|
| 1 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) etc. and clearing off the premises complete all as specified and directed by Engineer-in-Charge. |
| 2 | Material and labour for screed bed or bedding layer of cement mortar 15 mm thick in CM 1:6 for laying floor finishescomplete all as specified and directed by Engineer-in-Charge. |
| 3 | Material and labour for Non Skid coloured joint free ceramic tiles 7mm to 8mm thick of area exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 4 | Material and labour for Non Skid coloured ceramic tiles joint free, 7mm to 8mm thick of area exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 5 | Material and labour for plastering 10mm thick in cement mortar 1:4 finished rough (as in vertical surfaces like dado & skirting) complete all as specified and directed. |
| 6 | Material and labour for coloured pattern glazed ceramic tiles 6 to 7mm thick of size 300mm x 450mm as in skirting, dados etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 7 | Material and labour for vitrified ceramic tiles 9 to 10 mm thick (square /rectangular) polished, area of each tiles not exceeding 0.36 sqm as in flooring set and joined in neat cement slurry and pointed in coloured cement to match coloured tiles complete all as specified and directed. |
| 8 | Demolition of cement concrete in below or above ground level n exc 150mm thick complete all as specified and directed. |
| 9 | Material and labour for applying acrylic cementicious polymer modified elastomeric waterproofing & protective coating like brush bond of Fosroc or Pidifin 2K (Pidilite) as per manufacturer instructions on rendered surfaces of floor and wall of sunken portion comples all as specified and directed. |
| 10 | Material and labour for cement concrete 75mm thick type C-2, 1:3:6 (40mm graded aggregate) as in plinth protection, paving etc complete all as specified and directed |
| 11 | Material and labour for PCC 1:5:10, Type E-2 using 40mm graded aggregate as in mass concrete (sunken portion) complete all as specified and directed. |
| 12 | Material and labour for PCC 1:2:4, 25mm thick, type B-1 using 20mm graded aggregate as in sub base complete all as specified and directed. |
| 13 | Dismantling of stone slab and tiles of any size and description or thickness in floors, dados & aprons etc. laid bedded and pointed in any mortar complete all as specified and directed. |
| 14 | Material and labour for 20mm thick granite (of any type) work (Table rubbed and polished) in steps, jambs, pillars, windows cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including screed bed of 15mm in cement mortar 1:6 complete all as specified and directed. |
| 15 | Material and Labour for machine cut cudappah stone slab 20 to 25mm thick laid over and including screed bed of 15mm thick in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 16 | Rounding to edges of stone slabs one edge, such as in steps, platform, and other similar situations complete all as specified and directed. |
| 17 | Drilling holes on granite, cudappa or trap stone for bolts, pipes etc. n exc 25mm dia complete all as specified and directed |
| 18 | Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 19 | Material and labour for plastering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 (internal) complete all as specified and directed. |
| 20 | Material and labour for preparation of newly plastered wall surface and applying two coats of oil bound distemper over a coat of interior primer including 1mm thick wall care putty complete all as specified and directed. |
| 21 | Material and labour for 5mm thick cement plaster on cement concrete surfaces as in ceiling in cement mortar 1:3 complete all as specified and directed. |
| 22 | Material and labour for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed. |
| 23 | Taking down shutters only of any description exc 1sqm but n exc 2sqm each and removing from site complete all as specified and directed. |
| 24 | Taking down chowkats or frames not exceeding 1.50 sqm each with shutters (without taking off shutters from the frame) and removing from site complete all as specified and directed. |
| 25 | Taking down chowkats or frames exceeding 1.50sqm but not exceeding 4.00 sqm each with shutters (without taking off shutters from the frame) and removing from site complete all as specified and directed. |
| 26 | Taking down door shutter exc 1 Sqm and n exc 2 sqm each for resecuring or easing & adjusting and refixing in same position complete all as specified and directed. |
| 27 | Supply and fix 125mm x 60mm size of pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and as directed. |
| 28 | Supply and fix 105mm x 60mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all specified and as directed. |
| 29 | Material and labour for plain cement concrete Type C-1, 1:3:6 (using 20mm graded crushed stone aggregate) for filling of hollow pressed steel frame complete all as specified and directed. |
| 30 | Supply and fix 30 mm thick factory made shutters of 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass or gauge etc, with sash bars, edges of sash bars framing, moulded, fitted with cut and mitred beads for securing glass or gauge etc sizes of members of shutters as specified in SSR part -I, section 8 caluse 8.20 (a) complete all as specified and directed. |
| 31 | Supply and fix 30 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on boths sides complete all as specified and directed. |
| 32 | Supply and fix factory made PVC solid door frame or chowkat of size 50mmx47mm, made out of 5mm plain colour PVC sheet reinforced with mild steel square tube etc. including necessary hold fasts, complete all as specified and directed. |
| 33 | Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with and including heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with and including solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with and including solvent cement and fixed in the frame complete all as specified and directed. |
| 34 | Supply and fix 100mm Butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and directed. |
| 35 | Supply and fix 150mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 36 | Supply and fix 150mm extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed. |
| 37 | Supply and Fix 300mm aluminium alloy sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed compete all as specified and directed. |
| 38 | Material and labour for 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work including 6mm thick lipping pati complete all as specified and directed. |
| 39 | Material and labour for 12 mm width teak wood lippind of 6mm thick fixed with nails over particle board complete all as specified and directed. |
| 40 | Supply and fix Steel rolling shutters, Thickness of laths in 1.00 mm with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, push pull or manual type complete all as specified and directed. |
| 41 | Material and labour for preparing new wood and wood based surfaces and applying two coats of synthetic enamel paint over a coat of pink primer over 10cm width/girth complete all as specified and directed. |
| 42 | Supply and fix stainless steel wire cloth 0.254mm (30Gauge) nominal dia of wire and average width of aperture 0.95mm and fixed with stainless steel wire staples/nut boults, etc with including necessary wooden beads complete all as specified and directed by Engr-in-charge. |
| 43 | Supply and fix in repairs aluminium door stopper of size 60 to 75mm long double legged fixed to bottom rail of door shutter provided with rubber bushing at one end the door at floor and other end provided with aluminium plate fixed with door shutter with screws at appropriate height complete all as specified and directed. |
| 44 | Welding in repairs n. exc 2.5cm in length and thickness of metal to be welded n. exc. 6mm for windows/doors shutters/Hinges etc. incl cleaninig and preparing the surfaces complete all as specified and directed. |
| 45 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be Powder coated (minimum thickness of powder coating 50 micron) smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 46 | Providing and fixing aluminium Powder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete all as specified and directed by Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately). |
| 47 | Supply and fix sheet glass 4mm thick ordinary quality, in squares n. exc 0.5 sqm each pane and fixed to wooden / aluminium shutter complete all as specified and directed. |
| 48 | Supply and fix stainless steel wire cloth 0.254mm (30gauge) nominal dia of wire and average width of aperture 0.95mm and fixed with stainless steel wire staples/nut boults etc. with including necessary wooden / aluminium beads complete all as specified and directed by Egnr-in-charge. |
| 49 | Supply and Fix aluminium louvered ventilators of section size 100mmx25mmx1.50mm including frosted glass fixed in half portion & adjutable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc. including taking down existing steel ventilator complete all as specified and as directed by Engr - in - Charge. |
| 50 | Supply and Fix 3mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5sqm in each pane including hacking out old broken glass any thickness, size from wooden/metal frame, glazed with putty or fixed with beads complete all a specified and directed. |
| 51 | Supply and Fix in repairs 20mm dia curtain rod mild steel chromium plated as per windows and door size including finials (brackets on end) with brackets duly screwed on wall with plastic roll plug and stainless steel screw of 38mm long complete all a specified and directed. |
| 52 | Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed. |
| 53 | Providing and fixing 15 mm nominal bore Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 Metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed by Engineer in Charge. |
| 54 | Material and labour for cutting chases, pinning in, making good to facings of brick wall where required and pointing in cement mortar 1:3 ends of landings, steps, cills, sunshades, shelves, lintels etc. and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, cutting not exc 10cm girth complete all as specified and directed. |
| 55 | Supply and fix in repairs brass chromium plated health faucet not less than 1 metre long complete for EWC complete all as specified and directed. |
| 56 | Supply and fix in repairs two way bib cock fancy type, chromium plated complete all as specified directed. |
| 57 | Supply and fix in repairs 15mm bore bib taps fancy type, cast copper alloy, chromium plated, with cruth or butterfly handle, screwed down for iron pipe complete all as specified and directed. |
| 58 | Supply and fix in repairs, vitreous china wash basin, ivory, flat back, size 450mm x 300mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe including 15mm bore pillar taps, fancy type, cast copper alloy with capstain heads, chromium plated complete all as spcified and directed. |
| 59 | Supply and fix 15mm bore pillar taps, fancy type, cast copper alloy, with capstain heads, chromium plated, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified & directed. |
| 60 | Supply and fix in repairs shower rose 195mm long CP suitable for 15mm bore pipe complete all as specified and directed. |
| 61 | Supply and fix in repairs 15mm bore angular stop cock fancy type, chromium plated cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed |
| 62 | Supply and fix in repairs 15mm bore angular stop valves, cast copper alloy, fancy type, chromium plated with long or short shank and cup (concealed type) screwed down high pressure, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 63 | Supply and fix in repairs 15mm Brass CP wall mixer tap including provision for overhead shower for mixing \\"Hot or Cold\\" water screwed down for iron pipe complete all as specified and directed |
| 64 | Supply and Fix in repairs PVC connection pipe 15mm dia and 450mm long complete all as specified and directed. |
| 65 | Supply and Fix in repairs PVC waste pipe 32mm dia for WHB/Sink (Make as per sample) complete all as specified and directed. |
| 66 | Supply and fix in repair CP grating 100mm size fixing with white / grey cement (suitable for toilet, bathroom, WHB and kitchen sink) complete all as spcified and directed. |
| 67 | Supply and fix in repairs 75mm dia PVC (SWR) Floor trap plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete type B1 1:2:4 using 20mm graded stone aggregate complete all as specified and directed by Engineer-in-charge.. |
| 68 | Supply and Fix 600mm x 450mm x 5mm thick mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood backing and 12.7mm x 1.25mm thick aluminium angle frame fixed to wall with rawal plugs and screws on wall complete all as specified and directed. |
| 69 | Supply and fix in repairs stainless steel tubular towel rail 20mm dia, D type, 60cm long 1.60mm thick complete all as specified and directed. |
| 70 | Supply and fix in repairs, sinks made of stainless steel 1mm thick with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 71 | Supply and fix in repairs vitreous china wash down water closet pan size 580mm (pedestal pattern) ivory coloured with integrated 'P' or 'S' trap outlelt including connection to flush pipe and out going pipe and plastic water closet seat cover ivory coloured closed pattern with flat bottom and PTMT hinging device complete all as specified and directed. |
| 72 | Supply and fix in repairs vitreous china water closet squatting pan 'orissa pattern', ivory coloured of size 580mm x 440mm with integral foot rest and outlet for 'P' or 'S' trap, WC pan shall be set in lean concrete below level of rim of pan to receive the floor finish complete all as specified and directed. |
| 73 | Supply and fix in repairs PVC valveless syphonic action type flushing cistern 10 litres capacity low level, white with inlet ball valve, float and handle including brackets flush pipe of polythene of low or high density of PVC 32mm dia for low level cistern complete all as specified and directed. |
| 74 | Supply only PVC valveless syphonic action type flushing cistern 10 litres capacity low level, white with inlet ball valve, float and handle including brackets flush pipe of polythene of low or high density of PVC 32mm dia for low level cistern complete all as specified and directed. |
| 75 | Supply and fix in repairs 40mm bore low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. including necessary fittings complete all as specified and directed. |
| 76 | Demolition and breaking up drain PVC (SWR) pipes jointed in cement mortar / solvent internal dia of pipe upto 110mm in any position with wall or in floor etc complete all as specified and directed |
| 77 | Supply and fix 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls complete all as specified as directed. |
| 78 | Supply and fix 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls complete all as specified as directed. |
| 79 | Supply and fix 75mm PVC (SWR) bends any radius complete all as specified as directed. |
| 80 | Supply and fix 75mm PVC (SWR) bends any radius with acess door complete all as specified as directed. |
| 81 | Supply and fix 110mm PVC (SWR) bends any radius complete all as specified as directed. |
| 82 | Supply and fix 75mm PVC (SWR) branch piece single (single Y) equal or unequal with acess door complete all as specified as directed. |
| 83 | Supply and fix 110mm PVC (SWR) branch piece single (single Y) equal or unequal with acess door complete all as specified as directed. |
| 84 | Supply and fix in repair stainless steel plate rack of size 900mm x 600mmm made out of 1mm thick stainless steel sheet of grade 304 fixed all as per manufacturers instructions complete all as specified and directed by Engineer-in charge. |
| 85 | Dismantling plain or corrugated asbestos cement sheet etc in roof covering complete all as specified and directed. |
| 86 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 87 | Supply and Fix rolled mild steel surfaces for framed brackets, rafter, purlins, rails and similar work (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. confirming to Fe-290 (Gde E-165) including cutting, drilling, welding or connecting to bolts and nuts complete all as specified and as directed. |
| 88 | Supply and fix Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 89 | Supply and fix in repairs 20mm gun metal gate valves with iron valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 90 | Preparation of new steel and iron surfaces and applying two coats of Synthetic enamel paint over a coat of red oxide zinc crome primer over 10cm width/grith complete all as specified and directed |
| 91 | Dismantling of water tanks of exc 250 litres and n exc 500 litres capacity and removing to store and supply and fix 500 litres capacity rotational moulded polythelene water storage three layered tanks ISI marked (Cylindrical vertical with clsoed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed. |
| 92 | Dismantling of water tanks of exc 500 litres and n exc 1000 litres capacity and removing to store and supply and fix 1000 litres capacity rotational moulded polythelene water storage three layered tanks ISI marked (Cylindrical vertical with clsoed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed. Please Enable Macros to View BoQ information |
