. (iv) Bituminous concrete shall be mixed in drum type hot mix plant, transported from plant to work at site and laid/spread by means of mechanical paver finisher. (v) Filler for bitumen concrete shall be OPC grade @ 2% of total mix. (vi) Contractor shall quote his rate on the basis of binder as mentioned in this item. If there is any minus variation in the actual binder content used as per design mix approved by GE, the rate shall be adjusted as per invoice submitted by the contractor per Kg of binder used. However no price adjustment shall be made if the binder content works out to more than as specified in this item. |
| 6 | M&L for painting lines, dashes, arrows letters, marking 3mm thick painting new or previously treated road surfaces with hot applied retro reflective thermoplastic n exc 10cm wide road marking paint (white/golden/yellow) conforming to Morth (Clause 803.4) all as specified with 8% glass beads using special applicator machine with heating arrangement upto 160 degree C including cleaning and drying the existing road surfaces to ensure dust, oil, grease and moisture free surface before applying the paint complete all as specified and as directed. |
| 7 | Material and labour for providing and applying 2.5 mm thick road marking strips (Retro-reflective) for centre line, stop lines , dashes and the like exc 10 cm wide on road specified shade/colour using hot thermoplastic material by fully automatic thermoplastic paint applicator machine fitted with profile shoe, Glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cleaning the road surface of all dirt, seals, oil, grease and foreign material etc, complete all as specified and directed and accordance with manufactuers specifications. |
| 8 | Demolition of cement concrete (unreinforced) in ground floor and pavings exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified & as directed. |
| 9 | M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified & as directed. |
| 10 | M&L for preparation of newly untreated plastered surfaces of any description over 10cm in width or girth and applying tow coats of synthetic emulsion paint of approved shade/tint complete all as specified & as directed. |
| 11 | M&L for 75mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base in floor, surface finished fair and even complete all as specified and directed. |
| 12 | M&L for factory made 80mm thick machine pressed precast cement concrete polished (reflecting type) interlocking paver blocks of Grade M-40 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment with coloured top casted in an automatic plant working on vibration and simultaneous hydraulic compression from top, laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & as directed. Note : Shape & colour of paver blocks shall be as approved by the GE. |
| 13 | M&L for factory made 80mm thick machine pressed precast cement concrete coloured designer polished (reflecting type) interlocking paver blocks of Grade M-40 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment with coloured top casted in an automatic plant working on vibration and simultaneous hydraulic compression from top, laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & as directed. Note : Shape & colour of paver blocks shall be as approved by the GE. |
| 14 | Supply and fixing dual directional reflective cat eye reflective type of plastic body of size 100mm x 100mm x 19mm with impact resistant ABS plastic stud having ultra voilet resistant colour with plastic strip containing 31 mini retro reflector in PMMA glass beads of colour white/red/yellow to each side and fixed with including 12mm dia 120mm long zinc plated steel nails at the centre of cats eye by hammering as per manufacturer’s instructions complete all as specified and as directed including dismantling and taking out old unserviceable / broken road stud / cat eye of any type. |
| 15 | S&F Solar delineator made out of polycarbonate four ultra bright flashing LEDs which give 360 degrees viewing, available in red and yellow colours, special base for mounting on cone, pole etc high quality reflactive solar panel to maximize sun absorption and operating time 3-4 consecutive days (with full battery charge), high intensity retro reflective band of 1\\" width for extra visibility and mounted on 50mm dia mild steel pipe of 1010mm height duly powder coated with anti theft steel net for reflactor protection including delineator shall be fixed in plain cement concrete 1:2:4 Type B1 (using 20mm graded stone aggregate) block of size 300x300x300mm deep, including necessary excavation & earthwork, complete all as specified and as directed including dismantling and taking out old unserviceable / broken delineator of any type. |
| 16 | Supply & fixing road stud of size 100 x 100 x 18.5 mm, two way reflective, ABS body, Red or Amber colour, complete all as specified and as directed including dismantling and taking out old unserviceable / broken road stud of any type. |
| 17 | S&F Solar Stud of size 125mm x 125mm x 25mm (shank 65 mm), aluminium alloy shell, electronically operated automatically turns ON at night and turns OFF at day, high efficiency mono crystalline solar panel 2.4 V / 0.3 Watt, one Ni-Mh or Ni-Cd rechargeable battery (1.2 V / 1600 MA), six super bright LEDs with 10000 to 18000 mcd (Millicandela), view distance upto 1000m, flash rate 2 Hz, capable to withstand weight upto 10 tonne, unbreakable poly carbonate clear facing designed for maintenance free operation, 100% water proof design according to IP-65, Red or Amber colour, including dismantling and taking out old unserviceable / broken solar stud of any type complete all as specified and as directed. |
| 18 | Supply and fixing of 240mm x 730mm x 70mm safety plastic Bumps highest quality High Density Polyethylene (HDPE/PE) UV stabilized so does not fade in sunlight that it can bear maximum load on it. Highly resistent to severe impacts and harsh weather conditions. The body of the speed bump made of PE plastic material. Two highly reflective reflectors moulded in PMMA material welded with ABS base plate through ultrasonic welding process and then fixed on the speed bump so that dust and water cannot touch the reflector’s inside area and thus it maintains its reflectivity for a long time. 6 Nos metallic bolts are used for installation on road. Available in Yellow & Black colour including dismantling of old unserviceable / broken sefety bumps of any type & size complete all as specified & as directed. |
| 19 | M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in roof kerbs, copings, side filling and rounded chamfered edges and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed. Please Enable Macros to View BoQ information |
