|
| 1 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cementlime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing the debris outside from defence land complete all as specified and directed. |
| 2 | Demolition of cement concrete or lime concrete (unreinforced) in ground floors and Pavings not exc 15 cm thick (below or above ground level ) and removing the debris outside from defence land complete all as specified and directed. |
| 3 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 4 | M&L for broken stone or boulder hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 5 | M&L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and, mass concrete, sub base etc complete all as specified and directed. |
| 6 | M & L for brick work old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed. |
| 7 | M&L for 100mm thick PCC (1:2:4), type B-1 using 20mm graded stone aggregate as in flooring/paving finished even & smooth with using extra cement complete all as specified and directed. |
| 8 | M&L for 10mm thick renedering on fair faces of brick work or concrete surfaces in cement mortar (1:6) with using water proofing compound finished even and smooth without using extra cement complete all as specified and directed. Note:-WPC shall be measured and paid seperately. |
| 9 | M&L for 15mm thick rendering on fair faces of brick surfaces in CM (1:4) with using water proofing compound finished surfaces even and smooth without using extra cement complete all as specified and directed. Note:-WPC shall be measured and paid seperately. |
| 10 | Supply only Integral waterproofing compound complete all as specified and directed. |
| 11 | Providing and application of 10mm thick plaster in CM (1:4) cement : sand plaster admixed with and including integral water proofing compound Rheomac 707 @ 1000 ml per bag of cement over the dome area including bonding coat of Polyalk EP and cement slury to the plaster area or as per the direction including necessary steel scaffolding, steel plateform and proper supporting by steel prop etc complete all as specified and directed. |
| 12 | Providing & laying of 25mm thick Emaco S88 CT or equivalent fibre reinforced pre - packed Polymer Modified cementitious Mortar on the sound substrate and making the surface is original shape & Cure it for 3 days including necessary steel scaffolding, steel plateform and proper supporting by steel prop etc complete all as specified and directed. |
| 13 | Providing and applying of three coats of water proofing acrylic co polymer confirms to DIN 1048 by mixing of 1 kg WP polymer and 1.25 kg of cement for first coat, than laying second layer of Fibre glass mesh cloth when the first WP layer is still green. Overlap of joints of Fibre cloth should not be less than 10 cm, than finally apply 3rd layer Mix of WP polymer cement slurry by brush to entire surface of container. Cure it for 3 days including necessary steel scaffolding, steel plateform and proper supporting by steel prop etc complete all as specified and directed. |
| 14 | Providing and application of primer & two coats of non-algai, non fungai, anti carbonation and hygienic coating of SUNEXT - 8 MAKE OF Sunanda sp. Coating ltd to entire interior area of tank as per instruction of Engr-in charge, including necessary additional scaffolding / plateform , steel prop etc. to full height of tank complete all as specified and directed. |
| 15 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10 sqm over new or old surfaces complete all as specified and as directed. |
| 16 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed |
| 17 | S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-410- W(Gde E-250) quality 'B' complete all as specified and directed. |
| 18 | M&L for preparation of new steel surface of any desciption not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat red oxide primer complete all as specified and directed. |
| 19 | Taking up or down 40mm steel tubing and connections, including cleaning for refixing or removal from site complete all as specified and directed. |
| 20 | S&F 40mm bore GI tubing medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed |
| 21 | Excavating over areas, n exc 1.50 m deep and getting out in any type of soil complete all as specified and directed. |
| 22 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for laying of pipeline N exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil in location of hill area up to 16 km from motor vehicle road complete all as specified and directed. |
| 23 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for laying of pipeline. N exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/disintegrated rocks in location of hill area up to 16 km from motor vehicle road complete all as specified and directed. |
| 24 | Returning filling in incl spreading leveling, watering and well ramming in layers n exc 25 cm complete all as specified and directed. |
| 25 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 26 | M&L for walling of random rubble masonary, uncoused, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and directed. |
| 27 | M&L for PCC (1:2:4), type B-0 (using 12.5mm graded crushed stone aggregate) as in benching, bed plates, copings and the like including necessary formwork, complete all as specified and directed. |
| 28 | M&L for pre cast cement concrete (1:2:4), type B-1 (using 20mm graded crushed stone aggregate) set in cement mortar 1:6 in bond stones for stone masonry and the like including necessary formwork, complete all as specified and directed |
| 29 | M&L for RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate in foundation, including rafts, footings, beams, plinth beams; bases for columns; etc; basement slabs, under-remed piles and mass concrete complete all as specified and directed. |
| 30 | M&L for RCC (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in cloumns, pillars, piers, posts and struts complete all as specified and directed. |
| 31 | M&L for RCC nominal mix 1:2:4 (using 20 mm graded stone aggregate ) in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses cpmplete all as specified and directed. |
| 32 | M&L for RCC nominal mix 1:2:4 (using 20 mm graded stone aggregate ) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 33 | M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished concrete surfaces completed all as specified and directed |
| 34 | M&L for formwork to sides of pillars, piers, columns, square, rectangular, polygonal, circular on plan rough finished surfaces of concrete completed all as specified and directed |
| 35 | M&L for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter rough finished surfaces of concrete complete all as specified and directed. |
| 36 | M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete complete all as specified and directed. |
| 37 | S&F MS TMT bars10mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping forcolumns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia confirming to Fe 500 or Fe 550 complete all as specified and directed. |
| 38 | All as per item No 37 above but 5mm dia and over upto and including 10mm dia in stirrups spacers and binder. |
| 39 | M&L for 15mm thick rendering on stone masonry surfaces in CM (1:4) with using water proofing compound finished surfaces even and fair complete all as specified and directed. Note:WPC shall be measured and paid seperately. |
| 40 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars for drain cover, barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 41 | M&L for 200mm dia reinforced cement concrete pipe class NP-3 laid and joionted with collars complete all as specified and directed. |
| 42 | M&L for PCC 1:4:8 type D-2, 40mm graded agg as in concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 200 mm bore of drain pipe complete all as specified and directed. |
| 43 | M & L for PCC 1:2:4 type B-2 using 40 mm graded stone aggregate complete all as specified and directed. |
| 44 | M&L for preparation of new or previously untreated surfaces of steel of any description, not exc 10cm in width or girth when unconnected with other painting and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 45 | M&L for boulder filling dry hand packed tightly as in back of wall complete all as specified and directed. |
| 46 | S & F 110 mm bore of pipe PVC (SWR) pipes single socket in any length as in weep holes etc complete all as specified and directed |
| 47 | Taking up 150 mm bore cast iron / DI / GI pipes (including all fittings) with spigot and socket end and lead joints including burning out lead joints and recovering lead complete all as specified and as directed. (Note : Excavation and earth work shall be measured and paid seperately.) |
| 48 | All as per item No.47 above but size 100 mm bore of pipe. |
| 49 | Supply, laying and testing ductile iron (DI) pipe 150mm bore water mains with flanged ends, (both end flanged ) centrifugally cast of class K-7, included flanged rubber gasket nut bolts etc complete all as specified and directed. Note:DI spacials / fitting, excavation & earth work shall be measured and paid separately). |
| 50 | All as per item No.49 above but size 100 mm bore of pipe. |
| 51 | S & F 150mm bore, cast iron sluice valve both end flanged, class PN 1.6 conforming to IS -14846 (raising stem type) with iron wheel head and stainless steel spindle including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking up/down old sluice valve complete all as specified and as directed. |
| 52 | All as per item No.51 above but size 100 mm bore of valve. |
| 53 | All as per item No.51 above but size 80 mm bore of valve. |
| 54 | S & F 150mm bore, cast iron butter fly valve both end flanged, class PN 1.6 conforming to relevant IS lever operated including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking out existing one complete all as specified and as directed. o |
| 55 | All as per item No.54 above but size 100 mm bore. |
| 56 | All as per item No.54 abov but size 80 mm bore. |
| 57 | S & F 80 mm bore, Cast iron Non-return (reflux) valve, flange type with by-pass arrangement suitable for 80 mm dia water mains conforming to IS-5312 Part-I class PN 1.6 including takind down existing one complete all as specified and as directed. |
| 58 | All as per item No.57 above but size 100 mm bore. |
| 59 | All as per item No.57 above but size 150 mm bore. |
| 60 | Taking up or down 150 mm bore CI/DI/galvanised steel tubing including connections from trenches/wall/floor/ceiling etc and keeping serviceable pipes in safe custody for re-use at same site or other site location hills area up to 16 km from motor Vehicle road complete all as specified and as directed. |
| 61 | All as per item No.60 here-in-before but size 100 mm bore. |
| 62 | All as per item No.60 here-in-before but size 80 mm bore. |
| 63 | All as per item No.60 here-in-before but size 50 mm bore. |
| 64 | All as per item No.60 here-in-before but size 40 mm bore. |
| 65 | All as per item No.60 here-in-before but size 25 mm bore. |
| 66 | Supply, laying, connecting and testing, 150mm bore, Steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures ( Elbow, Nipple, Socket, Union, Tee, Reducer etc) complete laid in trenches etc location hills area up to 16 km from motor Vehicle road complete all as specified and as directed. |
| 67 | All as per item No.66 here-in-before but size 100mm dia |
| 68 | All as per item No.66 here-in-before but size 80 mm dia |
| 69 | All as per item No.66 here-in-before but size 50 mm dia |
| 70 | All as per item No.66 here-in-before but size 40 mm dia |
| 71 | S & F gun metal gate valve with inner wheel head, screwed both ends in iron pipe and fixed in 40mm dia complete all as specified and directed. |
| 72 | All as per item No.71 here-in-before but size 50mm dia |
| 73 | M & L for cast iron/GI fittings for spigot and socketed pipe, such as bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. \\"Y\\" junction, double branch, cross (all sockets or socket and pigot) collars, caps and plugs etc upto 150mm bore complete all as specified and as directed. |
| 74 | M & L for DI Mechanical Joint 150mm (raising stem type) with iron wheel head and stainless steel spindle including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket complete all as specified and as directed. |
| 75 | All as per item No.74 here-in-before but size 100 mm bore. |
| 76 | All as per item No.74 here-in-before but size 80 mm bore. |
| 77 | M & L for leakage rectification, cutting of existing pipe and making threaded for repair / replacement of unserviceable fittings etc pipe in short length ( up to 1.5 mtr ) for addition / alteration of 25 to 40 mm dia GI pipe and including replacement of fittings pipe in short lengths (up to 1.5 mtrs) of 25 to 40 mm dia GI pipe, welding including necessary excavation & earth work as required for making it serviceable complete all as specified and directed. |
| 78 | All as per item No.77 above but 50 to 80 mm bore of pipe. |
| 79 | All as per item No.77 above but 100 to150 mm bore of pipe. |
| 80 | M & L for run lead joints for spigot and socket CI / DI fittings/pipes incl spurn yarn complete for 150 mm bore pipes complete all as specified and as directed. |
| 81 | M & L f run lead joints for spigot and socket CI / DI fittings/pipes incl spurn yarn coromplete for 100 mm bore pipes all as specified and as directed. |
| 82 | S&F in replacement Air release valves, cast iron of size 4 to 6 inch with cover and all fixing accessories, riser pipe connection etc complete all as specified and directed. Please Enable Macros to View BoQ information |
